PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü ve Delaminasyon

Mehmet Boy

doi:10.53433/yyufbed.1104700

EN TR

Effects of Drilling Parameters on Drilling of PEEK-CF30 Thermoplastic Material: Thrust Force, Surface Roughness and Delamination

Abstract

In this study, the variations of thrust force, surface roughness and delamination factor according to cutting parameters were investigated in the drilling of Poly-ether-ether-ketone (PEEK)-CF30 composite material with uncoated HSS drill. Drilling experiments were carried out under dry machining conditions using three different cutting speeds (40, 80, 120 m/min) and feed rates (0.1, 0.15, 0.2 mm/rev). The thrust forces in drilling were measured with the Kistler dynamometer and equipment, and the results were analyzed by taking the arithmetic average of the data. The roughness on the hole surface and the delamination damages on the hole exit were measured. With the increase of the feed rate, there was an increase of 3%-25% in the thrust force, while the increase in the thrust forces was observed in the range of 9%-28% with the increase of the cutting speed. The surface quality improved with the decrease in cutting speed and increase in feed rate while the delamination factor increased. The lowest surface roughness was obtained as 1.18 µm at 40 m/min cutting speed and 0.2 mm/rev feed, and the highest surface roughness was 2.96 µm at 120 m/min cutting speed and 0.1 mm/rev feed.

Keywords

Delamimation, Drilling force, PEEK CF30, Surface roughness, Thermoplastic composite

PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü ve Delaminasyon

Abstract

Bu çalışmada, Poli-eter-eter-keton (PEEK)-CF30 kompozit malzemenin kaplamasız HSS matkapla delinmesinde oluşan itme kuvveti, yüzey pürüzlülüğü ve delaminasyon faktörünün kesme parametrelerine göre değişimleri araştırılmıştır. Delme deneyleri üç farklı kesme hızı (40, 80, 120 m/dk) ve ilerleme miktarı (0.1, 0.15, 0.2 mm/dev) kullanılarak kuru işleme şartlarında yapılmıştır. Delmede oluşan itme kuvvetleri Kistler dinamometre ve ekipmanlarıyla ölçülmüş ve elde edilen sonuçların aritmetik ortalaması alınarak analiz edilmiştir. Delik yüzeyinde oluşan pürüzlülük ile delik çıkışında oluşan delaminasyon hasarları ölçülmüştür. İlerleme miktarının artmasıyla itme kuvvetinde %3-%25’lik artış olurken, kesme hızının artmasıyla itme kuvvetlerinde %9-%28 aralığında artışlar görülmüştür. Kesme hızındaki azalma ve ilerleme miktarındaki artışla birlikte yüzey kalitesinde iyileşme olurken, delaminasyon faktöründe artış görülmüştür. En düşük yüzey pürüzlülüğü 40 m/dk kesme hızı ve 0.2 mm/dev ilerlemede 1.18 µm, en yüksek yüzey pürüzlülüğü 120 m/dk kesme hızı ve 0.1 mm/dev ilerlemede 2.96 µm olarak elde edilmiştir.

Keywords

Delaminasyon, Delme kuvveti, PEEK CF30, Termoplastik kompozit, Yüzey pürüzlülüğü

Supporting Institution

Karabük Üniversitesi

Project Number

KBÜ-BAP-16/2-YL-09

Thanks

Bilimsel Araştırma Projeleri Koordinatörlüğüne katkılarından dolayı teşekkür ederim.

References

Azmi, I., Lin R. J. T., & Bhattacharyya, D. (2013). Machinability study of glass fibre-reinforced polymer composites during end milling. The International Journal of Advanced Manufacturing Technology, 64, 247-261. doi: 10.1007/s00170-012-4006-6
Batista, M. F., Basso, I., Toti, F. A., Rodrigues, A. R., & Tarpani, J. R. (2020). Cryogenic drilling of carbon fibre reinforced thermoplastic and thermoset polymers. Composite Structures, 25, 112625. doi: 10.1016/j.compstruct.2020.112625
Bayraktar, Ş., Sıyambaş, Y., & Turgut, Y. (2017). Drilling process: A review. Sakarya University Journal of Science, 21(2), 120-130. doi: 10.16984/saufenbilder.296833
Cabrera, F. M., Khamlichi, A., Losilla, I., & Hanafi, I. (2012). Mathematical modelling for predicting surface roughness during machining of PEEK CF30 composite. International Review of Applied Sciences and Engineering, 3(2), 87-96. doi: 10.1556/IRASE.3.2012.2.1
Can, A. (2019). Study on the machinability of SMC composites during hole milling: influence of tool geometry and machining parameters. Arabian Journal for Science and Engineering, 44, 7599-7616. doi: 10.1007/s13369-019-03865-z
Davim, J. P., & Reis, P. (2004). Machinability study on composite (polyetheretherketone reinforced with 30% glass fibre–PEEK GF30) using polycrystalline diamond (PCD) and cemented carbide (K20) tools. The International Journal of Advanced Manufacturing Technology, 23, 412-418. doi: 10.1007/s00170-003-1779-7
Davim, J. P., & Mata, F. (2007). New machinability study of glass fiber reinforced plastics using polycrystalline diamond and cemented carbide (K15) tools. Materials & Design, 28, 1050–1054. doi: 10.1016/j.matdes.2005.09.019
Davim, J. P., & Mata, F. (2008). Chemical vapour deposition (CVD) diamond coated tools performance in machining of PEEK composites. Materials & Design, 29, 1568-1574. doi: 10.1016/j.matdes.2007.11.002
Domingo, R., García, M., & Gómez, M. R. (2013). Determination of energy during the dry drilling of PEEK GF30 considering the effect of torque. Procedia Engineering, 63, 687-693. doi: 10.1016/j.proeng.2013.08.195
Domingo, R., Marín, M., Agustina, B., & Calvo, R. (2015). Delamination analysis of polymeric materials during the drilling process. Procedia Engineering, 132, 448-455. doi: 10.1016/j.proeng.2015.12.518

Domingo, R., Agustina, B., & Marín M. M. (2020). Study of drilling process by cooling compressed air in reinforced polyether-ether-ketone. Materials, 13(8), 1965. doi: 10.3390/ma13081965
Du, Y., Yang, T., Liu, C., & Sun, Y. (2022). Damage performance in drilling of carbon fiber-reinforced polyetheretherketone composites using drills with different geometries. The International Journal of Advanced Manufacturing Technology, 121, 1743-1753. doi: 10.1007/s00170-022-09430-7
Ficici, F., Ayparcası, Z., & Ünal, H. (2017). Influence of cutting tool and conditions on machinability aspects of polyphthalamide (PPA) matrix composite materials with 30 % glass fiber reinforced. The International Journal of Advanced Manufacturing Technology, 90, 3067-3073. doi: 10.1007/s00170-016-9626-9
Ficici, F. (2021). Investigation of thrust force in drilling polyphthalamide (PPA) composites. Measurement, 182, 109505. doi: 10.1016/j.measurement.2021.109505
Izamshah, R., Azam, M. A., Hadzley M., Md Ali, M. A., Kasim, M. S., & Abdul Aziz M. S. (2013). Study of surface roughness on milling unfilled polyetheretherketones engineering plastics. Procedia Engineering, 68, 654-660. doi: 10.1016/j.proeng.2013.12.235
Klocke, F., Shirobokova, A., Kerchnawe S., Wahl, M., Mannensa, R., Feuerhacka, A., & Mattfelda, P. (2017). Experimental investigation of the hole accuracy, delamination, and cutting force in piercing of carbon fiber reinforced plastics. Procedia CIRP, 66, 215-220. doi: 10.1016/j.procir.2017.03.297
Lopez-Arraiza A., Amenabar I., Agirregomezkorta, A., Sarrionandia, M., & Aurrekoetxea, J. (2012). Experimental analysis of drilling damage in carbon-fiber reinforced thermoplastic laminates manufactured by resin transfer molding. Journal of Composite Materials, 46, 717-25. doi: 10.1177/0021998311414218
Mata, F., Gaitonde, V. N., Karnik, S. R., & Davim J. P. (2009). Influence of cutting conditions on machinability aspects of PEEK, PEEK CF 30 and PEEK GF 30 composites using PCD tools. Journal of Materials Processing Technology, 209, 1980-1987. doi: 10.1016/j.jmatprotec.2008.04.060
Mata, F., Beamud, E., Hanafi, I., Khamlichi, A., Jabbouri, A., & Bezzazi, M. (2010). Multiple regression prediction model for cutting forces in turning carbon-reinforced PEEK CF30. Advances in Materials Science and Engineering, 1-7. doi: 10.1155/2010/824098
McLauchlin, A. R., Ghita, O. R., & Savage, L. (2014). Studies on the reprocessability of poly (ether ether ketone) (PEEK). Journal of Materials Processing Technology, 214, 75-80. doi: 10.1016/j.jmatprotec.2013.07.010
Palanikumar, K., Latha, B., Senthilkumar, V., & Paulo, D. J. (2012). Analysis on drilling of glass fiber–reinforced polymer (GFRP) composites using Grey relational analysis. Materials and Manufacturing Processes, 27, 297-305. doi: 10.1080/10426914.2011.577865
Rahman, M., Ramakrishna, S., & Thoo, H. C. (1999). Machinability study of carbon/PEEK composites. Machining Science and Technology, 3(1), 49-59. doi: 10.1080/10940349908945682
Rajamurugan, T. V., Shanmugam, K., & Palanikumar, K. (2013). Analysis of delamination in drilling glass fiber reinforced polyester composites. Materials & Design, 45, 80–87. doi: 10.1016/j.matdes.2012.08.047
Seo, J., Banerjee, N., Kim, Y., Kim, D. C. & Park, H. W. (2020). Experimental and analytical investigation of the drilling forces of the carbon fiber reinforced plastics including thermal effects, Journal of Manufacturing Processes, 58, 1126-1137. doi: 10.1016/j.jmapro.2020.08.063
Sur, G., & Erkan, Ö. (2018). Cutting tool geometry in the drilling of CFRP composite plates and Taguchi optimisation of the cutting parameters affecting delamination. Sigma Journal of Engineering and Natural Sciences, 36(3), 619-628.
Susac, F., Tabacaru, V., Teodor, V. G., & Baroıu, N. (2019). Effect of cutting parameters on the hole quality in dry drilling of some thermoplastic polymers. Materiale Plastice, 56, 1. doi: 10.37358/MP.19.1.5160
Thiruchitrambalam, M., Bubesh Kumar, D., Shanmugam D., & Jawaid, M. (2020). A review on PEEK composites - Manufacturing methods, properties and applications. Materials Today: Proceedings, 33, 1085-1092. doi: 10.1016/j.matpr.2020.07.124
Uslu, G., Demirhan, M., Yaşar, N., & Korkmaz, M. E. (2022). Influence of glass fiber ratio on machining characteristics of PA66 polymer for aerospace applications. İmalat Teknolojileri ve Uygulamaları, 3(1), 59-66. doi: 10.52795/mateca.1080444
Vigneshwaran, S., Uthayakumar, M., & Arumugaprabu, V. (2018). Review on machinability of fiber reinforced polymers: A drilling approach. Silicon, 10, 2295–2305. doi: 10.1007/s12633-018-9764-9
Weinert, K., & Kempmann, C. (2004). Cutting temperatures and their effects on the machining behavior in drilling reinforced plastic composites. Advanced Engineering Materials, 6(8), 684-689. doi: 10.1002/adem.200400025
Weinert, K., Brinkel, F., Kempmann, C., & Pantke, K. (2007). The dependency of material properties and process conditions on the cutting temperatures when drilling polymers. Production Engineering - Research and Development, 1, 381-387. doi: 10.1007/s11740-007-0015-y
Xu, J., Huang X., Davim J. P., Ji, M., & Chen, M. (2020). On the machining behavior of carbon fiber reinforced polyimide and PEEK thermoplastic composites. Polymer Composites, 41, 3649-3663. doi:10.1002/pc.25663
Xu, J., Yin, Y., Davim, J. P., Li, L., Ji, M., Geier, N., & Chen, M., (2022). A critical review addressing drilling-induced damage of CFRP composites. Composite Structures, 294, 115594. doi: 10.1016/j.compstruct.2022.115594
Yaşar, N., Korkmaz, M. E., & Günay, M. (2017). Investigation on hole quality of cutting conditions in drilling of CFRP composite. MATEC Web of Conferences, 112, 01013. doi: 10.1051/matecconf/20171120101
Yaşar, N., & Günay, M. (2019). Experimental investigation on novel drilling strategy of CFRP laminates using variable feed rate. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 41, 150. doi: 10.1007/s40430-019-1658-2
Yazman, Ş. (2021). The effects of back-up on drilling machinability of filament wound GFRP composite pipes: Mechanical characterization and drilling tests. Journal of Manufacturing Processes, 68, 1535–1552. doi: 10.1016/j.jmapro.2021.06.054

Details

Primary Language

Turkish

Subjects

Engineering

Journal Section

Research Article

Authors

Mehmet Boy ^*
0000-0003-2471-8001
Türkiye

Publication Date

December 25, 2022

Submission Date

April 16, 2022

Acceptance Date

July 20, 2022

Published in Issue

Year 2022 Volume: 27 Number: 3

DOI

https://doi.org/10.53433/yyufbed.1104700

IZ

https://izlik.org/JA24FF93NR

APA

Boy, M. (2022). PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü ve Delaminasyon. Yüzüncü Yıl Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 27(3), 570-580. https://doi.org/10.53433/yyufbed.1104700

AMA

1.Boy M. PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü ve Delaminasyon. YYU JINAS. 2022;27(3):570-580. doi:10.53433/yyufbed.1104700

Chicago

Boy, Mehmet. 2022. “PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü Ve Delaminasyon”. Yüzüncü Yıl Üniversitesi Fen Bilimleri Enstitüsü Dergisi 27 (3): 570-80. https://doi.org/10.53433/yyufbed.1104700.

EndNote

Boy M (December 1, 2022) PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü ve Delaminasyon. Yüzüncü Yıl Üniversitesi Fen Bilimleri Enstitüsü Dergisi 27 3 570–580.

IEEE

[1]M. Boy, “PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü ve Delaminasyon”, YYU JINAS, vol. 27, no. 3, pp. 570–580, Dec. 2022, doi: 10.53433/yyufbed.1104700.

ISNAD

Boy, Mehmet. “PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü Ve Delaminasyon”. Yüzüncü Yıl Üniversitesi Fen Bilimleri Enstitüsü Dergisi 27/3 (December 1, 2022): 570-580. https://doi.org/10.53433/yyufbed.1104700.

JAMA

1.Boy M. PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü ve Delaminasyon. YYU JINAS. 2022;27:570–580.

MLA

Boy, Mehmet. “PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü Ve Delaminasyon”. Yüzüncü Yıl Üniversitesi Fen Bilimleri Enstitüsü Dergisi, vol. 27, no. 3, Dec. 2022, pp. 570-8, doi:10.53433/yyufbed.1104700.

Vancouver

1.Mehmet Boy. PEEK-CF30 Termoplastik Malzemenin Delinmesinde Delme Parametrelerinin Etkileri: İtme Kuvveti, Yüzey Pürüzlülüğü ve Delaminasyon. YYU JINAS. 2022 Dec. 1;27(3):570-8. doi:10.53433/yyufbed.1104700

Cited By

Investigation of Delamination in the Drilling of PLA Specimens with Different Lattice Structures

Yüzüncü Yıl Üniversitesi Fen Bilimleri Enstitüsü Dergisi

https://doi.org/10.53433/yyufbed.1401574