Effects of Nozzle Diameter and Holes Number on the Performance and Emissions of a Gasoline Direct Injection Engine

Year 2024, Volume: 27 Issue: 1, 1 - 12, 01.03.2024

Omar Yousef , Mahmoud Mashkour

https://doi.org/10.5541/ijot.1272871

Abstract

The goal of the current study is to estimate how a gasoline direct injection (GDI) engine's performance and emissions are affected by the fuel injector nozzle diameter and hole number of its injectors. A thermodynamic mathematical modelling has been created utilizing a software program written in the MATLAB language to simulate the two-zone combustion process of a four-stroke direct injection engine running on gasoline at (Rotation Engine Speed 3000 revolution per minute (rpm), 40 MPa injection pressure, compression ratio 9.5, and spark timing 145°). The first law of thermodynamics, equation of energy, mass conserving, equation of state, and mass fraction burned were all used in the creation of the software program. The study was carried out at five different nozzle diameters (0.250, 0.350, 0.450, 0.550, and 0.650 mm) and nozzle hole numbers (4,6,8,10,12). The results show that the GDI engine's performance and emissions are significantly influenced by variations in nozzle hole diameter and number. It was shown that engine power, heat transfer, cylinder pressure, and temperature increased with increasing nozzle hole diameter and number of nozzle holes and the maximum value was seen with nozzle hole diameter 0.650 mm and (12) holes. The lowest value for the nozzle hole diameter and number of holes was found to be 0.250 mm and 4 nozzle holes, which resulted in the lowest emissions of carbon monoxide CO and nitrogen monoxide NO. The study was also conducted for different operating conditions (Rotation Engine speed of 1000, 2000, 3000, 4000, 5000 rpm ,35 MPa injection pressure , compression ratio of 11.5 , and spark timing of 140° ) and the same nozzle diameters and nozzle holes number mentioned previously to estimate the maximum values for temperature, pressure, power , heat transfer and emissions . The results of the second part of the study showed that the highest of maximum values of temperature, pressure, and emissions were at of 1000 rpm, a nozzle diameter of 0.650 mm, and (12) holes. The highest values for maximum power at 4000 rpm, a nozzle diameter of 0.650 mm and (12) holes, while the highest maximum values for heat transfer are at 5000 rpm, a diameter of 0.65mm and (12) holes.

Keywords

Gasoline direct injection engine, mathematical model, performance

References

• F. Zhao, M. C. Lai, and D. L. Harrington, “Automotive spark-ignited direct-injection gasoline engines,” Prog. Energy Combust. Sci., vol. 25, no. 5, pp. 437–562, 1999, doi: 10.1016/S0360-1285(99)00004-0.
• J. Gao, D.-M Jiang, Z.-H Huang, X.-B Wang, “Numerical Study on Spray and Mixture Stratified Combustion in a Direct Injection Gasoline Engine,” Chinese Society for Internal Combustion Engines., vol 23 (4), pp. 297-306, 2005
• M. A. Mashkour, “Investigation of Spark Ignition Engine Mathematical Model Using MATLAB (GUI),” Advances in Natural and Applied Sciences. vol 11 (11) ,pp 36-50, 2017, [Online]. Available: http://www.aensiweb.com/ANAS.
• R. Sharma, “Experimental study of the Effect of Fuel Injector nozzle holes on Direct Injection Diesel Engine,” IOSR J. Mech. Civ. Eng., vol. 7, no. 4, pp. 67–74, 2013, doi: 10.9790/1684-0746774.
• Y. J. C. and C. H. J. B. H. LEE, J. H. SONG, “Effect of The Number of Fuel Injector Holes on Characteristics of Combustion and Emissions in A Dlesel Engine,” Int. J. Automot. Technol., vol. 11, no. 6, pp. 783–791, 2010, doi: 10.1007/s12239.
• M. Vijay Kumar, A. Veeresh babu, P. Ravi Kumar, and T. Manoj Kumar Dundi, “Influence of different nozzle hole orifice diameter on performance, combustion and emissions in a diesel engine,” Aust. J. Mech. Eng., vol. 18, no. 2, pp. 179–184, 2020, doi: 10.1080/14484846.2018.1453975.
• C. Jiang, M. C. Parker, J. Helie, A. Spencer, C. P. Garner, and G. Wigley, “Impact of gasoline direct injection fuel injector hole geometry on spray characteristics under flash boiling and ambient conditions,” Fuel, vol. 241, no., pp. 71–82, 2019, doi: 10.1016/j.fuel.2018.11.143.
• M. B. Ahmed and M. W. Mekonen, “Effects of Injector Nozzle Number of Holes and Fuel Injection Pressures on the Diesel Engine Characteristics Operated with Waste Cooking Oil Biodiesel Blends,” Fuels, vol. 3, no. 2, pp. 275–294, 2022, doi: 10.3390/fuels3020017.
• A. A. Reddy and J. M. Mallikarjuna, “Parametric Study on a Gasoline Direct Injection Engine - A CFD Analysis,” SAE Tech., Paper no 2017-26-0039, 2017, doi: 10.4271/2017-26-0039.
• P. D. Jadhav and J. M. Mallikarjuna, “Effect of fuel injector hole diameter and injection timing on the mixture formation in a GDI engine - A CFD study,” Int. J. Comput. Methods Exp. Meas., vol. 6, no. 4, pp. 737–748, 2018, doi: 10.2495/CMEM-V6-N4-737-748.
• J. B. Heywood, Internal Combustion Engine Fundamentals. N. York: McGraw-Hill , pp. 389–716, 1988
• Y. G. Guezennec and W. Hamama, “Two-zone heat release analysis of combustion data and calibration of heat transfer correlation in an I. C. engine,” SAE Tech. Paper., no. 724, 1999, doi: 10.4271/1999-01-0218.
• G. P. Blair, The Basic Design of Two-Stroke Engines,USA. Society of Automotive Engineers, Inc 400 commonwealth engine, pp.205-297, 1990 doi: 10.4271/r-104.
• W. J. D. Annand, “Heat Transfer in The Cylinders of Reciprocating Internal Combustion Engines,” Thermodynamics and Fluid Mechanics Group, vol. 177, no. 36, pp. 973–996, 1963, doi: 10.1243/PIME.
• D. L. Siebers, “Scaling liquid-phase fuel penetration in diesel sprays based on mixing-limited vaporization,” SAE Tech. Paper, no. 724, 1999, doi: 10.4271/1999-01-0528.
• C. R. F. A. T. Kirkpatrick, Internal Combustion Engines Applied Thermosciences, 3rd ed., John Wiley & Sons, Ltd, pp.84-120, 2016.
• C. Olikara and G. L. Borman, “A computer program for calculating properties of equilibrium combustion products with some applications to I.C. engines,” SAE Tech. Paper no 750468., 1975, doi: 10.4271/750468. [19] G. L. B. R. B. Krieger, The computation of apparent heat release for internal combustion engines. New York: ASME, pp66-WA/DGP-4 1966.