Hibrit mikrodalga ısıtma yöntemiyle üretilen Al5Cu-B4C-Gr hibrit kompozitlerin kuru kayma aşınma davranışı

Öz

Bu çalışmada, farklı oranlarda bor karbür (B4C) ve grafit (Gr) ile takviye edilmiş Al5Cu matrisli hibrit kompozitler toz metalurjisi yöntemiyle üretilmiş ve ardından hibrit mikrodalga sinterleme uygulanmıştır. B4C ve Gr içeriklerinin kompozitlerin fiziksel, mikroyapısal, mekanik ve kuru kayma aşınma davranışları üzerindeki etkileri sistematik olarak incelenmiştir. Toz karakterizasyonu, düzensiz şekilli Al, küresele yakın Cu, köşeli B4C ve lamelli Gr partiküllerinin yoğunlaşma davranışı ve takviye dağılımı üzerinde etkili olan heterojen bir başlangıç toz mimarisi oluşturduğunu göstermiştir. Sinterleme sonrasında tüm numunelerde bağıl yoğunluk artmış ve porozite azalmıştır. En yüksek sinterlenmiş yoğunluk ve sinterlenebilirlik değeri (%37,26), en düşük toplam takviye oranına sahip AC1 numunesinde elde edilmiştir. XRD analizi Al matrisi, B4C, Gr, Al2Cu, Al2O3 ve Al7Cu2Fe fazlarının varlığını doğrulamıştır. SEM-EDX sonuçları, B4C ve Gr fazlarının matris içinde korunduğunu ve Al7Cu2Fe-tipi faz oluşumuyla ilişkili yerel Al–Fe–Cu zenginleşmesini desteklemiştir. En yüksek Brinell sertliği (65,23 HB) ve mikrosertlik (88,30 HV0,05) değerleri, yüksek B4C içeriği ve yeterli yoğunlaşma nedeniyle AC2 numunesinde gözlenmiştir. Buna karşılık, en düşük ortalama sürtünme katsayısı AC3 numunesinde (0,5040), en düşük özgül aşınma oranı ise AC4 numunesinde (1,9079 × 10-3 mm3/Nm) elde edilmiştir. Sonuçlar, aşınma direncinin yalnızca sertlik tarafından değil; B4C’nin yük taşıyıcı etkisi, Gr’nin yağlayıcı davranışı ve hibrit mikrodalga sinterleme sırasında gelişen mikroyapısal durumun birlikte etkisiyle belirlendiğini göstermektedir.

Anahtar Kelimeler

• Alüminyum matris kompozitleri
• Grafit (Gr)
• Hibrit mikrodalga sinterleme
• Kuru kayma aşınması
• Bor karbür

Dry sliding wear behavior of Al5Cu-B4C-Gr hybrid composites fabricated by hybrid microwave heating

Öz

In this study, Al5Cu matrix hybrid composites reinforced with varying ratios of boron carbide (B4C) and graphite (Gr) were produced via powder metallurgy, followed by hybrid microwave sintering. The effects of B4C and Gr contents on the physical, microstructural, mechanical, and dry sliding wear behavior of the composites were systematically evaluated. Powder characterization revealed that irregular Al, spheroidal Cu, angular B4C, and lamellar Gr particles formed a heterogeneous initial powder architecture that influenced densification and the distribution of reinforcement. After sintering, all samples exhibited increased relative density and reduced porosity. The highest sintered density and sinterability value (37.26%) were obtained for AC1, which had the lowest total reinforcement content. XRD analysis confirmed the presence of the Al matrix, B4C, Gr, Al2Cu, Al2O3, and Al7Cu2Fe phases. SEM-EDX results supported the retention of B4C and Gr within the matrix and confirmed the local Al-Fe-Cu enrichment associated with Al7Cu2Fe-type phase formation. The highest Brinell hardness (65.23 HB) and microhardness (88.30 HV0.05) were observed for AC2, owing to its higher B4C content and sufficient densification. In contrast, the lowest average coefficient of friction was measured for AC3 (0.5040), while the lowest specific wear rate was obtained for AC4 (1.9079×10-3 mm3/Nm). These results show that wear resistance was governed not by hardness alone, but by the combined load-bearing effect of B4C, the lubricating action of Gr, and the microstructural state developed during hybrid microwave sintering.

Anahtar Kelimeler

• Aluminum matrix composites
• Graphite (Gr)
• Hybrid microwave sintering
• Dry sliding wear
• Boron carbide

Kaynakça

1. Deaquino-Lara, R., Gutiérrez-Castañeda, E., Estrada- Guel, I., Hinojosa-Ruiz, G., García-Sánchez, E., Herrera-Ramírez, J. M., … & Martínez-Sánchez, R. (2014). Structural characterization of aluminium alloy 7075-graphite composites fabricated by mechanical alloying and hot extrusion. Materials & Design, 53, 1104- 1111. https://doi.org/10.1016/j.matdes.2013.08.005
2. Ayvaz, M. (2022). Characterization and tribological properties of novel AlCu4.5SiMg Alloy-(B4C/TiO2/nGr) quaternary hybrid composites sintered via microwave. Metals and Materials International, 28, 710-721. https:// doi.org/10.1007/s12540-020-00894-4
3. Akkaş, M., & Al, S. (2021). Effect of hot pressing and reinforcement of TiC and WC on the mechanical properties and microstructure of AlCuFeCrNi HEAs alloy. Science of Sintering, 53(1), 19-35. https://doi. org/10.2298/SOS2101019A
4. Singh, J., & Chauhan, A. (2016). Overview of wear performance of aluminium matrix composites reinforced with ceramic materials under the influence of controllable variables. Ceramics International, 42(1), 56-81. https:// doi.org/10.1016/j.ceramint.2015.08.150
5. Valizade, N., & Farhat, Z. (2024). A review on abrasive wear of aluminum composites: Mechanisms and influencing factors. Journal of Composites Science, 8(4), 149. https://doi.org/10.3390/jcs8040149
6. Yang, B., Sun, M., Gan, G., Xu, C., Huang, Z., Zhang, H., & Fang, Z. Z. (2010). In situ Al2O3 particle-reinforced Al and Cu matrix composites synthesized by displacement reactions. Journal of Alloys and Compounds, 494(1-2), 261-265. https://doi.org/10.1016/j.jallcom.2010.01.005
7. Płonka, B., Żyłka, K., Remsak, K., Rajda, M., Zdunek, J., & Moszczyńska, D. (2023). Influence of copper content on the structure and properties of aluminium alloys. Archives of Civil and Mechanical Engineering, 24(8). https://doi.org/10.1007/s43452-023-00811-7
8. Gao, L., Li, K., Ni, S., Du, Y., & Song, M. (2021). The growth mechanisms of θ′ precipitate phase in an Al-Cu alloy during aging treatment. Journal of Materials Science & Technology, 61, 25-32. https://doi. org/10.1016/j.jmst.2020.05.046

9. Çavdar, U., Ulvi Gezici, L., Gül, B., & Ayvaz, M. (2020). Microstructural properties and tribological behaviours of Ultra-High frequency induction rapid sintered Al-WC composites. Revista de Metalurgia, 56(1), e163. https:// doi.org/10.3989/revmetalm.163
10. Ayvaz, M., Çavdar, U., Gül, B., & Gezici, L. U. (2020). Ultra-high frequency induction and conventional sintering of Al-SiO2 composites: A comparative study. Materials Testing, 62(10), 1048-1054. https://doi. org/10.3139/120.111582
11. Wang, Y., Liu, Q., Zhang, B., Zhang, H., Jin, Y., Zhong, Z., … & Wang, W. (2022). Dynamic mechanical response and damage mechanisms of nacre-inspired 2024Al/B4C composite at elevated temperature. Materials Science and Engineering: A, 831, 142263. https://doi.org/10.1016/j.msea.2021.142263
12. Ayvaz, M., & Cetinel, H. (2021). Mechanical properties of Al-Cu/B4C and Al-Mg/B4C metal matrix composites. Materials Testing, 63(4), 350-355. https://doi. org/10.1515/mt-2020-0052
13. Manohar, G., Pandey, K. M., & Maity, S. R. (2021). Effect of sintering mechanisms on mechanical properties of AA7075/B4C composite fabricated by powder metallurgy techniques. Ceramics International, 47(11), 15147-15154. https://doi.org/10.1016/j. ceramint.2021.02.073
14. Zalaoglu, D., & Übeyli, M. (2021). Influence of aging and annealing processes on the properties of TiB2 particulate reinforced aluminum composites produced by powder metallurgy. Metallic Materials, 59(1), 21-38. https://doi.org/10.4149/km_2021_1_21
15. Yang, S., Guo, Z., & Xia, M. (2018). Effect of TiB content on the properties of Al-TiB composites. Science of Sintering, 50(2), 237-244. https://doi.org/10.2298/ SOS1802237Y
16. Wu, C., Fang, P., Luo, G., Chen, F., Shen, Q., Zhang, L., & Lavernia, E. J. (2014). Effect of plasma activated sintering parameters on microstructure and mechanical properties of Al-7075/B4C composites. Journal of Alloys and Compounds, 615, 276-282. https://doi. org/10.1016/j.jallcom.2014.06.110
17. Zhang, P., Li, J., Wang, W., Tan, X., Xie, L., & Chen, X. (2020). Design, shielding mechanism and tensile property of a novel (B4C+6061Al)/Cf/6061Al laminar neutron-shielding composite. Vacuum, 177, 109383. https://doi.org/10.1016/j.vacuum.2020.109383
18. Toptan, F., Kerti, I., & Rocha, L. A. (2012). Reciprocal dry sliding wear behaviour of B4Cp reinforced aluminium alloy matrix composites. Wear, 290-291, 74- 85. https://doi.org/10.1016/j.wear.2012.05.007
19. Ayvaz, M. (2021). Microstructure and dry sliding wear behaviors of microwave-sintered Al-4.4Cu-0.7 Mg- 0.6Si-B4C/nGr hybrid bomposites. Transactions of the Indian Institute of Metals, 74, 1397-1408. https://doi. org/10.1007/s12666-021-02232-7
20. Li, C., Xia, X., Cai, J., Zhang, Z., Wang, J., Qian, Z., … & Dai, Y. (2023). Influence analysis of B4C content on the neutron shielding performance of B4C/Al. Radiation Physics and Chemistry, 204, 110684. https://doi. org/10.1016/j.radphyschem.2022.110684
21. Wu, Y., Cao, Y., Wu, Y., & Li, D. (2020). Neutron shielding performance of 3D-printed boron carbide PEEK composites. Materials, 13(10), 2314. https://doi. org/10.3390/ma13102314
22. Gökmen, U., Özkan, Z., Jamalgolzari, L. E., & Ocak, S. B. (2020). Investigation of radiation attenuation properties of Al-Cu matrix composites reinforced by different amount of B4C particles. Journal of Boron, 5(3), 124-130. https://doi.org/10.30728/boron.730354
23. Baradeswaran, A., & Perumal, A. E. (2014). Wear and mechanical characteristics of Al 7075/graphite composites. Composites Part B: Engineering, 56, 472- 476. https://doi.org/10.1016/j.compositesb.2013.08.073
24. Sharma, P., Paliwal, K., Garg, R. K., Sharma, S., & Khanduja, D. (2017). A study on wear behaviour of Al/6101/graphite composites. Journal of Asian Ceramic Societies, 5(1), 42-48. https://doi.org/10.1016/j. jascer.2016.12.007
25. Ravindran, P., Manisekar, K., Narayanasamy, P., Selvakumar, N., & Narayanasamy, R. (2012). Application of factorial techniques to study the wear of Al hybrid composites with graphite addition. Materials & Design, 39, 42-54. https://doi.org/10.1016/j. matdes.2012.02.013
26. Islak, S. (2019). Mechanical and corrosion properties of AlCu matrix hybrid composite materials. Science of Sintering, 51(1), 81-92. https://doi.org/10.2298/ SOS1901081I
27. Sharma, A., Garg, M., & Singh, S. (2015). Taguchi optimization of tribological properties of Al/Gr/B4C composite. Industrial Lubrication and Tribology, 67(4), 380-388. https://doi.org/10.1108/ILT-10-2014-0099
28. Pozdniakov, A. V., Lotfy, A., Qadir, A., Shalaby, E., Khomutov, M. G., Churyumov, A. Yu., & Zolotorevskiy, V. S. (2017). Development of Al-5Cu/B4C composites with low coefficient of thermal expansion for automotive application. Materials Science and Engineering: A, 688, 1-8. https://doi.org/10.1016/j.msea.2017.01.075
29. Gowrishankar, T. P., Manjunatha, L. H., & Sangmesh, B. (2020). Mechanical and wear behaviour of Al6061 reinforced with graphite and TiC hybrid MMC’s. Materials Research Innovations, 24(3), 179-185. https://doi.org/10.1080/14328917.2019.1628497
30. Ghasali, E., Alizadeh, M., Ebadzadeh, T., Pakseresht, A. H., & Rahbari, A. (2015). Investigation on microstructural and mechanical properties of B4C-aluminum matrix composites prepared by microwave sintering. Journal of Materials Research and Technology, 4(4), 411-415. https://doi.org/10.1016/j.jmrt.2015.02.005
31. Şi̇mşek, İ. (2019). The effect of B4C amount on wear behaviors of Al-graphite/B4C hybrid composites produced by mechanical alloying. Journal of Boron, 4(2), 100-106. https://doi.org/10.30728/boron.556707
32. Oghbaei, M., & Mirzaee, O. (2010). Microwave versus conventional sintering: A review of fundamentals, advantages and applications. Journal of Alloys and Compounds, 494(1-2), 175-189. https://doi. org/10.1016/j.jallcom.2010.01.068
33. Reddy, M. P., Shakoor, R. A., Parande, G., Manakari, V., Ubaid, F., Mohamed, A. M. A., & Gupta, M. (2017). Enhanced performance of nano-sized SiC reinforced Al metal matrix nanocomposites synthesized through microwave sintering and hot extrusion techniques. Progress in Natural Science: Materials International, 27(5), 606-614. https://doi.org/10.1016/j. pnsc.2017.08.015
34. Mattli, M. R., Shakoor, R. A., Matli, P. R., & Amer Mohamed, A. M. (2019). Microstructure and compressive behavior of Al-Y2O3 nanocomposites prepared by microwave-assisted mechanical alloying. Metals, 9(4), 414. https://doi.org/10.3390/met9040414
35. Manohar, G., Pandey, K. M., & Maity, S. R. (2021). Effect of microwave sintering on the microstructure and mechanical properties of AA7075/B4C/ZrC hybrid nano composite fabricated by powder metallurgy techniques. Ceramics International, 47(23), 32610-32618. https:// doi.org/10.1016/j.ceramint.2021.08.156
36. Manohar, G., Maity, S. R., & Pandey, K. M. (2022). Microstructural and mechanical properties of microwave sintered AA7075/Graphite/SiC hybrid composite fabricated by powder metallurgy techniques. Silicon, 14, 5179-5189. https://doi.org/10.1007/ s12633-021-01299-7
37. Bedir, F. (2007). Characteristic properties of Al-Cu- SiCp and Al-Cu-B4Cp composites produced by hot pressing method under nitrogen atmosphere. Materials & Design, 28(4), 1238-1244. https://doi.org/10.1016/j. matdes.2006.01.003
38. Çanakçı, A., Karabacak, A. H., Çelebi, M., Özkaya, S., & Arpacı, K. A. (2024). A study on the optimization of nano-B4C content for the best wear and corrosion properties of the Al-based hybrid nanocomposites. Arabian Journal for Science and Engineering, 49, 14625- 14641. https://doi.org/10.1007/s13369-024-08736-w
39. Çağlar, S., & Temiz, C. (2025). Al-5Cu-0.3Sc- B4C nanocomposites: Microstructural refinement, strengthening mechanisms, and corrosion behavior. Nanomaterials, 15(23), 1836. https://doi.org/10.3390/ nano15231836
40. Çelebi, M., Çanakçı, A., & Kütük, S. (2026). Influence of nano-sized ceramic reinforcement content on the powder characteristics and the mechanical, tribological, and corrosion properties of Al-based alloy nanocomposites. Coatings, 16(1), 143. https://doi. org/10.3390/coatings16010143
41. Gezici, L. U., Özer, E., Sarpkaya, İ., & Çavdar, U. (2022). The effect of SiC content on microstructural and tribological properties of sintered B4C and SiC reinforced Al-Cu-Mg-Si matrix hybrid composites. Materials Testing, 64(4), 502-512. https://doi. org/10.1515/mt-2021-2103
42. Yılmaz, T. A., Taşci, U., Gökmen, A. U., & Bostan, B. (2025). Investigation of wear and transverse rupture strength of AA2219/ZrO2/B4C hybrid composite materials prepared with 3D ball mixer and produced by spark plasma sintering. Composite Interfaces, 32(5), 689-712. https://doi.org/10.1080/09276440.2024.2434 808
43. Karamış, M. B., Cerit, A. A., Selçuk, B., & Nair, F. (2012). The effects of different ceramics size and volume fraction on wear behavior of Al matrix composites (for automobile cam material). Wear, 289, 73-81. https:// doi.org/10.1016/j.wear.2012.04.012
44. Soysal, T. (2021). A criterion to find crack-resistant aluminium alloys to avoid solidification cracking. Science and Technology of Welding and Joining, 26(2), 99-105. https://doi.org/10.1080/13621718.2020.18432 60
45. ASTM International. (2023). Standard test methods for density of compacted or sintered powder metallurgy (PM) products using Archimedes' principle (B0962-23). https://doi.org/10.1520/B0962-23
46. Degen, T., Sadki, M., Bron, E., König, U., & Nénert, G. (2014). The HighScore suite. Powder Diffraction, 29(S2), S13-S18. https://doi.org/10.1017/S0885715614000840
47. Zagorac, D., Müller, H., Ruehl, S., Zagorac, J., & Rehme, S. (2019). Recent developments in the Inorganic Crystal Structure Database: Theoretical crystal structure data and related features. Journal of Applied Crystallography, 52(5), 918-925. https://doi. org/10.1107/S160057671900997X
48. ASTM International. (2023). Standard test method for Brinell hardness of metallic materials (E10-23). https:// doi.org/10.1520/E0010-23
49. ASTM International. (2025). Standard test method for microindentation hardness of powder metallurgy (PM) materials (B933-25). https://doi.org/10.1520/B0933-25
50. ASTM International. (2023). Standard test method for wear and friction testing with a pin-on-disk or ball-on-disk apparatus (G99-23). https://doi.org/10.1520/ G0099-23
51. Poquillon, D., Lemaitre, J., Baco-Carles, V., Tailhades, P., & Lacaze, J. (2002). Cold compaction of iron powders-relations between powder morphology and mechanical properties Part I: Powder preparation and compaction. Powder Technology, 126(1), 65-74. https://doi.org/10.1016/S0032-5910(02)00034-7
52. Yaginuma, Y., Ozeki, Y., Kakizawa, M., Gomi, S.-I., & Watanabe, Y. (2007). Effects of powder flowability on die-fill properties in rotary compression. Journal of Drug Delivery Science and Technology, 17(3), 205-210. https://doi.org/10.1016/S1773-2247(07)50037-7
53. Varol, T., & Canakci, A. (2013). Effect of particle size and ratio of B4C reinforcement on properties and morphology of nanocrystalline Al2024-B4C composite powders. Powder Technology, 246, 462-472. https:// doi.org/10.1016/j.powtec.2013.05.048
54. Riahi, A. R., & Alpas, A. T. (2001). The role of tribo-layers on the sliding wear behavior of graphitic aluminum matrix composites. Wear, 251(1-12), 1396- 1407. https://doi.org/10.1016/S0043-1648(01)00796-7
55. Arif, S., Jamil, B., Naim Shaikh, M. B., Aziz, T., Ansari, A. H., & Khan, M. (2020). Characterization of surface morphology, wear performance and modelling of graphite reinforced aluminium hybrid composites. Engineering Science and Technology, an International Journal, 23(3), 674-690. https://doi.org/10.1016/j. jestch.2019.07.001
56. Bai, Y., Wagner, G., & Williams, C. B. (2017). Effect of particle size distribution on powder packing and sintering in binder jetting additive manufacturing of metals. Journal of Manufacturing Science and Engineering, 139(8), 081019. https://doi.org/10.1115/1.4036640
57. Özer, E., & Ayvaz, M. (2024). Dry tribological behaviour of microwave-assisted sintered AA2024 matrix hybrid composites reinforced by TiC/B4C/nano-graphite particles. Materials Testing, 66(2), 233-247. https://doi. org/10.1515/mt-2023-0248
58. Matli, P., Shakoor, R., Amer Mohamed, A., & Gupta, M. (2016). Microwave rapid sintering of Al-metal matrix composites: A review on the effect of reinforcements, microstructure and mechanical properties. Metals, 6(7), 143. https://doi.org/10.3390/met6070143
59. Matli, P. R., Fareeha, U., Shakoor, R. A., & Mohamed, A. M. A. (2018). A comparative study of structural and mechanical properties of Al-Cu composites prepared by vacuum and microwave sintering techniques. Journal of Materials Research and Technology, 7(2), 165-172. https://doi.org/10.1016/j.jmrt.2017.10.003
60. Diler, E. A., Ghiami, A., & Ipek, R. (2015). Effect of high ratio of reinforcement particle size to matrix powder size and volume fraction on microstructure, densification and tribological properties of SiCp reinforced metal matrix composites manufactured via hot pressing method. International Journal of Refractory Metals and Hard Materials, 52, 183-194. https://doi.org/10.1016/j. ijrmhm.2015.06.008
61. Akgümüş Gök, D., Bayraktar, C., & Hoşkun, M. (2024). A review on processing, mechanical and wear properties of Al matrix composites reinforced with Al2O3, SiC, B4C and MgO by powder metallurgy method. Journal of Materials Research and Technology, 31, 1132-1150. https://doi.org/10.1016/j.jmrt.2024.06.110
62. Akhlaghi, F., & Pelaseyyed, S. (2004). Characterization of aluminum/graphite particulate composites synthesized using a novel method termed “in-situ powder metallurgy”. Materials Science and Engineering A, 385(1-2), 258-266. https://doi.org/10.1016/ S0921-5093(04)00876-7
63. Li, C., Wang, Y., Xu, L., Liu, Y., Lu, N., & Mi, G. (2020). Microstructure and mechanical property of compact graphite/6061Al composite prepared by ultra-high pressure sintering. Applied Sciences, 10(15), 5107. https://doi.org/10.3390/app10155107
64. Wang, Z. J., Zheng, Z., & Fu, M. W. (2024). Aluminum matrix composites: Structural design and microstructure evolution in the deformation process. Journal of Materials Research and Technology, 30, 3724-3754. https://doi.org/10.1016/j.jmrt.2024.03.237
65. De Castro, C. L., & Mitchell, B. S. (2002). The use of polymeric milling media in the reduction of contamination during mechanical attrition. Journal of Materials Research, 17, 2997-2999. https://doi. org/10.1557/JMR.2002.0434
66. Özer, E., Ayvaz, M., Übeyli, M., & Sarpkaya, İ. (2023). Properties of aluminum nano composites bearing alumina particles and multiwall carbon nanotubes manufactured by mechanical alloying and microwave sintering. Metals and Materials International, 29, 402- 419. https://doi.org/10.1007/s12540-022-01238-0
67. Jeon, J., Lee, S., Jeon, J., Kang, M., & Kang, H. (2024). Effect of Al7Cu2Fe particles on the anisotropic mechanical properties and formability of Al-Zn-Mg-Cu-based alloy sheets. Materials, 17(23), 5924. https://doi. org/10.3390/ma17235924
68. Kim, Y.-W., Griffith, W. M., & Froes, F. H. (1985). Surface oxides in P/M aluminum alloys. JOM, 37, 27- 33. https://doi.org/10.1007/BF03257675
69. Zobac, O., Kroupa, A., Zemanova, A., & Richter, K. W. (2019). Experimental description of the Al-Cu binary phase diagram. Metallurgical and Materials Transactions A, 50, 3805-3815. https://doi.org/10.1007/ s11661-019-05286-x
70. Andersen, S. J., Marioara, C. D., Friis, J., Wenner, S., & Holmestad, R. (2018). Precipitates in aluminium alloys. Advances in Physics: X, 3(1), 1479984. https://doi.org/ 10.1080/23746149.2018.1479984
71. Ozdemir, F., Witharamage, C. S., Christudasjustus, J., Darwish, Aa., Okuyucu, H., & Gupta, R. K. (2022). Corrosion behavior of a bulk nanocrystalline Al-Fe alloy. Corrosion Science, 209, 110727. https://doi. org/10.1016/j.corsci.2022.110727
72. Gökmeşe, H., & Karadağ, H. B. (2018). Examination of microstructure and mechanical properties of powder metal AA 2014-SiC-B4C composite / hybrid materials. Gazi University Journal of Science Part C: Design and Technology, 6(2), 385-398. https://doi.org/10.29109/ http-gujsc-gazi-edu-tr.364857
73. Varol, T., Çanakçı, A., Özşahin, Ş., Beder, M., & Akçay, S. B. (2024). Prediction of effect of fabrication parameters on the properties of B4C ceramic particle reinforced AA2024 matrix nanocomposites using neural networks. Materials Today Communications, 39, 109279. https:// doi.org/10.1016/j.mtcomm.2024.109279
74. Topcu, I., Gulsoy, H. O., Kadioglu, N., & Gulluoglu, A. N. (2009). Processing and mechanical properties of B4C reinforced Al matrix composites. Journal of Alloys and Compounds, 482(1-2), 516-521. https://doi. org/10.1016/j.jallcom.2009.04.065
75. Hasan, L. K., Jiaad, S. M., Salman, K. D., Al-Maliki, W. A. K., Alobaid, F., & Epple, B. (2023). Wear characteristics of (Al/B4C and Al/TiC) nanocomposites synthesized via powder metallurgy method. Applied Sciences, 13(23), 12939. https://doi.org/10.3390/app132312939
76. Karabacak, A. H., Çanakçı, A., Erdemir, F., Özkaya, S., & Çelebi, M. (2022). Corrosion and mechanical properties of novel AA2024 matrix hybrid nanocomposites reinforced with B4C and SiC particles. Silicon, 14, 8567- 8579. https://doi.org/10.1007/s12633-021-01582-7
77. Zhang, L., Wang, Z., Li, Q., Wu, J., Shi, G., Qi, F., & Zhou, X. (2018). Microtopography and mechanical properties of vacuum hot pressing Al/B4C composites. Ceramics International, 44(3), 3048-3055. https://doi. org/10.1016/j.ceramint.2017.11.065
78. Basar, G., Kahraman, F., & Der, O. (2025). Multi-response optimization of drilling parameters in direct hot-pressed Al/B4C/SiC hybrid composites using Taguchi-based Entropy-CoCoSo method. Materials, 18(18), 4319. https://doi.org/10.3390/ma18184319
79. Karabacak, A. H., & Çanakçı, A. (2023). Investigation of mechanical and corrosion properties of different ceramic reinforced Al alloy matrix nanocomposites. The Black Sea Journal of Sciences, 13(1), 1-14. https://doi. org/10.31466/kfbd.1085130
80. Çelebi, M., Çanakçı, A., & Özkaya, S. (2025). Effect of mechanical milling time on powder characteristic, microstructure, and mechanical properties of AA2024/B4C/GNPs hybrid nanocomposites. Powder Technology, 449, 120439. https://doi.org/10.1016/j. powtec.2024.120439
81. Beder, M. (2025). The effect of high B4C ratio on the improvement of mechanical properties and wear resistance of Al2024/B4C composites fabricated by mechanical milling-assisted hot pressing. Ceramics International, 51(7), 9528-9547. https://doi. org/10.1016/j.ceramint.2025.01.287
82. Basavarajappa, S., Chandramohan, G., Mukund, K., Ashwin, M., & Prabu, M. (2006). Dry sliding wear behavior of Al 2219/SiCp-Gr hybrid metal matrix composites. Journal of Materials Engineering and Performance, 15, 668-674. https://doi.org/10.1361/105994906X150803
83. Şahin, S., Yüksel, N., Durmuş, H., & Gençalp İrizalp, S. (2014). Wear Behavior of Al/SiC/Graphite and Al/FeB/ Graphite Hybrid Composites. Materiali in Tehnologije, 48(5), 639-646