FDM Yöntemi Kullanılarak Üretilen Grafen Katkılı PLA+ Malzemeden Üretilen Numunelerin Çeşitli Sürtünme Ve Aşınma Şartları Altında Tribolojik Davranışlarının Incelenmesi

Öz

In the present study, 9 identical samples were produced by using 2% graphene reinforced PLA+ filament by melt deposition modeling (FDM) method. The friction and wear behaviors of the produced graphene-doped samples under different tribological conditions were investigated. In order to create different tribological conditions, the applied load, rotational speed (rpm) and sliding distance were determined as variable parameters throughout the experiments. 3 different levels were selected for each parameter determined as variable. The applied load was determined as 30 – 40 – 50 Newton, rotational speed (rpm) as 200 – 250 – 300, and sliding distance as 100 – 150 – 200 meters. Taguchi L9 array was used in order to reduce the number of experiments in the 3 different parameters and 3 different levels selected. As a result of the experiments performed, it was observed that Sample 1 produced with 30 N load, 200 rpm and 100 meters sliding distance had the highest wear rate and friction coefficient. It was observed that Sample 3, produced with 30 N load – 300 rpm and 200 meters sliding distance, had the lowest wear rate and friction coefficient. In addition, it was observed that the speed parameter was the most effective parameter on the friction coefficient with a delta value of 0.0422, that the parameter levels did not have a linear or consistent increase or decrease effect, and that the speed parameter was the most effective with a Delta value of 0.889 when examined in terms of S / N ratios

Anahtar Kelimeler

• FDM
• tribology
• graphene
• Nanoparticle
• Friction and wear

Investigation of Tribological Behavior of Samples Produced from Graphene Additive PLA+ Material Using FDM Method Under Various Friction and Wear Conditions

Öz

In the present study, 9 identical samples were produced by using 2% graphene reinforced PLA+ filament by melt deposition modeling (FDM) method. The friction and wear behaviors of the produced graphene-doped samples under different tribological conditions were investigated. In order to create different tribological conditions, the applied load, rotational speed (rpm) and sliding distance were determined as variable parameters throughout the experiments. 3 different levels were selected for each parameter determined as variable. The applied load was determined as 30 – 40 – 50 Newton, rotational speed (rpm) as 200 – 250 – 300, and sliding distance as 100 – 150 – 200 meters. Taguchi L9 array was used in order to reduce the number of experiments in the 3 different parameters and 3 different levels selected. As a result of the experiments performed, it was observed that Sample 1 produced with 30 N load, 200 rpm and 100 meters sliding distance had the highest wear rate and friction coefficient. It was observed that Sample 3, produced with 30 N load – 300 rpm and 200 meters sliding distance, had the lowest wear rate and friction coefficient. In addition, it was observed that the speed parameter was the most effective parameter on the friction coefficient with a delta value of 0.0422, that the parameter levels did not have a linear or consistent increase or decrease effect, and that the speed parameter was the most effective with a Delta value of 0.889 when examined in terms of S / N ratios

Anahtar Kelimeler

• FDM
• Tribology
• Graphene
• Nanoparticle
• Friction and Wear

Kaynakça

1. Abir, A. A., & Trindade, B. (2023). A Comparative Study of Different Poly (Lactic Acid) Bio-Composites Produced by Mechanical Alloying and Casting for Tribological Applications. Materials, 16(4), Article 4. https://doi.org/10.3390/ma16041608
2. Ahmed, J., & and Varshney, S. K. (2011). Polylactides—Chemistry, Properties and Green Packaging Technology: A Review. International Journal of Food Properties, 14(1), 37-58. https://doi.org/10.1080/10942910903125284
3. Anderson, I. (2017). Mechanical Properties of Specimens 3D Printed with Virgin and Recycled Polylactic Acid. 3D Printing and Additive Manufacturing, 4(2), 110-115. https://doi.org/10.1089/3dp.2016.0054
4. Aydin, E. (2023). Taguchi Optimizasyon Metodunun İmalat Mühendisliği Alanında Kullanımı: Minitab Örneği. Uludağ University Journal of The Faculty of Engineering, 28(3), 1049-1068. https://doi.org/10.17482/uumfd.1314990
5. Azadi, M., Dadashi, A., Dezianian, S., Kianifar, M., Torkaman, S., & Chiyani, M. (2021). High-cycle bending fatigue properties of additive-manufactured ABS and PLA polymers fabricated by fused deposition modeling 3D-printing. Forces in Mechanics, 3, 100016. https://doi.org/10.1016/j.finmec.2021.100016
6. Carrasco, F., Pagès, P., Gámez-Pérez, J., Santana, O. O., & Maspoch, M. L. (2010). Processing of poly(lactic acid): Characterization of chemical structure, thermal stability and mechanical properties. Polymer Degradation and Stability, 95(2), 116-125. https://doi.org/10.1016/j.polymdegradstab.2009.11.045
7. Chowdhury, M. A., Khalil, M. K., Nuruzzaman, D. M., & Rahaman, M. L. (2011). The Effect of Sliding Speed and Normal Load on Friction and Wear Property of Aluminum. 11(01).
8. Ćwikła, G., Grabowik, C., Kalinowski, K., Paprocka, I., & Ociepka, P. (2017). The influence of printing parameters on selected mechanical properties of FDM/FFF 3D-printed parts. IOP Conference Series: Materials Science and Engineering, 227(1), 012033. https://doi.org/10.1088/1757-899X/227/1/012033

9. Dou, H., Ye, W., Zhang, D., Cheng, Y., & Tian, Y. (2022). Compression Performance with Different Build Orientation of Fused Filament Fabrication Polylactic Acid, Acrylonitrile Butadiene Styrene, and Polyether Ether Ketone. Journal of Materials Engineering and Performance, 31(3), 1925-1933. https://doi.org/10.1007/s11665-021-06363-2
10. El Magri, A., Vanaei, S., Shirinbayan, M., Vaudreuil, S., & Tcharkhtchi, A. (2021). An Investigation to Study the Effect of Process Parameters on the Strength and Fatigue Behavior of 3D-Printed PLA-Graphene. Polymers, 13(19), Article 19. https://doi.org/10.3390/polym13193218
11. Farah, S., Anderson, D. G., & Langer, R. (2016). Physical and mechanical properties of PLA, and their functions in widespread applications—A comprehensive review. Advanced Drug Delivery Reviews, 107, 367-392. https://doi.org/10.1016/j.addr.2016.06.012
12. Fasel, U., Keidel, D., Baumann, L., Cavolina, G., Eichenhofer, M., & Ermanni, P. (2020). Composite additive manufacturing of morphing aerospace structures. Manufacturing Letters, 23, 85-88. https://doi.org/10.1016/j.mfglet.2019.12.004
13. Filameon. (t.y.). Geliş tarihi 15 Ekim 2024, gönderen https://www.filameon.com/
14. Gangadharan, G., Trivedi, S., & Vashi, O. (2024). Taguchi method AWJM optimal solution analysis on Al7050. AIP Conference Proceedings, 3107(1), 110009. https://doi.org/10.1063/5.0213362
15. Gbadeyan, O. J., Mohan, T. P., & Kanny, K. (2021). Tribological Properties of 3D Printed Polymer Composites-Based Friction Materials. Içinde H. Jena, J. K. Katiyar, & A. Patnaik (Ed.), Tribology of Polymer and Polymer Composites for Industry 4.0 (ss. 161-191). Springer. https://doi.org/10.1007/978-981-16-3903-6_9
16. Gonabadi, H., Yadav, A., & Bull, S. J. (2020). The effect of processing parameters on the mechanical characteristics of PLA produced by a 3D FFF printer. The International Journal of Advanced Manufacturing Technology, 111(3), 695-709. https://doi.org/10.1007/s00170-020-06138-4
17. Grémare, A., Guduric, V., Bareille, R., Heroguez, V., Latour, S., L’heureux, N., Fricain, J.-C., Catros, S., & Le Nihouannen, D. (2018). Characterization of printed PLA scaffolds for bone tissue engineering. Journal of Biomedical Materials Research Part A, 106(4), 887-894. https://doi.org/10.1002/jbm.a.36289
18. Hiremath, S. V., Hiremath, C. R., & Tikotkar, R. G. (2020). Optimization of tribological property of carbon fiber reinforced nano filler filled polymer composites using Taguchi method. AIP Conference Proceedings, 2274(1), 030035. https://doi.org/10.1063/5.0023102
19. Huang, B., Aslan, E., Jiang, Z., Daskalakis, E., Jiao, M., Aldalbahi, A., Vyas, C., & Bártolo, P. (2020). Engineered dual-scale poly (ε-caprolactone) scaffolds using 3D printing and rotational electrospinning for bone tissue regeneration. Additive Manufacturing, 36, 101452. https://doi.org/10.1016/j.addma.2020.101452
20. Huang, B., Vyas, C., Byun, J. J., El-Newehy, M., Huang, Z., & Bártolo, P. (2020). Aligned multi-walled carbon nanotubes with nanohydroxyapatite in a 3D printed polycaprolactone scaffold stimulates osteogenic differentiation. Materials Science and Engineering: C, 108, 110374. https://doi.org/10.1016/j.msec.2019.110374
21. Hussain, H. S., Ridzuan, M. J. M., Abdul, M., Rahman, M. T. A., Ismail, M., Khasri, A., & Yudhanto, F. (2024). Effects of nanofillers on the wear and frictional properties of cellulosic fibre-reinforced composites under varying applied loads. FME Transactions, 52(3), 461-470. https://doi.org/10.5937/fme2403461H
22. Khouri, N. G., Bahú, J. O., Blanco-Llamero, C., Severino, P., Concha, V. O. C., & Souto, E. B. (2024). Polylactic acid (PLA): Properties, synthesis, and biomedical applications – A review of the literature. Journal of Molecular Structure, 1309, 138243. https://doi.org/10.1016/j.molstruc.2024.138243
23. Kumar, N., Sharma, A., Manoj, M. K., & Ahn, B. (2024). Taguchi optimized wear and self-lubricating properties of Al-alloy composite reinforced with hybrid B4C–MoS2 particulates. Journal of Materials Research and Technology, 28, 4142-4151. https://doi.org/10.1016/j.jmrt.2024.01.006
24. Laraba, S. R., Rezzoug, A., Avcu, E., Luo, W., Halimi, R., Wei, J., & Li, Y. (2023). Enhancing the tribological performance of PLA-based biocomposites reinforced with graphene oxide. Journal of the Mechanical Behavior of Biomedical Materials, 148, 106224. https://doi.org/10.1016/j.jmbbm.2023.106224
25. Meng, Y., Xu, J., Ma, L., Jin, Z., Prakash, B., Ma, T., & Wang, W. (2022). A review of advances in tribology in 2020–2021. Friction, 10(10), 1443-1595. https://doi.org/10.1007/s40544-022-0685-7
26. Mishra, R. K., & Abdulrahman, S. T. (2018). Tribological Performance of Polymer Composite Materials. İçinde Advanced Polymeric Materials. River Publishers.
27. Nanografi. (t.y.). Geliş tarihi 28 Nisan 2025, gönderen https://nanografi.com/
28. Patrício, T., Domingos, M., Gloria, A., & Bártolo, P. (2013). Characterisation of PCL and PCL/PLA Scaffolds for Tissue Engineering. Procedia CIRP, 5, 110-114. https://doi.org/10.1016/j.procir.2013.01.022
29. Pradhan, S., Kumar Sahu, S., Pramanik, J., & Dhar Badgayan, N. (2022). An insight into mechanical & thermal properties of shape memory polymer reinforced with nanofillers; a critical review. Materials Today: Proceedings, 50, 1107-1112. https://doi.org/10.1016/j.matpr.2021.07.504
30. Rice, S. L., & Moslehy, F. A. (1997). Modeling friction and wear phenomena. Wear, 206(1), 136-146. https://doi.org/10.1016/S0043-1648(96)07360-7
31. Sedničková, M., Pekařová, S., Kucharczyk, P., Bočkaj, J., Janigová, I., Kleinová, A., Jochec-Mošková, D., Omaníková, L., Perďochová, D., Koutný, M., Sedlařík, V., Alexy, P., & Chodák, I. (2018). Changes of physical properties of PLA-based blends during early stage of biodegradation in compost. International Journal of Biological Macromolecules, 113, 434-442. https://doi.org/10.1016/j.ijbiomac.2018.02.078
32. Sundarasetty, H., & Sahu, S. K. (2025). Tribological behavior of PLA reinforced with boron nitride nanoparticles using Taguchi and machine learning approaches. Results in Engineering, 26, 104772. https://doi.org/10.1016/j.rineng.2025.104772
33. Şirin, Ş., Aslan, E., & Akincioğlu, G. (2022). Effects of 3D-printed PLA material with different filling densities on coefficient of friction performance. Rapid Prototyping Journal, 29(1), 157-165. https://doi.org/10.1108/RPJ-03-2022-0081
34. Taguchi, G. (1986). Introduction to quality engineering: Designing quality into products and processes. https://trid.trb.org/View/1179550
35. Unal, H., & Mimaroglu, A. (2003). Influence of test conditions on the tribological properties of polymers. Industrial Lubrication and Tribology, 55(4), 178-183. https://doi.org/10.1108/00368790310480362
36. Vyas, C., Ates, G., Aslan, E., Hart, J., Huang, B., & Bartolo, P. (2020). Three-Dimensional Printing and Electrospinning Dual-Scale Polycaprolactone Scaffolds with Low-Density and Oriented Fibers to Promote Cell Alignment. 3D Printing and Additive Manufacturing, 7(3), 105-113. https://doi.org/10.1089/3dp.2019.0091
37. Zhang, Y., Liang, F., Lin, Y., Chen, X., & Zhu, Y. (2024). Mitigating friction and wear by pre-designed or tribo-induced heterostructures: An overview. Materials Research Letters, 12(8), 535-550. https://doi.org/10.1080/21663831.2024.2356282
38. Zhiani Hervan, S., Altınkaynak, A., & Parlar, Z. (2021). Hardness, friction and wear characteristics of 3D-printed PLA polymer. Proceedings of the Institution of Mechanical Engineers, Part J, 235(8), 1590-1598. https://doi.org/10.1177/1350650120966407