A Novel Glow Plug Design to Improve Heating Capability via Induction Heating

Öz

Glow plug is a simple method to improve cold start for diesel engines, especially for cold weather and conditions. In cold or iced weather conditions, diesel engines cannot reach the ignition temperature just compressing the air. Thus, heated air must be added to combustion chamber before the compressing via external device such as glow plug. Glow plug helps engine regulate the first starting and leads to obtain low emission during the cold starting or up to warm up the engine due to its controllability. Although glow plug installing is easy way to improve heat air obtaining, glow plugs have some limitations. Major problem, generated heat inside the glow plug starts from inside to outside. Thus, it takes time to obtain heated air. During the extremely cold weather conditions, one cycle not enough for heating. So, temperature of air is another major factor reducing the glow plug affect. On the contrary, induction heating is fast and efficient method and could be acceptable new generation method compared the resistive heating. Induction heating is based on hysteresis losses at high frequency switching. Induction heating has strong affect on iron based materials which has large hysteresis are. Our method is based on induction heating using 368 kHz switching frequency to improve heating capability. In addition to resistive heating, induction heating increases the heat volume. Moreover, induction heating effects the cover of the glow plug, thus improve method has no destructive affect on the core of glow plug because the surface heating.

Anahtar Kelimeler

• Glow plug,induction heating,high frequency,cold start,cold weather condition,oscillator circuit

Kaynakça

1. Benson, Rowland S., and Norman Dan Whitehouse. Internal combustion engines: a detailed introduction to the thermodynamics of spark and compression ignition engines, their design and development. Vol. 1. Elsevier, 2013.
2. Labeckas, Gvidonas, and Stasys Slavinskas. "The effect of rapeseed oil methyl ester on direct injection diesel engine performance and exhaust emissions." Energy Conversion and Management 47.13 (2006): 1954-1967.
3. Payri, F., et al. "Investigation of Diesel combustion using multiple injection strategies for idling after cold start of passenger-car engines." Experimental Thermal and Fluid Science 34.7 (2010): 857-865.
4. Weidmann, Kurt, and Holger Menrad. Fleet test, performance and emissions of diesel engines using different alcohol-diesel fuel blends. No. 841331. SAE Technical Paper, 1984.
5. Gotoh, Shunsuke, et al. "Controller and glow plug for controlling energization modes." U.S. Patent No. 7,319,208. 15 Jan. 2008.
6. Li, Bob X., and Brian K. Allston. "Method for controlling glow plug ignition in a preheater of a hydrocarbon reformer." U.S. Patent No. 8,183,501. 22 May 2012.
7. M. G. Lozinskii, Industrial Applications of Induction Heating, [1st English ed. Oxford, New York,: Pergamon Press, 1969.
8. W. C. Moreland, "The induction range: its performance and its development problems," IEEE Transactions on Industry Applications, vol. 9, no. 1, pp. 81-85, Jan./Feb. 1973.

9. P. R. Stauffer, T. C. Cetas, and R. C. Jones, "Magnetic Induction Heating of Ferromagnetic Implants for Inducing Localized Hyperthermia in Deep-Seated Tumors," IEEE Transactions on Biomedical Engineering, vol. BME-31, no. 2, pp. 235-251, February 1984.
10. G. H. Brown, C. N. Hoyler, and R. A. Bierwirth, Theory and Application of Radio-Frequency Heating. New York,: Van Nostrand, 1947.
11. J. W. Cable, Induction and Dielectric Heating. New York,: Reinhold, 1954.
12. V. Rudnev, D. Loveless, R. Cook, and M. Black, Handbook of induction heating. New York: Marcel Dekker Inc., 2003.
13. J. Davies, Conduction and Induction heating. London: Peter Peregrinus Ltd., 1990.
14. A. Mühlbauer, History of Induction Heating and Melting. Essen: Vulkan-Verlag GmbH, 2008.
15. V. Esteve, et al., "Improving the efficiency of IGBT series-resonant inverters using pulse density modulation," IEEE Transactions on Industrial Electronics, vol. 58, no. 3, pp. 979-987, March 2011.
16. Sondheimer, E. Hi. "The mean free path of electrons in metals." Advances in physics 1.1 (1952): 1-42.
17. Sondheimer, E. H. "The mean free path of electrons in metals." Advances in Physics 50.6 (2001): 499-537.
18. Gutfleisch, Oliver, et al. "Magnetic materials and devices for the 21st century: stronger, lighter, and more energy efficient." Advanced materials 23.7 (2011): 821-842.
19. Persson, M., et al. "Soft magnetic composite materials-use for electrical machines." Electrical Machines and Drives, 1995. Seventh International Conference on. IET, 1995.
20. McLyman, Colonel William T. Transformer and inductor design handbook. Vol. 121. New York, NY, USA:: Marcel Dekker, 2004.
21. Hua, Guichao, et al. "Novel zero-voltage-transition PWM converters." IEEE transactions on Power Electronics 9.2 (1994): 213-219.
22. Stewart Xu Cheng and James S. Wallace, Transient Behaviour of Glow Plugs in Direct Injection Natural Gas Engines, 2012.
23. John M. Bailey, Carey A. Towe, Scott F. Shafer, Michael M. Blanco, Encapsulated Heating Filament for Glow Plug, 1992.