Neutronic and Thermalhydraulic Evaluation of Annular Fuel in PWR with Three Different Nanofluids

Year 2022, , 643 - 654, 31.08.2022

Ali Tiftikçi

https://doi.org/10.16984/saufenbilder.1080287

Abstract

In pressurized nuclear reactors, one of the fuel design principles is the fuel centerline temperature limit. Since the thermal conductivity of UO2 is not high, the temperature increases rapidly from the fuel surface to the fuel center. To overcome this limitation, the use of annular type fuels instead of solid fuels is one of the improvement efforts. In this study, the effects of using annular fuel in a typical PWR are investigated. At the same time, the effects of adding nanoparticles (〖Al〗_2 O_3,Cu and TiO_2) to the coolant water in the case of solid and annular fuels are also investigated. For both cases, neutronic and thermalhydraulic calculations are made and compared. In neutronic point of view, it has been shown that the use of annular fuel does not cause a significant change in the k_eff value but the presence nanoparticles reduces the k_eff. This reduction is maximum for Cu+water and minimum for 〖Al〗_2 O_3+water nanofluids. In thermalhydraulic point of view, it has been shown that the annular fuel positively affects the fuel temperature limits and the addition of nanoparticles could provide an additional contribution to this, provided that it is in very small amounts (φ<0.01). Among the three nanoparticles examined, Cu+water is found to be the least suitable both in terms of neutronics and termalhydraulic considerations. TiO_2+water and 〖Al〗_2 O_3+water are comparable. It has also been shown that the optimum value for the annular fuel inner radius is approximately 0.4 cm.

Keywords

Annular fuel, nanofluid, Monte Carlo method, termalhydraulics

References

• [1] N. Tak, Y. Kim, J. Choi, W. J. Lee “Thermo-fluid investigation on a double-side-cooled annular fuel for the prismatic very high temperature gas-cooled reactor,” Nuclear Engineering and Design, vol. 238, pp. 2821–2827, 2008.
• [2] C. Y. Lee, C. H. Shin, W. K. In “Pressure drop in dual-cooled annular and cylindrical solid fuel assemblies for pressurized water reactor,” Nuclear Engineering and Design, vol. 250, pp. 287–293, 2012.
• [3] C. Zhao, L. Cao, H. Wu, Y. Zheng, “Pre-conceptual core design of SCWR with annular fuel rods,” Nuclear Engineering and Design, vol. 267, pp. 23–33, 2014.
• [4] V. Ghazanfari, M. Talebi, J. Khorsandi, R. Abdolahi, “Thermal-hydraulic modeling of water/Al2O3 nanofluid as the coolant in annular fuels for a typical VVER-1000 core,” Progress in Nuclear Energy, vol. 87, pp. 67–73, 2016.
• [5] E. Isik, V. Tugan, “Experimental and numerical analysis of the thermal performance of nanofluids used in automobile radiators,” Fresenius Environmental Bulletin, vol. 30, no. 9, pp. 10492-10504, 2021.
• [6] S. M. Peyghambarzadeh, S. H. Hashemabadi, M. S. Jamnani, S. M. Hoseini, “Improving the cooling performance of automobile radiator with Al2O3/water nanofluid,” Applied Thermal Engineering, vol. 31, pp. 1833-1838, 2011.
• [7] M. Ebrahimian, G. R. Ansarifar, “Investigation of the nano fluid effects on heat transfer characteristics in nuclear reactors with dual cooled annular fuel using CFD (Computational Fluid Dynamics) modeling,” Energy, vol. 98, pp. 1–14, 2016.
• [8] M. Z. Nejad, G.R. Ansarifar, “Design of a Small Modular Nuclear Reactor with dual cooled annular fuel and investigation of the fuel inner radius effect on the power peaking factor and natural circulation parameters,” Annals of Nuclear Energy, vol. 138, pp. 107185, 2020.
• [9] P. K. Romano, N. E. Horelik, B. R. Herman, A. G. Nelson, B. Forget, K. Smith, “OpenMC: A State-of-the-Art Monte Carlo Code for Research and Development,” Annals of Nuclear Energy, vol. 82, pp. 90–97, 2015.
• [10] Y. S. Yang, C. H. Shin, T. H. Chun, K. W. Song, “Evaluation of a Dual-Cooled Annular Fuel Heat Split and Temperature Distribution,” Journal of Nuclear Science and Technology, vol. 46, no. 8, pp. 836–845, 2009.
• [11] X. Wang, X. Xu, S. U. S. Choi, “Thermal Conductivity of Nanoparticles Fluid Mixture,” Journal of ThermoPhysic Heat Transfer, vol. 13, no. 4, pp. 474-80, 1999.
• [12] B. C. Pak, Y. I. Cho, “Hydrodynamic and Heat Transfer Study of Dispersed Fluids with Submicron Metallic Oxide Particle,” Experimental Heat Transfer, vol. 11, no. 2, pp. 151–170, 1998.
• [13] H. Chen, Y. Ding, Y. He, C. Tan “Rheological Behaviour of Ethylene Glycol Based Titania Nanofluids,” Chemical Physics Letters, vol. 444, no. 4, pp. 333–337, 2007.
• [14] P. D. Kukarni, K. D. Das, A. G. Chukwu, “Temperature Dependent Rheological Property of Copper Oxide Nanoparticle Suspension (Nanofluid),” Journal of Nanoscience and Nanotechnology, vol. 6, no. 4, pp. 1150–1154, 2006.
• [15] S. P. Jang, S. U. S. Choi, “Effects of various parameters on nanofluid thermal conductivity,” Journal of Heat Transfer, vol. 129, pp. 617-623, 2007.
• [16] G. Batchelor, “The effect of Brownian motion on the bulk stress in a suspension of spherical particles,” Journal of Fluid Mechanics, vol. 83, pp. 97–117, 1977.
• [17] K. Khanafer, K. Vafai, “A critical synthesis of thermophysical characteristics of nanofluids,” International Journal of Heat and Mass Transfer, vol. 54, pp. 4410–4428, 2011.