Design and manufacture of the Torque test setup for small and shapeless materials

Year 2022, Volume: 6 Issue: 1, 81 - 86, 30.01.2022

Zeliha Coşkun , Talip Çelik , Yasin Kişioğlu

https://doi.org/10.31127/tuje.843320

Cited By: 1

Abstract

In this study, the design and manufacture of torque test set up has been carried out for small and shapeless speciment. The torque sensor, which has maximum 10 Nm, is used in the test system design. The certain specification of Nema 34 step motor which use to apply torsional force to the specimens is 12 Nm, 24V and 4.2 ampere. The step motor is controlled by the HY- DIV268N-5A Step Motor Driver and the supply voltage of driver is 24 Volts. The information about the degree of the specimen rotation was taken from potantiometer. The information obtained from the sensor and potentiometer was transferred to the LabVIEW software to be representation graphically using the USB 6003 DAQ card. The first metatarsal bone modelled from computerized tomography (CT) images was produced by Ultimaker2 3D printer using polylactic acid (PLA) material. The printed bone model was tested through torsion test set up. At the same time, the 3D bone was prepared for finite element analysis. Boundary conditions were applied in the finite element analysis (FEA) model in accordance with the test setup. The produced bones using 3D printer were subjected to torsion test with the test setup. Also the modelled bone was tested in accordance with the torsion test setup by using finite element analysis. After that, the FEA and experimental test results were compared with each other. As a conclusion, the optimization of the torsional test setup was performed based on the FEA.

Keywords

Torque Test Setup, FEA, First metatarsal, Bone PLA

Project Number

FHD-2020-2143

References

• Abutahoun I, Ha Jung-Hong, Kwak S & Kim Hyeon-Cheol (2018). Evaluation of dynamic and static torsional resistances of nickel-titanium rotary instruments. Journal of dental sciences.
• Ağın B, Çelik T & Kişioğlu Y (2019). Gezen Tavuklar İle Çiftlik Tavuklarinin Femur Kemiklerinin Mekanik Özelliklerinin Belirlenmesi Ve Karşilaştirilmasi.2. Uluslararasi Erciyes Bilimsel Araştirmalar Kongresi
• Çelik T, Mutlu İ, Özkan A & Kişioğlu Y (2017). The effect of cement on hip stem fixation: a biomechanical study. Australasian physical & engineering sciences in medicine, 40(2), 349- 357.
• Dahl K A, Moritz N & Vallittu P K (2018). Flexural and torsional properties of a glass fiber-reinforced composite diaphyseal bone model with multidirectional fiber orientation. Journal of the Mechanical Behavior of Biomedical Materials, 87, 143-147.
• Fatihhi S J, Rabiatul A A R, Harun M N, Kadir M R A, Kamarul T & Syahrom A (2016). Effect of torsional loading on compressive fatigue behaviour of trabecular bone. Journal of the mechanical behavior of biomedical materials, 54, 21-32.
• Kaur M & Singh K (2019). Review on titanium and titanium based alloys as biomaterials for orthopaedic applications. Materials Science and Engineering: C, 102, 844-862.
• Kasra M & Grynpas M D (2007). On shear properties of trabecular bone under torsional loading: effects of bone marrow and strain rate. Journal of Biomechanics, 40(13), 2898-2903.
• Kaygusuz B, Ozeri̇nç S (2019). 3 Boyutlu Yazıcı ile Üretilen PLA Bazlı Yapıların Mekanik Özelliklerinin İncelenmesi. Makina Tasarım ve İmalat Dergisi, 1-6.
• Kirthana S, Supraja M B, Vishwa A S N & Mahalakshmi N (2020). Static structural Analysis on Femur Bone Using Different Plate Material. Materials Today: Proceedings, 22, 2324-2333.
• Kumar K N, Griya N, Shaikh A, Chaudhry V & Chavadaki S (2020). Structural analysis of femur bone to predict the suitable alternative material. Materials Today: Proceedings, 26, 364-368.
• Kumar S, Nehra M, Kedia D, Dilbaghi N, Tankeshwar K & Kim K H (2020). Nanotechnology-based biomaterials for orthopaedic applications: Recent advances and future prospects. Materials Science and Engineering: C, 106, 110154.
• Kuwashima U, Takeuchi R, Ishikawa H, Shioda M, Nakashima Y & Schröter S (2019). Comparison of torsional changes in the tibia following a lateral closed or medial open wedge high tibial osteotomy. The Knee, 26(2), 374-381.
• Murakami Y. (2019), Torsional fatigue. Metal Fatigue (Second Edition), 317-340.
• Rohlmann A, Pohl, D & Bender A, Graichen F & Dymke J & Schmidt H & Bergmann G (2014). Activities of Everyday Life with High Spinal Loads. PloS one. 9. e98510. 10.1371/journal.pone.0098510.
• Sykaras N, Iacopino A M, Marker V A, Triplett R G & Woody R D (2000). Implant materials, designs, and surface topographies: their effect on osseointegration. A literature review. International Journal of Oral & Maxillofacial Implants, 15(5).
• Traphöner H, Clausmeyer T & Tekkaya A E (2018). Material characterization for plane and curved sheets using the in-plane torsion test–An overview. Journal of Materials Processing Technology, 257, 278-287.
• Varghese B, Short D, Penmetsa R, Goswami T & Hangartner T (2011). Computed-tomography- based finite-element models of long bones can accurately capture strain response to bending and torsion. Journal of biomechanics, 44(7), 1374- 1379.
• Wahab A H A, Wui N B, Kadir M R A & Ramlee M H (2020). Biomechanical Evaluation of Three Different Configurations of External Fixators for Treating Distal Third Tibia Fracture: Finite Element Analysis in Axial, Bending and Torsion Load. Computers in Biology and Medicine, 104062.
• Wu Z, Wu Y, Fahmy M (2020) Shear and torsional strengthening of structures. Structures Strengthened with Bonded Composites, 315- 386, 2020.