Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics

Cilt: 2 Sayı: 2 1 Haziran 2012
  • Apratim Roy
PDF İndir
EN

Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics

Abstract

In this paper, a novel method to derive surface roughness for the location of a wind-turbine facility is explained. Employing measured and projected low altitude (~10-30m) meteorological data, wind shear coefficients are estimated for weather stations in Bangladesh with potential for harnessing wind energy. Diversely located geographical positions are covered from three national sectors on the basis of surveys conducted by the United Nations. Time-series (annual and monthly) variation of wind shear is exploited to produce a forecasting tool for wind profile at commercial turbine heights. Best estimates of average shear factors (in the range of 0.1 to 0.3) are obtained from probability distribution curves and by matching their profiles with forecasted wind curves, roughness length is determined for specific weather points. The findings (varying from 0.05 to 0.5) are used to derive range of obtainable capacity factors (18 to 37%) for medium-scale installed turbines. The proposed method is expected to provide accurate projections of logarithmic wind power law and achievable turbine efficiency in potential wind centers of Bangladesh.

Keywords

Kaynakça

  1. D. Talbot, Lifeline for renewable power, Technol. Rev., vol. 112, no. 1, pp. 40-47, 2009.
  2. F. M. Hughes, O. Anaya-Lara, N. Jenkins, and G. Strbac, ”Control of DFIG-based wind generation for power network support,” IEEE Trans. Power Syst., vol. 20, no. , pp. 1958-1966, Nov. 2005.
  3. Danish Wind Industry Association Statistics, [online], Available:http://www.windpower.org/en/knowledge/stati stics/. Rod Frehlich, ”Measurements of Wind and Turbulence Profiles With Scanning Doppler Lidar for Wind Energy Applications”, IEEE Journal of Selected Topics in Applied Earth Observations And Remote Sensing, Vol. 1, No. 1, pp. 42-47, March 2008.
  4. E. A. Peterson, ”On the Estimates of Power Laws for Estimates of Wind Power Potential,” Journal of Applied Meteorology, Vol. 17, Oct. 1977, pp. 390-394.
  5. E. A. Peterson, ”A study of wind and temperature data from the 123m tower at Riso, Denmark,” Journal of Royal Meteorological Society, Vol. 102, 1975, pp. 857
  6. M. R. Milligan, Modelling utility-scale wind power plants. Part 1: Economics, Wind Energy, vol. 2, pp. , 1999. Official Website of Information and Environmental http://www.reein.org/ Network (REEIN):
  7. Official Website of Bangladesh Power Development Board http://www.bpdb.gov.bd/. Online]. Available: Official Website of Rural Electrification Board (REB), Bangladesh: http://www.reb.gov.bd/ Renewable Energy Research Center (RERC), University of Dhaka, Solar and Wind Energy Resource Assessment (SWERA) - Bangladesh project, Feb. 2007.
  8. A. Roy, ”Assessment of Commercial Wind Profiles for Bangladesh in Hotspots Determined by the UNEP”, International Jnl. of Renewable Energy Research, vol. 1, no. 4, pp. 290-297, Dec. 2011.

Ayrıntılar

Birincil Dil

İngilizce

Konular

-

Bölüm

-

Yazarlar

Apratim Roy Bu kişi benim

Yayımlanma Tarihi

1 Haziran 2012

Gönderilme Tarihi

3 Şubat 2016

Kabul Tarihi

-

Yayımlandığı Sayı

Yıl 2012 Cilt: 2 Sayı: 2

Kaynak Göster

APA
Roy, A. (2012). Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics. International Journal Of Renewable Energy Research, 2(2), 348-355. https://izlik.org/JA62PT55WX
AMA
1.Roy A. Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics. International Journal Of Renewable Energy Research. 2012;2(2):348-355. https://izlik.org/JA62PT55WX
Chicago
Roy, Apratim. 2012. “Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics”. International Journal Of Renewable Energy Research 2 (2): 348-55. https://izlik.org/JA62PT55WX.
EndNote
Roy A (01 Haziran 2012) Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics. International Journal Of Renewable Energy Research 2 2 348–355.
IEEE
[1]A. Roy, “Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics”, International Journal Of Renewable Energy Research, c. 2, sy 2, ss. 348–355, Haz. 2012, [çevrimiçi]. Erişim adresi: https://izlik.org/JA62PT55WX
ISNAD
Roy, Apratim. “Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics”. International Journal Of Renewable Energy Research 2/2 (01 Haziran 2012): 348-355. https://izlik.org/JA62PT55WX.
JAMA
1.Roy A. Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics. International Journal Of Renewable Energy Research. 2012;2:348–355.
MLA
Roy, Apratim. “Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics”. International Journal Of Renewable Energy Research, c. 2, sy 2, Haziran 2012, ss. 348-55, https://izlik.org/JA62PT55WX.
Vancouver
1.Apratim Roy. Derivation of Surface Roughness and Capacity Factor from Wind Shear Characteristics. International Journal Of Renewable Energy Research [Internet]. 01 Haziran 2012;2(2):348-55. Erişim adresi: https://izlik.org/JA62PT55WX