OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD

Volume: 6 Number: 1 February 1, 2011
  • Mustafa Günay
  • Alaattin Kaçal
  • Yakup Turgut
Engineering Sciences Cover
Engineering Sciences
PDF Download
EN TR

OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD

Abstract

This paper presents optimizing and effect of machining parameters on the cutting forces and surface roughness during face milling of Ti-6Al-4V alloy with carbide tools under dry conditions. Experimental setup was determined by using Taguchi design method. The optimum machining parameter combination was acquired by using signal-to-noise (S/N) ratio analysis. According to experimental results, resultant cutting forces and surface roughness increased with an increase in feed rate, whereas decreased with increase in cutting speed. Optimum machining conditions for the both resultant cutting forces (FR) and surface roughness (Ra) were obtained at cutting speed of 180 m/min and feed rate of 250 mm/min.

Keywords

Details

Primary Language

Turkish

Subjects

-

Journal Section

-

Authors

Mustafa Günay This is me

Alaattin Kaçal This is me

Yakup Turgut This is me

Publication Date

February 1, 2011

Submission Date

August 29, 2014

Acceptance Date

-

Published in Issue

Year 2011 Volume: 6 Number: 1

DOI

https://doi.org/10.12739/nwsaes.v6i1.5000067046

IZ

https://izlik.org/JA38MA99LZ

Cite

RIS / Bibtex
APA
Günay, M., Kaçal, A., & Turgut, Y. (2011). OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences, 6(1), 428-440. https://doi.org/10.12739/nwsaes.v6i1.5000067046
AMA
1.Günay M, Kaçal A, Turgut Y. OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences. 2011;6(1):428-440. doi:10.12739/nwsaes.v6i1.5000067046
Chicago
Günay, Mustafa, Alaattin Kaçal, and Yakup Turgut. 2011. “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”. Engineering Sciences 6 (1): 428-40. https://doi.org/10.12739/nwsaes.v6i1.5000067046.
EndNote
Günay M, Kaçal A, Turgut Y (February 1, 2011) OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences 6 1 428–440.
IEEE
[1]M. Günay, A. Kaçal, and Y. Turgut, “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”, Engineering Sciences, vol. 6, no. 1, pp. 428–440, Feb. 2011, doi: 10.12739/nwsaes.v6i1.5000067046.
ISNAD
Günay, Mustafa - Kaçal, Alaattin - Turgut, Yakup. “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”. Engineering Sciences 6/1 (February 1, 2011): 428-440. https://doi.org/10.12739/nwsaes.v6i1.5000067046.
JAMA
1.Günay M, Kaçal A, Turgut Y. OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences. 2011;6:428–440.
MLA
Günay, Mustafa, et al. “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”. Engineering Sciences, vol. 6, no. 1, Feb. 2011, pp. 428-40, doi:10.12739/nwsaes.v6i1.5000067046.
Vancouver
1.Mustafa Günay, Alaattin Kaçal, Yakup Turgut. OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences. 2011 Feb. 1;6(1):428-40. doi:10.12739/nwsaes.v6i1.5000067046