Consolidation of Rapidly Solidifying Al-6Si-0.3Cu Alloy by Spark Plasma Sintering and Cold Compaction Methods

Öz

In this study, Al-6Si-0.3Cu ribbon alloys produced by melt-spinning method were consolidated by two different methods, which are spark plasma sintering and cryogenic ball milling + cold compaction. From X-ray diffraction analysis, it was found that the solubility of Si in Al matrix in melt-spun alloys increased, but Si precipitated in SPS and ball milled+cold compacted alloys. Optical and scanning electron microscope observation revealed that while melt spun alloys have a very fine and homogenous microstructure, Si phase has become coarser in SPS and cold compacted alloys due to the sintering. The results showed that the spark plasma sintering method is a very effective method for compaction of melt-spun Al-6Si-0.3Cu alloy.

Anahtar Kelimeler

• Al-6Si-0.3Cu alloy
• melt-spinning
• spark plasma sintering
• cryogenic milling
• cold compaction

Kaynakça

1. [1] O. Uzun, F. Yilmaz, U. Kolemen, N. Basman, “Sb effect on micro structural and mechanical properties of rapidly solidified Al-12Si alloy”, Journal of Alloys and Compounds, vol. 509, issue 1, pp. 21-26, 2011.
2. [2] C. Temiz, F. Yilmaz, U. Kolemen, “Investigation of microstructures and mechanical properties of Sc doped Al-5Cu alloys”, Journal of the Faculty of Engineering and Architecture of Gazi University, vol. 37, issue 1, pp. 75-88, 2022.
3. [3] O. Uzun, F. Yilmaz, C. Emeksiz, S. Ergen, U. Kolemen, “Correlation of hardness and silicon morphology for Al-Si-Sb alloy”, Archives of Metallurgy and Materials, vol. 63, issue 1, pp. 467-472, 2018.
4. [4] R. Oin, R.F. Yan, Z.P. Guan, G.Q. Zhang, J.W. Song, W. Ren, J.G. Wang, “Effect of vanadium on Fe-rich phase, mechanical properties and thermal conductivity of hypoeutectic Al–Si alloy”, Materials Research Express, vol. 8, pp. 026518, 2021.
5. [5] F. Mao, Y. Qiao, P. Zhang, C. Chen, C. Zhang, “Modification mechanism of rare earth Eu on eutectic Si in hypoeutectic Al-Si alloy”, vol. 16, issue 2, pp. 634-645, 2022.
6. [6] M.F. Kilicaslan, F. Yilmaz, S.J. Hong, O. Uzun, “Effect of Co on Si and Fe-containing intermetallic compounds (IMCs)in Al–20Si–5Fe alloys”, Materials Science and Engineering A, vol. 556, pp. 716-721, 2012.
7. [7] W.K. Kang, F. Yılmaz, H.S. Kim, J.M. Koo, S.J. Hong, “Fabrication of Al–20 wt%Si powder using scrap Si by ultra-high-energymilling process”, Journal of Alloys and Compounds, vol. 536S, pp. 45-49, 2012.
8. [8] W. Ding, L. Gou, L. Hu, H. Zhang, W. Zhao, J. Ma, J. Qiao, X. Li, “Modification of eutectic Si in hypoeutectic Al-Si alloy with novel Al-3Ti-4.35La master alloy”, Journal of Alloys and Compounds, vol. 929, pp.167350, 2022.

9. [9] M.F. Kilicaslan, F. Yilmaz, S. Ergen, S.J. Hong, O. Uzun, “Microstructure and microhardness of melt-spun Al-25Si-5Fe-XCo (X=0, 1, 3, 5) alloys”, Materials Characterization, vol. 77, pp. 15-22, 2013.
10. [10] S. Ergen, O. Uzun, F. Yilmaz, M.F. Kilicaslan, “Shape memory properties and microstructural evolution of rapidly solidified CuAlBe alloys”, Materials Characterization, vol. 80, pp. 92-97, 2013.
11. [11] D. Yim, P. Sathiyamoorthi, S.J. Hong, H.S. Kim, “Fabrication and mechanical properties of TiC reinforced CoCrFeMnNi high-entropy alloy composite by water atomization and spark plasma sintering”, vol. 781, pp. 389-396, 2019.
12. [12] Z. Chen, Y. Lei, H. Zhang, “Structure and properties of nanostructured A357 alloy produced by meltspinning compared with direct chill ingot”, vol. 509, pp. 7473-7479, 2011.
13. [13] X. Zhang, L. Li, Z. Peng, J. Gao, “Microstructure and mechanical properties of an Al-11La-6Mgalloy prepared by the melt spinning and spark plasma sintering”, Journal of Physics: Conference Series, vol. 2044, pp. 012099, 2021.
14. [14] E.M. Ahmet, M.R. Ebrahim, “Microstructure and microhardness evolution of melt-spunAl-Si-Cu alloy”, The European Physical Journal Plus, vol. 129, pp. 60-68, 2014.
15. [15] E.M. Ahmed, “THE INFLUENCE OF RAPID SOLIDIFICATION ON THE PHYSICALPROPERTIES OF Al-Mn-Ce-Sb ALLOYS”, Asian Journal of Physical Sciences, vol. 1, pp. 1-9, 2012.