GENİŞLEYEBİLEN POLİSTİREN KÖPÜK ÜRETİMİNDE KALIPLAMA PARAMETRELERİNİN TANE KAYNAMASI VE AĞIRLIĞA ETKİSİNİN İNCELENMESİ

Öz

Bu çalışmada, genişleyebilen polistiren (GPS) köpük üretiminde kalıplama basıncı ve sürelerinin kalıplama sonrası ağırlık değişimi ve tane kaynaması üzerine etkisi incelenmiştir. Deneysel çalışmalarda değişik kalıplama basıncı (1, 1,1 ve 1,2 atm) ve kalıplama süreleri (20, 30 ve 40 s)  kullanılarak ASTM D638 standardına göre polistiren numuneler üretilmiş ve bu numunelerin doğal yaşlandırması oda sıcaklığında 720 saat (30 gün) süre ile gerçekleştirilmiştir. Deneysel sonuçlar, polistiren köpük numunelerin doğal yaşlandırma işleminde ağırlık kaybının %99’nu 24 saat sürede gerçekleştirdiğini ve 720 saat sürede ise tamamlandığını göstermiştir. Kalıplama basıncı ve süresi arttıkça kalıplama sonrası ağırlık değişimleri azalmıştır. Polistiren köpük numunelerde 20 s kalıplama süresi 1 ve 1,1 atm kalıplama basınçlarında yeterli derecede tane kaynamasını sağlamazken 30 ve 40 s kalıplama süreleri yüksek derecede tane kaynaması üretmiştir. Kalıplama sonrası ağırlık değişimi arttıkça kaynama derecesinin düştüğü belirlenmiştir.

Anahtar Kelimeler

• GPS, Tane kaynaması, Kaybolan köpük

THE EFFECT OF MOLDING DENSITY ON THE BEAD FUSION AND WEIGHT IN THE EXPANDABLE POLYSTYRENE PRODUCTION

Abstract

In this study, the effect of molding times and pressures on weight change after molding and the bead fusion was investigated in the production of expandable polystyrene (EPS) foam. In experimental studies, polystyrene samples were produced using various molding pressures (1, 1.1 and 1.2 atm) and molding times (20, 30 and 40 sec) according to ASTM D638 standard and natural aging of these samples were carried out at room temperature for 720 hours (30 days). Experimental results showed that in the natural aging process of EPS foam 99% of losses of sample weight was performed approximately with 24 hours time, and was completed with 720 hours time. The weight change after molding was decreased with increasing molding pressure and time. While 20 sec molding time with the molding pressures of 1 and 1.1 atm did not provide sufficient bead fusion, the 30 and 40 sec molding times were produced high degree of bead fusion. It was determined that the fusion degree was decreased with increasing the weight change after molding.

Keywords

• EPS, Bead fusion, Lost foam

Kaynakça

1. Rossacci, J., Shivkumar, S., (2003). Bead Fusion in Polystyrene Foam, Journal of Materials Science, 38, 201-206.
2. Saçak, M., (2012). Polimer Teknolojisi, Gazi Kitapevi, 2.Baskı, Ankara, 349-366.
3. Bates, C.E., Littleton, H.E., McMellon, B., Stroom, P.A., (2001). Technological Developments and Woldwide Market Growth in Lost Foam Casting Production, AFS Transaction, 109: 1557-1572.
4. Yalçın, N., (2006). Köpük Model Döküm Yönteminde Döküm ve Model Parametrelerinin İncelenmesi, Doktora Tezi, Gazi Üniversitesi, Fen Bilimleri Enstitüsü.
5. Rossacci, J., Shivkumar, S., (2003). Influence of EPS Bead Fusion on Pattern Degradation and Casting Formation in the Lost Foam Process, Journal of Materials Science, 38, 2321-2330.
6. Sands, M., Shivkumar, S., (2003). EPS Molecular Weight and Foam Density Effect in The Lost Foam Process, Journal of Materials Science, 38, 2233-2239.
7. Brydson, J.A., (1989). Plastics materials, Butterworth and Heinemann, 5 th Edition, London, 406-431.
8. Gutierrez, C., et.al., (2014). Preparation and Characterization of Polystyrene Foams from Limonene Solutions, The Journal of Supercritical Fluids, 88, 92-104.

9. Sands, M., Shivkumar, S., (2003). Influence of Coating Thickness and Sand Fineness on Mold Filling in The Lost Foam Casting Process, Journal of Materials Science, 38, 6676
10. Littleton,H.E., et.all, (1996). Lost Foam Casting- Process Control for Precision, AFS Transactions, 104, 335-346.
11. Shivkumar, S., Wang, L., Steenhoff, B., (1989). Metallurgical Quality of Aluminum Castings Produced by the Lost Foam Process, AFS Transactions, 97, 825-836.
12. Khodai, M., Parvin, N., (2008). Pressure Measurement and Some Observation in Lost Foam Casting, Journal of Materials Processing Technology, 206, 1-6.
13. Kannan, P., Biernacki, J.J., Visco, D.P., (2007). A Review of Physical and Kinetically Models of Thermal Degradation of Expanded Polystyrene Foam and Their Application to the Lost Foam Casting Process, Journal of Analytical and Applied Pyrolysis, 78, 162-171. Caulk, D.A., (2006). A Foam Melting Model for Lost Foam Casting of Aluminum, International Journal of Heat and Mass Transfer, 49, 2124-2136.
14. Sands, M., Shivkumar, S., (2006). EPS Bead Fusion Effects on Defect Formation in Lost Foam Casting of Aluminum Alloys, Journal of Materials Science, 41, 2373-2379.