OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD

Cilt: 6 Sayı: 1 1 Şubat 2011
  • Mustafa Günay
  • Alaattin Kaçal
  • Yakup Turgut
Engineering Sciences Kapak
Engineering Sciences
PDF İndir
EN TR

OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD

Öz

This paper presents optimizing and effect of machining parameters on the cutting forces and surface roughness during face milling of Ti-6Al-4V alloy with carbide tools under dry conditions. Experimental setup was determined by using Taguchi design method. The optimum machining parameter combination was acquired by using signal-to-noise (S/N) ratio analysis. According to experimental results, resultant cutting forces and surface roughness increased with an increase in feed rate, whereas decreased with increase in cutting speed. Optimum machining conditions for the both resultant cutting forces (FR) and surface roughness (Ra) were obtained at cutting speed of 180 m/min and feed rate of 250 mm/min.

Anahtar Kelimeler

Ayrıntılar

Birincil Dil

Türkçe

Konular

-

Bölüm

-

Yazarlar

Mustafa Günay Bu kişi benim

Alaattin Kaçal Bu kişi benim

Yakup Turgut Bu kişi benim

Yayımlanma Tarihi

1 Şubat 2011

Gönderilme Tarihi

29 Ağustos 2014

Kabul Tarihi

-

Yayımlandığı Sayı

Yıl 2011 Cilt: 6 Sayı: 1

DOI

https://doi.org/10.12739/nwsaes.v6i1.5000067046

IZ

https://izlik.org/JA38MA99LZ

Kaynak Göster

RIS / Bibtex
APA
Günay, M., Kaçal, A., & Turgut, Y. (2011). OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences, 6(1), 428-440. https://doi.org/10.12739/nwsaes.v6i1.5000067046
AMA
1.Günay M, Kaçal A, Turgut Y. OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences. 2011;6(1):428-440. doi:10.12739/nwsaes.v6i1.5000067046
Chicago
Günay, Mustafa, Alaattin Kaçal, ve Yakup Turgut. 2011. “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”. Engineering Sciences 6 (1): 428-40. https://doi.org/10.12739/nwsaes.v6i1.5000067046.
EndNote
Günay M, Kaçal A, Turgut Y (01 Şubat 2011) OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences 6 1 428–440.
IEEE
[1]M. Günay, A. Kaçal, ve Y. Turgut, “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”, Engineering Sciences, c. 6, sy 1, ss. 428–440, Şub. 2011, doi: 10.12739/nwsaes.v6i1.5000067046.
ISNAD
Günay, Mustafa - Kaçal, Alaattin - Turgut, Yakup. “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”. Engineering Sciences 6/1 (01 Şubat 2011): 428-440. https://doi.org/10.12739/nwsaes.v6i1.5000067046.
JAMA
1.Günay M, Kaçal A, Turgut Y. OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences. 2011;6:428–440.
MLA
Günay, Mustafa, vd. “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”. Engineering Sciences, c. 6, sy 1, Şubat 2011, ss. 428-40, doi:10.12739/nwsaes.v6i1.5000067046.
Vancouver
1.Mustafa Günay, Alaattin Kaçal, Yakup Turgut. OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences. 01 Şubat 2011;6(1):428-40. doi:10.12739/nwsaes.v6i1.5000067046