AN INVESTIGATION OF EFFECT OF CONTROL JETS LOCATION AND BLOWING PRESSURE RATIO TO CONTROL BASE PRESSURE IN SUDDENLY EXPANDED FLOWS

Year 2020, Volume: 6 Issue: 2 - Issue Name: Special Issue 11: 10th Eureca Conference Taylor's University Malaysia, Subangiaya, Malaysia, 15 - 23, 30.03.2020

Khizar Pathan Prakash Dabeer Sher Khan

https://doi.org/10.18186/thermal.726106

Cited By: 8

Abstract

The drag force is an essential factor in any projectile, from road vehicles to rocket or aircraft. The total drag includes skin friction drag, wave drag, and base drag. The base drag is the drag due to low pressure in the base region of the projectile. In the case of suddenly expanded flows, due to the sudden expansion of flow from the nozzle into the enlarged duct, the low pressure is created in the base region of the enlarged tube, which results in base drag and hence overall thrust reduced. In this paper, Computational Fluid Dynamic (CFD) analysis is used to analyze the effect of secondary air blowing jets called control jets to control base pressure in the base region of suddenly enlarged duct. These control jets are placed at different Pitch Circle Diameters (PCD) on the base face of the enlarged pipe. The objective of this work is to increase the base pressure up to atmospheric pressure and hence reduces the base drag. Mach number 3.0 is considered for analysis. The CFD analysis is done for different combinations of Area Ratios (AR) (2, 5 and 8), Nozzle Pressure Ratios (NPR) (2, 5 and 8), and PCD (d1, d2, and d3).
Further analysis is done for different air blowing pressure ratios (BPR) to optimize air blowing pressure. The analysis results are plotted for different area ratios, nozzle pressure ratios, and PCD of control jets. By observing results, it can be concluded that the base pressure is strongly influenced by AR, NPR, and PCD of control jets. The air blowing pressure should be optimum to save energy, and the optimum values can be selected from the results.

Keywords

Area ratio, base pressure, Mach number

References

• [1] Pathan KA, Dabeer PS, Khan SA. Influence of expansion level on base pressure and reattachment length. CFD Letters 2019;11:22–36. http://www.akademiabaru.com/doc/CFDLV11_N5_P22_36.pdf
• [2] Pathan KA, Dabeer PS, Khan SA. Investigation of base pressure variations in internal and external suddenly expanded flows using CFD analysis. CFD Letters 2019;11:32–40. http://www.akademiabaru.com/doc/CFDLV11_N4_P32_40.pdf
• [3] Pathan KA, Dabeer PS, Khan SA. Effect of nozzle pressure ratio and control jets location to control base pressure in suddenly expanded flows. Journal of Applied Fluid Mechanics 2019;12:1127–1135. DOI: 10.29252/jafm.12.04.29495.
• [4] Pathan KA, Dabeer PS, Khan SA. Analysis of parameters affecting thrust and base pressure in suddenly expanded flow from nozzle. Journal of Advanced Research in Fluid Mechanics and Thermal Sciences 2019;64:1–18. http://www.akademiabaru.com/doc/ARFMTSV64_N1_P1_18.pdf
• [5] Fharukh AGM, Ullah MA, Khan SA. Experimental study of suddenly expanded flow from correctly expanded nozzles. ARPN Journal of Engineering and Applied Sciences 2016;11:10041-10047.
• [6] Pathan KA, Dabeer PS, Khan SA. CFD analysis of the effect of Mach number area ratio and nozzle pressure ratio on velocity for suddenly expanded flows. 2017 2nd International Conference for Convergence in Technology I2CT 2017;1104–1110. DOI: 10.1109/I2CT.2017.8226299.
• [7] Pathan KA, Dabeer PS, Khan SA. CFD analysis of the effect of flow and geometry parameters on thrust force created by flow from nozzle. 2017 2nd International Conference for Convergence in Technology I2CT 2017;1121–1125. DOI: 10.1109/I2CT.2017.8226302.
• [8] Asadullah M, Khan SA, Asrar W, Sulaeman E. Low-cost base drag reduction technique. International Journal of Mechanical Engineering and Robotics Research 2018;7:428–432. DOI: 10.18178/ijmerr.7.4.428-432.
• [9] Gad-el-Hak. Flow control: passive, active, and reactive flow management. Cambridge University Press 2000.
• [10] Khan SA, Aabid A, Saleel CA. Influence of micro jets on the flow development in the enlarged duct at supersonic Mach number. International Journal of Mechanical and Mechatronics Engineering 2019;19:70–82.
• [12] Khan SA, Aabid A, Ghasi FAM, Al-Robaian AA, Alsagri AS. Analysis of area ratio in a CD nozzle with suddenly expanded duct using CFD method. CFD Letters 2019;11:61–71.
• [13] Khan SA, Aabid A, Mokashi I, Al-Robaian AA, Alsagri AS. Optimization of two-dimensional wedge flow field at supersonic Mach number. CFD Letters 2019;11:80–97.
• [14] Pathan KA, Dabeer PS, Khan SA. An investigation to control base pressure in suddenly expanded flows. International Review of Aerospace Engineering 2018;11:162–169. doi.org/10.15866/irease.v11i4.14675.
• [15] Pathan KA, Dabeer PS, Khan SA. Optimization of area ratio and thrust in suddenly expanded flow at supersonic Mach numbers. Case Studies in Thermal Engineering 2018;12:696–700 doi.org/10.1016/j.csite.2018.09.006
• [16] Pathan KA, Dabeer PS, Khan SA. CFD analysis of the effect of area ratio on suddenly expanded flows. 2017 2nd International Conference for Convergence in Technology I2CT 2017;1192–1198. DOI: 10.1109/I2CT.2017.8226315
• [17] Asadullah M, Khan SA, Asrar W, Sulaeman E. Passive control of base pressure with static cylinder at supersonic flow. IOP Conference Series: Materials Science and Engineering 2018;370:012050.
• [18] Khan SA, Fatepurwala MA, Pathan KN, Dabeer PS, Baig MAA. CFD analysis of human powered submarine to minimize drag. International Journal of Mechanical and Production Engineering Research and Development 2018;8:1057–1066. DOI: 10.24247/ijmperdjun2018111.
• [19] Seckin C. Investigation of the effect of the primary nozzle throat diameter on the evaporator performance of an ejector expansion refrigeration cycle. Journal of Thermal Engineering 2018;4:1939–1953. DOI: 10.18186/journal-of-thermal-engineering.408659.
• [20] Erdinç MT, Yılmaz T. Numerical investigation of flow and heat transfer in communicating converging and diverging channels. Journal of Thermal Engineering 2018;4:2318–2332. DOI: 10.18186/thermal.439057.
• [21] Sharma A, Gupta A, Singh H. Flow performance comparison alog the centerline in straight and S-shaped diffuser. Journal of Thermal Engineering 2020;6:58–71. DOI: 10.18186/thermal.671147.