Investigation on hydrodynamic characteristics of a Stirling regenerator matrix using porous media approach: a CFD study

Yıl 2020, Cilt: 9 Sayı: 4, 171 - 177, 31.12.2020

Duygu İpci

https://doi.org/10.18245/ijaet.779636

Cited By: 1

Öz

In this study, hydrodynamic characteristics of a Stirling regenerator matrix are predicted by porous medium based modeling. A regenerator is designed to be used in the beta type Stirling engine. CFD analysis of the designed regenerator is performed by the ANSYS Fluent software with porous media model. The flow properties in porous media are generally approximated by Forchheimer or Ergun flow regime. The equation of the Forchheimer flow model consists of two-term: viscous loss and the inertial loss. The viscous resistance and inertial resistance factors of the porous medium to be used in CFD analysis is determined from published experimental results for a regenerator made by stainless steel with the porosity of 70 %. The CFD simulation are validated by comparing the calculated the velocity distributions at the exit of the regenerator with results of previously published paper. By using both resistance factors, pressure drops, and friction factors of the regenerator matrix are calculated via CFD analysis. The friction results are interpolated to generate a correlation equation that can be able to calculate the pressure drops in the flow direction of the regenerator and to use in future numerical simulations.

Anahtar Kelimeler

Stirling engine regenerator, porous media, pressure drop, friction factor

Kaynakça

• D. Beck, and D. G. Wilson, “Gas-turbine regenerators”, Springer Science & Business Media, 2012.
• K. Yanaga, “Experimental and Numerical Study of the Stirling Engine Robust Foil Regenerator”, Graduate Theses, Dissertations, and Problem Reports, 7401, 2019.
• M. Tanaka, I. Yamashita, F. Chisaka, “Flow and heat transfer characteristics of Stirling engine regenerator in oscillating flow”, Trans. Japan Soc. Mech. Eng., Ser. B, 55, 2478-2485, 1989.
• P. Puech, V. Tishkova, “Thermodynamic analysis of a Stirling engine including regenerator dead volume”, Renewable Energy, 36(2), 872-878, 2011.
• S. K. Andersen, H. Carlsen, P. G. Thomsen, “Numerical study on optimal Stirling engine regenerator matrix designs taking into account the effects of matrix temperature oscillations”, Energy Conversion and Management, 47(7-8), 894-908, 2006.
• R. Gheith, F. Aloui and S. B. Nasrallah, “Determination of adequate regenerator for a Gamma-type Stirling engine”, Applied Energy, 139, 272-280, 2015.
• Z. S. Yuan, “Oscillatory flow and heat transfer in a Stirling engine regenerator”, Doctoral dissertation, Case Western Reserve University, 1993.
• M. C. Shin, J. A. and B. H. Kang, “Performance characteristics of a regenerative heat exchanger depending on its porous structure”, Korean J. of Air-Conditioning and Refrigeration Engineering, 24 (6), 487-496, 2012.
• M. Arab, and M. Majidi, “Experimental and numerical study of porosity gradient in a Stirling engine regenerator” (No. 2017-01-0148), SAE Technical Paper, 2017.
• W. L. Chen, K. L. Wong, H. E. Chen, “An experimental study on the performance of the moving regenerator for a γ-type twin power piston Stirling engine”, Energy Conversion and Management, 77, 118-128, 2014.
• S. C. Costa, H. Barrutia, J. A. Esnaola, M. Tutar, “Numerical study of the heat transfer in wound woven wire matrix of a Stirling regenerator”, Energy Conversion and Management, 79, 255-264, 2014.
• S. C. Costa, M. Tutar, I. Barreno, J. A. Esnaola, H. Barrutia, D. García, M. A. Gonzalez, J. I. Prieto, “Experimental and numerical flow investigation of Stirling engine regenerator”, Energy, 72, 800-812, 2014.
• B. G. Kim, W. S. Park, B. G. Koo, S. Park, “Effects of regenerator structure on performance of free piston Stirling engine (FPSE)”, Journal of Mechanical Science and Technology, 32(9), 4473-4484, 2018.
• M. A. Mohammadi, and A.Jafarian, “CFD simulation to investigate hydrodynamics of oscillating flow in a beta-type Stirling engine”, Energy, 153, 287-300, 2018.
• D. Gedeon, and J. G. Wood, “Oscillating-flow regenerator test rig: hardware and theory with derived correlations for screens and felts”, NASA CR-198442, 6-13, 1996.
• Yamashita, and K. Hamaguchi, “Effect of entrance and exit areas on the pressure drop and velocity distribution in regenerator matrix”, JSME International Journal Series B Fluids and Thermal Engineering, 42(3), 498-505, 1999.
• Y. Su, and J. H. Davidson, “Modeling approaches to natural convection in porous media”, United States of America: Springer, 2015.
• B. Çetin, K. G. Güler, and M. H. Aksel, “Computational modelling of vehicle radiators using prous medium approach. In Heat Exchanger Design, Experiment and Simulation”, Chapter 11, INTECH, 2017.
• D. A. Nield, and A. Bejan, “Convection in porous media”, Volume 3. Springer, New York, 2006.
• Vafai, K. Handbook of porous media. CRC Press, 2015.