Ahşap yapı, tekne
ve yapı malzemesinde, kusurlarından arındırılmış ve su itici özelliği
barındıran, mukavemeti yüksek ağaç malzemelere ihtiyaç duyulmaktadır. Bu
çalışma kapsamında poliüretan tutkalı ile lamine edilmiş karaçam ve doğu kayını
örneklerinin Wolmanit-CB ile emprenye edilerek, 12 ay süre ile deniz içi ve
sahil şartlarına maruz bırakılarak eğilme direnci üzerine etkisi
incelenmiştir. Deneylerde lamine ağaç
malzemeler TS EN 386’ya göre hava kurusu haldeki 5 mm kalınlığındaki papel
kaplamalarından, poliüretan tutkalı ile 4 katmanlı olarak toplam 120 adet deney
örneği hazırlanmıştır. Lamine üretimindeki pres basıncı, karaçam için 0,8 N/mm2,
doğu kayını için 1,2 N/mm2 uygulanmıştır. Farklı (ağaç, işlem ve
ortam) parametrelerin eğilme direnci ve elastikiyet modülü üzerindeki etkileri
TS 2474’e göre belirlenmiştir. Farklı şartların malzeme üzerindeki etkisini
belirlemek için yapılan testlerde, açık hava şartlarına maruz bırakılan
emprenyeli doğu kayınında en yüksek eğilme direnci tespit edilmiştir. Wolmanit-CB emprenye
uygulamasının sahilde bekletilen karaçamda %40,81, doğu kayınında %26,72, deniz
içinde bekletilen karaçamda %39,23, doğu kayınında %47,42 oranında emprenyesiz
örneklere göre eğilme dirençlerinde artış tespit edilmiştir. Deniz
içerisine bırakılan numuneler deniz delicileri tarafından tahrip edilmiş ayrıca
emprenyesiz numunelerde delik sayısı ve çapının daha fazla olduğu ve lamine
tutkal hattında açılmalar olduğu görülmüştür.
There is a need
for high strength wood materials that contain water repellent properties and
are free from defects in wooden structures, boats and construction materials.
In this study, the effect of the black pine and oriental beech samples
laminated with polyurethane glue on impregnation with Wolmanit-CB was
investigated with exposure to sea water and open-air conditions for 12 months.
In the experiments, laminated wood materials and polyurethane glue from 5 mm
thick papel coatings according to TS EN 386 were prepared in 4 layers with a
total of 120 test samples. The press pressure in laminate production was 0.8
N/mm2 for black pine wood and 1.2 N/mm2 for beech wood.
The effects of different parameters (wood, process and medium conditions) on
bending strength and modulus of elasticity were determined according to TS
2474. In the tests conducted to determine the effect of different conditions on
the material, the highest bending strength was determined in the impregnated
oriental beech exposed to the open-air conditions. Of all the Wolmanit-CB
impregnation 40.81% of the pine impregnation, 26.72% of the oriental beech,
39.23% of the natural beech in the sea, 47.42% of the oriental beech were found
to increase the bending strength of the samples. The samples released into the
sea were destroyed by the harmful sea organism and it was observed that the
number and diameter of the holes in the impregnated samples were higher and the
glue line was opened.
Birincil Dil | Türkçe |
---|---|
Konular | Kereste, Hamur ve Kağıt |
Bölüm | Biomaterial Engineering, Bio-based Materials, Wood Science |
Yazarlar | |
Yayımlanma Tarihi | 15 Aralık 2019 |
Yayımlandığı Sayı | Yıl 2019 Cilt: 21 Sayı: 3 |
Bartin Orman Fakultesi Dergisi Editorship,
Bartin University, Faculty of Forestry, Dean Floor No:106, Agdaci District, 74100 Bartin-Turkey.
Tel: +90 (378) 223 5094, Fax: +90 (378) 223 5062,
E-mail: bofdergi@gmail.com