The Effect of Different Mppt on the Linear Load and Non-Linear Load in Pv System

Öz

The output power of a PV array is dependent on environmental factors such as solar irradiation and temperature. So, it has a non-linear I-V characteristic. Maximum Power Point (MPP) is a point on the I-V, P-V characteristic curve of a PV array where the PV device generates maximum output power. The location of MPP shifts as the climate changes. MPPT's aim is to keep the solar operating voltage as similar to MPP as possible under changing environmental conditions. They must run at their MPPT considering the inhomogeneous shift in environmental conditions in order to continuously gather the full power from the PV array. Here the most commonly used MPPT algorithms for PV applications are illustrated because they are easy to implement which are Perturb and Observe (P&O), Hill Climbing (HC) and Incremental Conductance (INC). In this paper, the applications of those three MPPT algorithms in PV systems at linear and nonlinear loads have been investigated. Comparative analysis

Anahtar Kelimeler

• MPPT
• PV System
• linear load
• non-linear load
• MPPT, PV System, linear load, non-linear load,

Kaynakça

1. [1] G. P. G. S. M. V. N. Femia, "Optimizing sampling rate of P&O MPPT," in Proc. IEEE PESC, pp. 1945- 1949, 2004.
2. [2] L.-W. L. Huang-Jen Chiu, "A Bidirectional DC–DC Converter for Fuel Cell Electric Vehicle Driving System," IEEE TRANSACTIONS ON POWER ELECTRONICS, Vols. VOL. 21, NO. 4, pp. 950-959, JULY 2006.
3. [.3 K] . B. U. S. V. D. D. P. Jacob James Nedumgatt, "Perturb and Observe MPPT Algorithm for Solar PV Systems-Modeling and Simulation," researchgate, December 2011.
4. [4] High Step-Up Gain DC-DC Converter with Switched Capacitor and Regenerative Boost Configuration for Solar PV Applications.
5. [5] Analysis of DC/DC Boost Converters Design Methods Dr. Stephan Bayne 2015
6. [6] Freris, L. and D. Infield, Renewable energy in power systems. 2008: John Wiley & Sons..
7. [7] Boost Converter Design and Analysis for Photovoltaic Systems YavuzBahadır KOCA1– Yılmaz ASLAN2 – Ahmet YÖNETKEN3 – Yüksel OĞUZ4,*.
8. [8] CCM and DCM operation of the integrated-magnetic interleaved two-phase boost converter.

9. [9] DESIGN, SIMULATION AND IMPLEMENTATION OF A HIGH STEP-UP Arash torkan 2016.
10. [10] Boost Converter Design and Analysis for Photovoltaic Systems.
11. [11] Mechanical Sun-Tracking Technique Implemented for Maximum Power Point Tracking of a PV System for Effective Energy Supply - Scientific Figure on ResearchGate. Available from: https://www.researchgate.net/figure/MPPT-at-different-irradiance-for-I-V-P-V-of- PV-panel-at-constant-temp-of-25-o-C_fig1_285400008
12. [12] Awang JUSOH, Rozana ALIK, Tan Kar GUAN, Tole SUTIKNO "MPPT for PV System Based on Variable Step Size P&O Algorithm" TELKOMNIKA, Vols. VOL. 15, NO. 1, p.84 , MARCH 2017.
13. [13] Design of Hybrid Solar Wind Energy System in a Microgrid with MPPT Techiques - Scientific Figure on ResearchGate. Available from: https://www.researchgate.net/figure/Flowchart-of-P-O-MPPT-algorithm_fig1_323720840
14. [14] PSIM and MATLAB Co-Simulation of Photovoltaic System using “P and O” and “Incremental Conductance” MPPT - Scientific Figure on ResearchGate. Available from: https://www.researchgate.net/figure/flowchart-of-Incremental-Conductancealgorithm_ fig5_307598655