INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE

Mark Onipe

doi:10.57165/artgrid.1485767

TR EN

LATERİT KATKILI BETONUN BASINÇ DAYANIMI GELİŞİMİ VE SU EMME ORANI ÜZERİNDE KÜR ORTAMININ ETKİSİ

Öz

Bu çalışma, laterit kullanılarak kısmen veya tamamen geleneksel kumun yerine geçen sürdürülebilir bir malzeme olan laterit katkılı betonun basınç dayanımı ve su emme oranı üzerindeki farklı kür yöntemlerinin etkisini araştırmaktadır. 1 ila 28 gün arasındaki kür sürelerinde, laterit katkılı beton numuneleri suya daldırma, aralıklı sulama, ıslak bezle örtme, plastik örtüyle kaplama ve hava ile kürleme gibi farklı kür koşulları altında test edilmiştir. Sonuçlar, belirgin bir eğilim göstermektedir: Daha yüksek oranda laterit içeren betonların basınç dayanımı azalırken, su emme oranı (sorptivite) artmaktadır. Özellikle, 28 gün sonunda en yüksek basınç dayanımı (31.68 N/mm²) ve en düşük sorptivite değeri (0.0201 mm/√s) sürekli suya daldırma yöntemiyle elde edilmiştir. Bunu sırasıyla aralıklı sulama, ıslak bezle örtme, plastik örtüyle kaplama ve en düşük performansı sergileyen hava ile kürleme takip etmiştir. Çalışma, kür yöntemlerinin laterit katkılı betonun performansında belirleyici bir rol oynadığını vurgulamakta ve basınç dayanımı ile sorptivite arasında ters bir ilişki olduğunu ortaya koymaktadır. Ayrıca, kür süresi uzadıkça basınç dayanımının arttığı ve sorptivitenin azaldığı görülmektedir; bu durum, etkin kür uygulamalarının uzun vadeli önemini gözler önüne sermektedir. Elde edilen bulgular, doğru kür stratejilerinin seçilmesinin laterit katkılı beton yapıların dayanıklılığını ve performansını artırmak açısından büyük önem taşıdığını ortaya koymakta; böylece sürdürülebilir inşaat uygulamalarına katkı sunmaktadır.

Anahtar Kelimeler

Laterit katkılı beton, kür yöntemi, basınç dayanımı, sorptivite, sürdürülebilirlik

INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE

Öz

The study investigates the impact of different curing techniques on the compressive strength and absorption rate of laterised concrete, a sustainable material integrating laterite as a partial or full substitute for conventional sand. Over curing durations spanning 1 to 28 days, compressive strength and sorptivity of laterised concrete specimens were evaluated under varied curing conditions: water immersion, intermittent sprinkling, wet rug covering, plastic sheet covering, and air-drying. Results indicate a consistent trend: higher laterite content correlates with decreased compressive strength yet increased sorptivity. Notably, water immersion consistently yielded the highest compressive strength (31.68 N/mm²) and lowest sorptivity (0.0201 mm/√s) after 28 days, followed by intermittent sprinkling, wet rug, plastic sheet coverings, and air-drying, with the latter exhibiting the poorest performance. The study underscores the pivotal role of curing methods, revealing an inverse relationship between compressive strength and sorptivity. Moreover, as the curing duration extends, compressive strength improves while sorptivity diminishes, emphasising the enduring efficacy of curing. These insights accentuate the significance of selecting suitable curing strategies to enhance laterised concrete structures' performance and durability, thereby advancing sustainable construction practices.

Anahtar Kelimeler

Laterised concrete, Compressive strength, Sorptivity, Curing method, Sustainability

Proje Numarası

No external funding was received for this research.

Etik Beyan

Ethical Approval This article does not contain any studies with human participants or animals performed by any of the authors. Conflict of Interest The authors declare that they have no conflict of interest. Funding This research did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors. The authors personally funded this research.

Kaynakça

Abdel-Hay, A. S. (2017). Properties of recycled concrete aggregate under different curing conditions. HBRC Journal, 13(3), 271–276. https://doi.org/10.1016/j.hbrcj.2015.07.001
Abdurahman, A., Parviz, S., & Faiz. (1996). Effects of curing conditions and age on chloride permeability of fly ash mortar. ACI Materials Journal, 93(1). https://doi.org/10.14359/9800
Akinkurolere, O. O. (2021). Water absorption, sorptivity and permeability properties of concrete containing chemical and mineral admixtures. LAUTECH Journal of Civil and Environmental Studies, 6(2). https://doi.org/10.36108/laujoces/1202.60.0201
Alexander, M. G., Ballim, Y., & Stanish, K. (2008). A framework for use of durability indexes in performance-based design and specifications for reinforced concrete structures. Materials and Structures, 41, 921–936.
Aluko, O., Awolusi, T., & Adesina, A. (2020). Influence of curing media and mixing solution on the compressive strength of laterized concrete. Silicon, 12(10), 2425–2432. https://doi.org/10.1007/s12633-019-00343-x
Ambrose, E. E., Ekpo, D. U., Umoren, I. M., & Ekwere, U. S. (2018). Compressive strength and workability of laterized quarry sand concrete. Nigerian Journal of Technology, 37(3), 605. https://doi.org/10.4314/njt.v37i3.7
ASTM. (2013). Standard test method for measurement of rate of absorption of water by hydraulic-cement concretes, (ASTM C1585). ASTM International.
Atiş, C. D., Özcan, F., Kılıç, A., Karahan, O., Bilim, C., & Severcan, M. H. (2005). Influence of dry and wet curing conditions on compressive strength of silica fume concrete. Building and Environment, 40(12), 1678–1683. https://doi.org/10.1016/j.buildenv.2004.12.005
Awolusi, T. F., Sojobi, A. O., & Afolayan, J. O. (2017). SDA and laterite applications in concrete: Prospects and effects of elevated temperature. Cogent Engineering, 4(1), 1387954. https://doi.org/10.1080/23311916.2017.1387954
Awolusi, T. F., Oguntayo, D. O., Babalola, O. E., Oke, O. L., & Akinkurolere, O. O. (2021). Investigation of micronized laterite sandcrete block compressive strength. Case Studies in Construction Materials, 14, e00530. https://doi.org/10.1016/j.cscm.2021.e00530

Awoyera, P. O., Akinmusuru, J. O., Dawson, A. R., Ndambuki, J. M., & Thom, N. H. (2018). Microstructural characteristics, porosity and strength development in ceramic-laterized concrete. Cement and Concrete Composites, 86, 224–237. https://doi.org/10.1016/j.cemconcomp.2017.11.017
Balakrishna, M. N., Mohamad, M., Evans, R., & Rahman, M. M. (2020). Water absorption capacity of concrete cubes with sorptivity coefficient. Journal of Civil Engineering, 48(1), 17–27.
British Standard Institution. (2011). Cement composition, specification and conformity criteria for common cements, (BS EN 197-1:2007). British Standards Institution.
British Standards Institution. (2002). Mixing water for concrete. Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete (BS EN 1008:2002). British Standards Institution.
BS. (2009). Testing hardened concrete: Making and curing specimens for strength test, (BS EN 12390-2). British Standard Institution.
Chand, M. S. R., Giri, P. S. N. R., Kumar, G. R., & Kumar, P. R. (2015). Paraffin wax as an internal curing agent in ordinary concrete. Magazine of Concrete Research, 67(2), 82–88. https://doi.org/10.1680/macr.14.00192
Du, H., Gao, H. J., & Pang, S. D. (2016). Improvement in concrete resistance against water and chloride ingress by adding graphene nanoplatelet. Cement and Concrete Research, 83, 114–123. https://doi.org/10.1016/j.cemconres.2016.02.005
Esam, E., Amr, A. A. E. H., & Rania, A. F. I. (2014). Comparative study on strength, permeability and sorptivity of concrete and their relation with concrete durability. International Journal of Engineering and Innovative Technology, 4(4), 132–139.
Federowicz, K., Kaszyńska, M., Zieliński, A., & Hoffmann, M. (2020). Effect of curing methods on shrinkage development in 3d-printed concrete. Materials, 13(11), 2590. https://doi.org/10.3390/ma13112590
Folagbade, S. O. (2020). Effect of carbonation on the permeation properties of laterized concrete. American Journal of Engineering Research, 9(7), 93–102.
Gabriel-Wettey, F. K. N., Appiadu-Boakye, K., & Anewuoh, F. (2021). Impact of curing methods on the porosity and compressive strength of concrete. Journal of Engineering Research and Reports, 18–30. https://doi.org/10.9734/jerr/2021/v20i917371
Garba, I., Sulaiman, T. A., Kaura, J. M., & Abdullahi, M. (2024). Optimization and predictive models on strengths and durability of reinforced laterized concrete. Covenant journal of engineering technology. https://journals.covenantuniversity.edu.ng/index.php/cjet/article/view/4002
Gogineni, A., Panday, I. K., Kumar, P., & Paswan, R. Kr. (2024). Predicting compressive strength of concrete with fly ash and admixture using XGBoost: A comparative study of machine learning algorithms. Asian Journal of Civil Engineering, 25(1), 685–698. https://doi.org/10.1007/s42107-023-00804-0
Hall, C. (1989). Water sorptivity of mortars and concretes: A review. Magazine of Concrete Research, 41(147). https://doi.org/10.1680/macr.1989.41.147.51
Kamaruzaman, N. W., & Muthusamy, K. (2013). Effect of curing regime on compressive strength of concrete containing malaysian laterite aggregate. Advanced Materials Research, 626, 839–843. https://doi.org/10.4028/www.scientific.net/AMR.626.839
Kim, T.-K., Choi, S.-J., Choi, J.-H., & Kim, J.-H. J. (2019). Prediction of chloride penetration depth rate and diffusion coefficient rate of concrete from curing condition variations due to climate change effect. International Journal of Concrete Structures and Materials, 13(1), 15. https://doi.org/10.1186/s40069-019-0333-4
Kubissa, W., Wilińska, I., & Jaskulski, R. (2022). Study on the effect of VMA admixture for concrete cured under different conditions on air permeability and sorptivity. Construction and Building Materials, 346, 128350. https://doi.org/10.1016/j.conbuildmat.2022.128350
Kumar, P., & Pratap, B. (2024). Feature engineering for predicting compressive strength of high-strength concrete with machine learning models. Asian Journal of Civil Engineering, 25(1), 723–736. https://doi.org/10.1007/s42107-023-00807-x
Li, J., Chen, Z., & Chen, W. (2020). Axial load-bearing capacities of pre-cast self-insulation walls made by foam concrete. Structures, 27, 1951–1961. https://doi.org/10.1016/j.istruc.2020.08.001
Maroliya, M. K. (2012). Estimation of water sorptivity as durability index for ultra high strength reactive powder concrete. International Journal of Engineering Research and Development, 4(3), 53–56.
Mehta, P. K., & Monteiro, P. J. M. (2014). Concrete: Microstructure, Properties and Materials. McGraw-Hill, NewYork, NY, USA.
Moore, A. J., Bakera, A. T., & Alexander, M. G. (2021). A critical review of the water sorptivity index (WSI) parameter for potential durability assessment: Can WSI be considered in isolation of porosity? Journal of the South African Institution of Civil Engineering, 63(2), 27–34.
Odeyemi, S., Abdulwahab, R., Anifowose, M. A., & Atoyebi, O. D. (2021). Effect of curing methods on the compressive strengths of palm kernel shell concrete. Civil Engineering and Architecture. https://doi.org/10.13189/cea.2021.090716
Oni, O., & Arum, C. (2023). Workability and compressive strength of concrete containing binary cement, mixed fines, and superplasticizer. Facta Universitatis - Series: Architecture and Civil Engineering, 21(2), 299–314. https://doi.org/10.2298/FUACE220818017O
Onipe, M. O., & Fologbade, S. O. (2017). Void content and sorptivity of laterized concrete. Advances in Built Environment Research, 147–156.
Osei, D. Y., Mustapha, Z., & Zebilila, M. (2020). Compressive strength of concrete using different curing methods. Journal of Social and Development Sciences. https://doi.org/10.22610/jsds.v10i3(s).2983
Pan, J.-L., Shen, J.-X., Zhong, Z.-L., Xia, Y., Li, X.-D., & Zhang, Y.-Q. (2024). Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading. Engineering Failure Analysis, 161, 108240. https://doi.org/10.1016/j.engfailanal.2024.108240
Potdar, N. M., Abraham, S. M., & Kakade, V. (2023). Assessment of efficacy of curing practices in concrete. Materials Today: Proceedings. https://doi.org/10.1016/j.matpr.2023.04.025
Rachel, P. P. (2019). Experimental investigation on strength and durability of concrete using high volume flyash, GGBS and M-Sand. International Journal for Research in Applied Science and Engineering Technology, 7(3), 396–403. https://doi.org/10.22214/ijraset.2019.3069
Rehman, S. K. U., Imtiaz, L., Aslam, F., Khan, M. K., Haseeb, M., Javed, M. F., Alyousef, R., & Alabduljabbar, H. (2020). Experimental investigation of NaOH and KOH mixture in SCBA-based geopolymer cement composite. Materials, 13(15), 3437. https://doi.org/10.3390/ma13153437
Rucker-Gramm, P., & Beddoe, R. E. (2010). Effect of moisture content of concrete on water uptake. Cement and Concrete Research, 40(1), 102–108. https://doi.org/10.1016/j.cemconres.2009.09.001
Spijkerman, Z., Boshoff, W. P., & Smit, M. S. (2022). Effectiveness of concrete curing compounds in extreme windy and dry conditions. MATEC Web of Conferences, 364, 05006. https://doi.org/10.1051/matecconf/202236405006
Tanyildizi, M. (2022). The effect of cement replacement with eggshell powder on the sorptivity index of concrete. Bitlis Eren University Journal of Science and Technology, 12(1), 36–42. https://doi.org/10.17678/beuscitech.1077465
Udeme, H. I., Ufan, C. O., & Abraham, U. E. (2022). Comparative study of cube and cylinder crushing strengths of laterized concrete. International Journal of Multidisciplinary Research and Analysis, 7(2), 543–552. https://doi.org/10.47191/ijmra/v7-i02-16
Ukpata, J. O., Ewa, D. E., Success, N. G., Alaneme, G. U., Otu, O. N., & Olaiya, B. C. (2024). Effects of aggregate sizes on the performance of laterized concrete. Scientific Reports, 14(1), 448. https://doi.org/10.1038/s41598-023-50998-1
Wang, H., Guo, B., Guo, Y., Jiang, R., Zhao, F., & Wang, B. (2023). Effects of curing methods on the permeability and mechanism of cover concrete. Journal of Building Material Science, 5(1), Article 1. https://doi.org/10.30564/jbms.v5i1.5484
Wang, L., & Li, S. (2014). Capillary absorption of concrete after mechanical loading. Magazine of Concrete Research, 66(8), 420–431. https://doi.org/10.1680/macr.13.00331
Wedatalla, A. M. O., Yang, J., & Ahmed, A. A. M. (2019). Curing effects on high-strength concrete properties. Advances in Civil Engineering. https://doi.org/10.1155/2019/1683292
Yang, L., Liu, G., Gao, D., & Zhang, C. (2021). Experimental study on water absorption of unsaturated concrete: W/c ratio, coarse aggregate and saturation degree. Construction and Building Materials, 272, 121945. https://doi.org/10.1016/j.conbuildmat.2020.121945
Zhang, S. P., & Zong, L. (2014). Evaluation of relationship between water absorption and durability of concrete materials. Advances in Materials Science and Engineering, 2014, 650373. https://doi.org/10.1155/2014/650373
Zhou, J. (2023). Visualization of green building landscape space environment design based on image processing and artificial intelligence algorithm. Scite.Ai. https://doi.org/10.21203/rs.3.rs-2550309/v1
Zhuang, S., Wang, Q., & Zhang, M. (2022). Water absorption behaviour of concrete: Novel experimental findings and model characterization. Journal of Building Engineering, 53, 104602. https://doi.org/10.1016/j.jobe.2022.104602

Ayrıntılar

Birincil Dil

İngilizce

Konular

Mimarlıkta Malzeme ve Teknoloji

Bölüm

Araştırma Makalesi

Yazarlar

Mark Onipe ^*
0009-0001-3267-2026
Nigeria

Yayımlanma Tarihi

30 Haziran 2025

Gönderilme Tarihi

17 Mayıs 2024

Kabul Tarihi

24 Nisan 2025

Yayımlandığı Sayı

Yıl 2025 Cilt: 7 Sayı: 1

DOI

https://doi.org/10.57165/artgrid.1485767

IZ

https://izlik.org/JA38RD67JN

APA

Onipe, M. (2025). INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE. ArtGRID - Journal of Architecture Engineering and Fine Arts, 7(1), 114-131. https://doi.org/10.57165/artgrid.1485767

AMA

1.Onipe M. INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE. ArtGRID. 2025;7(1):114-131. doi:10.57165/artgrid.1485767

Chicago

Onipe, Mark. 2025. “INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE”. ArtGRID - Journal of Architecture Engineering and Fine Arts 7 (1): 114-31. https://doi.org/10.57165/artgrid.1485767.

EndNote

Onipe M (01 Haziran 2025) INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE. ArtGRID - Journal of Architecture Engineering and Fine Arts 7 1 114–131.

IEEE

[1]M. Onipe, “INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE”, ArtGRID, c. 7, sy 1, ss. 114–131, Haz. 2025, doi: 10.57165/artgrid.1485767.

ISNAD

Onipe, Mark. “INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE”. ArtGRID - Journal of Architecture Engineering and Fine Arts 7/1 (01 Haziran 2025): 114-131. https://doi.org/10.57165/artgrid.1485767.

JAMA

1.Onipe M. INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE. ArtGRID. 2025;7:114–131.

MLA

Onipe, Mark. “INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE”. ArtGRID - Journal of Architecture Engineering and Fine Arts, c. 7, sy 1, Haziran 2025, ss. 114-31, doi:10.57165/artgrid.1485767.

Vancouver

1.Mark Onipe. INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE. ArtGRID. 01 Haziran 2025;7(1):114-31. doi:10.57165/artgrid.1485767

Cited By

Designing 3D-printed concrete with ternary blended mortars incorporating fly ash and silica fume: effects of low water-binder ratios on workability and strength

Innovative Infrastructure Solutions

https://doi.org/10.1007/s41062-025-02474-0

LATERİT KATKILI BETONUN BASINÇ DAYANIMI GELİŞİMİ VE SU EMME ORANI ÜZERİNDE KÜR ORTAMININ ETKİSİ

Öz

Anahtar Kelimeler

INFLUENCE OF CURING MEDIA ON THE COMPRESSIVE STRENGTH DEVELOPMENT AND ABSORPTION RATE OF LATERIZED CONCRETE

Öz

Anahtar Kelimeler

Proje Numarası

Etik Beyan

Kaynakça

Ayrıntılar

Birincil Dil

Konular

Bölüm

Yazarlar

Yayımlanma Tarihi

Gönderilme Tarihi

Kabul Tarihi

Yayımlandığı Sayı

DOI

IZ

Kaynak Göster

Cited By

Designing 3D-printed concrete with ternary blended mortars incorporating fly ash and silica fume: effects of low water-binder ratios on workability and strength