AISI 304L paslanmaz çeliğin EDM sondajında ​​orta ve yüksek deşarj enerjilerinin deneysel değerlendirmesi

Öz

Bu çalışma, 1 mm'lik bir pirinç elektrot kullanılarak AISI 304L paslanmaz çeliğin deşarj enerji seviyelerinin EDM sondajı üzerindeki etkisini araştırmaktadır. Deşarj akımı, nabız-on sürenin (ton) ve nabız kapanma süresinin (MRR), yüzey pürüzlülüğü (SR) ve overcut (OC) üzerindeki etkisini sistematik olarak değerlendirmek için üç replikasyonlu bir Taguchi L9 dik dizi kullanıldı, böylece deneysel hatayı en aza indirdi. Deneyler, sabit dielektrik basınç ve kapasitans altında bir JS AD-20 EDM sondaj makinesi üzerinde gerçekleştirildi. Sonuçlar, deşarj akımı ve nabız-on süresinin MRR ve SR'yi etkileyen en önemli parametreler olduğunu gösterirken, darbe süresi ağırlıklı olarak daha derin delik bölümlerinde aşırı etkilenir. Maksimum MRR (0.116 g/dk) için optimum koşul, 12 A, ton 44 μs ve Toff 10 μs'lik bir akımda elde edildi. Varyans analizi (ANOVA), mevcut ve tonun MRR ve SR'deki varyansın% 75'inden fazlasını oluşturduğunu doğruladı. Bu bulgular, paslanmaz çeliklerde EDM sondaj performansını optimize etmek, üretkenliği, yüzey kalitesini ve boyutsal doğruluğu dengelemek için pratik yönergeler sunmaktadır.

Anahtar Kelimeler

• Elektrikli Deşarj Sondaj (EDD)
• Taguchi Tasarımı; ANOVA
• optik profilometri ile yüzey kalitesi

Experimental Evaluation of Medium and High Discharge Energies in EDM Drilling of AISI 304L Stainless Steel

Abstract

This study investigates the impact of discharge energy levels on EDM drilling of AISI 304L stainless steel using a 1 mm copper electrode. A Taguchi L9 orthogonal array with three replications was employed to systematically evaluate the influence of discharge current, pulse-on time (Ton), and pulse-off time (Toff) on material removal rate (MRR), surface roughness (SR), and overcut (OC), thereby minimizing experimental error. Experiments were conducted on a JS AD-20 EDM drilling machine under constant dielectric pressure and capacitance. The results indicate that discharge current and pulse-on time are the most significant parameters affecting MRR and SR, whereas pulse-off time predominantly influences overcut in deeper hole sections. The optimum condition for maximum MRR (14.34 mm3/min) was achieved at a current of 12 A, Tom of 44 μs, and Toff of 18μs. Analysis of variance (ANOVA) confirmed that current and Ton account for more than 75% of the variance in MRR and SR. These findings provide practical guidelines for optimizing EDM drilling performance in stainless steels, balancing productivity, surface quality, and dimensional accuracy.

Keywords

• Electric Discharge Drilling (EDD)
• Taguchi design; ANOVA
• Surface Quality via Optical Profilometry

Kaynakça

1. Ahmed B., Parametric Analysis of Surface Roughness and Metal Removal Rate during Electrical Discharge Machining of O1 Tool Steel, Journal of Engineering, 2023.
2. Ali S., Influence of Electrodes and Parameters on Micro-EDM Drilling Performances of 304L Stainless Steel, 2nd International Conference on Engineering Technology and its Applications (IICETA), 55–60, 2019.
3. Arslan M.H., Yazman Ş., Hamad A.A., Aksoylu C., Özkılıç Y.O., Gemi L., Shear Strengthening of Reinforced Concrete T-Beams with Anchored and Non-Anchored CFRP Fabrics, Structures, 39, 527–542, 2022.
4. Baysal Ş., Çakir F.H., Ceritbinmez F., Kanca E., Investigation of Fast Hole Drilling EDM Enhancement of Brass EDM Electrodes with Cryogenic Treatment while Machining the Cold Work Steel DIN 1.2379, Canadian Metallurgical Quarterly, 1–12, 2025.
5. Bozdana A.T., Al-Kharkhi N.K., Comparative Experimental and Numerical Investigation on Electrical Discharge Drilling of AISI 304 Using Circular and Elliptical Electrodes, Journal of Mechanical Engineering, 64(4), 269–279, 2018.
6. Bozdana A.T., Ulutaş T., The Effectiveness of Multichannel Electrodes on Drilling Blind Holes on Inconel 718 by EDM Process, Materials and Manufacturing Processes, 31(4), 504–513, 2016.
7. Bozdana A., Al-Karkhi N., Comparative Experimental Investigation and Gap Flow Simulation in Electrical Discharge Drilling Using New Electrode Geometry, Mechanical Sciences, 8, 289–298, 2017.
8. Ceritbinmez F., EDM HızlıDelik Delme Parametrelerinin Kerf veİşlemSüresineEtkileri, Karadeniz Fen Bilimleri Dergisi, 12(2), 663–675, 2022.

9. Ceritbinmez F., Kanca E., An Experimental Investigation on Micro Drilling of Cold Work Steel X153CrMoV12 by EDM, 2021.
10. Ceritbinmez F., Günen A., Gürol U., Çam G., DövmeveEklemeliİmalatYöntemiyleÜretilmiş Inconel 625 AlaşımlarınTermalYöntemleHızlıDelinmesindeElektrotAşınmasının İncelenmesi, International Journal of Advances in Engineering and Pure Sciences, 35(1), 89–99, 2023.
11. D’Urso G., Giardini C., Ravasio C., Effects of Electrode and Workpiece Materials on the Sustainability of Micro-EDM Drilling Process, International Journal of Precision Engineering and Manufacturing, 19(11), 1727–1734, 2018.
12. Erdem O., Çoğun C., Uslan İ., Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD), International Journal of Advances in Engineering and Pure Sciences, Special Issue-1, e11–e16, 2019.
13. Eyercioglu O., Cakir M.V., Gov K., Influence of Machining Parameters on the Surface Integrity in Small-Hole Electrical Discharge Machining, Journal of Engineering Manufacture, 228(1), 51–61, 2014.
14. Fırat A.G., Bozdana A.T., Experimental Study on Effect of Geometry and Material of Tubular Electrode in Electrical Discharge Drilling of Tungsten Carbide, Physica Scripta, 2025.
15. Han Q., Wan H., Han D., EDM-Drilling Characteristics with the Rotation Motion of SS304, IOP Conference Series: Materials Science and Engineering, 538(1), 012011, 2019.
16. Hanash E.A.H., Ali M.Y., Experimental Study of Electrical Discharge Drilling of Stainless Steel UNS S30400, IOP Conference Series: Materials Science and Engineering, 290(1), 012067, 2018.
17. Jahan M.P., Wong Y.S., Rahman M., A Comparative Experimental Investigation of Deep-Hole Micro-EDM Drilling Capability for Cemented Carbide (WC-Co) against Austenitic Stainless Steel (SUS 304), International Journal of Advanced Manufacturing Technology, 46(9–12), 1145–1160, 2010.
18. Jain A., Pandey A.K., Multiple Quality Optimizations in Electrical Discharge Drilling of Mild Steel Sheet, Materials Today: Proceedings, 4, 7252–7261, 2017.
19. Kuppan P., Narayanan S., Rajadurai A., Adithan M., Effect of EDM Parameters on Hole Quality Characteristics in Deep Hole Drilling of Inconel 718 Superalloy, International Journal of Manufacturing Research, 10(1), 45–63, 2015.
20. Naeim N., Aboueleaz M., Elkaseer A., Experimental Investigation of Surface Roughness and Material Removal Rate in Wire EDM of Stainless Steel 304, Materials, 16, 2023.
21. Pal S., Verma A.S., Dixit A., Parametric Optimization of Electric Discharge Drill Machine Using Taguchi and ANOVA Approach, International Research Journal of Engineering and Technology, 5(4), 2737–2741, 2018.
22. Parmar K.V., Patel R.I., Experimental Investigation of Process Parameters of Micro EDM Drilling on Carbide (K20) Material, International Journal of Advance Engineering and Research Development, 1(5), 2014.
23. Riyanto M., Andoko A., Suryanto H., Effect of Current and Pulse-on Time on Material Removal Rate and Surface Roughness of Tungsten Carbide in Electric Discharge Machine Die-Sinking, Journal of Mechanical Engineering Science and Technology (JMEST), 2023.
24. Skrabalak G., Influence of Electrode Tool Length on the Micro EDM Drilling Performance, Procedia CIRP, 68, 594–598, 2018.
25. Suresh T., Suresh P., Optimization of Electrical Discharge Machining Parameters through Drilling of AISI 304 Steel Using Taguchi Technique, AIP Conference Proceedings, 2460(1), 020006, 2022.
26. Tak H.S., Ha C.S., Kim D.H., Lee H.J., Lee H.J., Kang M.C., Comparative Study on Discharge Conditions in Micro-Hole Electrical Discharge Machining of Tungsten Carbide (WC-Co) Material, Transactions of Nonferrous Metals Society of China, 19, s114–s118, 2009.
27. Tanjilul M., Ahmed A., Kumar A., Rahman M., A Study on EDM Debris Particle Size and Flushing Mechanism for Efficient Debris Removal in EDM-Drilling of Inconel 718, Journal of Materials Processing Technology, 255, 263–274, 2018.
28. Trajer M., Analysis of the Relationship between the Properties of Selected Materials and the Parameters of the EDD Process, Materials Research Proceedings, 2023.
29. Youssef H., El-Hofy H., Non-Traditional and Advanced Machining Technologies: Machine Tools and Operations (2nd Ed.), CRC Press, Boca Raton, USA, 2020.
30. Zhang P., Yin Z., Yu M., Tao D., Yu D., Zhang Q., Li H., Investigating Mechanisms of Debris Removal in Ultrasonic Vibration-Assisted EDM Drilling, International Journal of Mechanical Sciences, 2024.