WEDM-Cut NiCrMo: A Comparison of Copper and Brass Wires

Öz

WEDM (Wire Electrical Discharge Machining) is an advanced manufacturing method based on the principle of chip removal by creating high-frequency electrical sparks between the workpiece and the wire electrode. In this method, the wire electrode does not come into contact with the workpiece; instead, electrical discharge occurs through a very small gap. This method offers contactless processing, high precision and smoothness, control of thermal effects, complex geometry cuts, and the ability to process hard materials with tight tolerances, making it possible to easily process materials such as super alloys, carbides, titanium, Inconel, and NiCrMo. In this study, the cutting of NiCrMo alloy, which is difficult to process due to its high strength and low thermal conductivity, using copper and brass wire electrodes in the WEDM method was investigated. SEM (Scanning Electron Microscope) and EDX (Energy Dispersive X-Ray) analyses of the cut surfaces revealed the formation of micro cracks, voids, globules, craters, and debris on the processed surfaces, as well as electrode residues such as Cu and Zn. It was observed that the average surface roughness values of the surfaces cut using copper and brass wire electrodes were 2.331 µm and 3.919 µm Ra, respectively. It has been determined that copper wire is 40.52% more efficient than brass wire electrodes due to its high conductivity, good thermal diffusion and more stable discharges.

Anahtar Kelimeler

• WEDM
• NiCrMo
• Copper
• Brass
• Surface Roughness

WEDM ile Kesilmiş NiCrMo: Bakır ve Pirinç Tellerin Karşılaştırılması

Öz

WEDM (Tel Elektrik Deşarj İşleme) işlenecek parça ile tel elektrot arasında yüksek frekanslı elektriksel kıvılcımlar oluşturularak talaş kaldırma prensibine dayanan ileri imalat yöntemidir. Bu yöntemde tel elektrot iş parçasına temas etmez sadece çok küçük bir boşluk üzerinden elektriksel boşalma gerçekleşir. Bu yöntemin sahip olduğu temassız işleme, yüksek hassasiyet ve pürüzsüzlük, ısıl etkilerin kontrolü, karmaşık geometri kesimleri, dar toleranslarda ve sert malzemeleri işleyebilme özelliklerinden dolayı süper alaşımlar, karbürler, titanyum, inconel, NiCrMo gibi malzemelerin kolayca işlenebilmesine olanak sağlamaktadır. Bu çalışmada yüksek mukavemet ve düşük ısıl iletkenlik nedeniyle zor işlenebilir sınıfında olan NiCrMo alaşımının WEDM yönteminde bakır ve pirinç tel elektrot ile kesilmesi araştırılmıştır. Kesilen yüzeylerin (SEM) Taramali Elektron Mikroskobu ve (EDX) Enerji Dağılımlı X-ışını Spektroskopisi analizleri neticesinde işlenmiş yüzeylerde mikro çatlaklar, oyuklar, kabarcıklar, kraterler ve döküntü oluşumunun yanı sıra Cu ve Zn gibi elektrot kalıntıları tespit edilmiştir. Bakır ve pirinç tel elektrot kullanılarak kesilen yüzeylerin sırası ile ortalama 2,331 µm ve 3,919 µm Ra yüzey pürüzlülük değerlerinde olduğu görülmüştür. Bakır tel’in yüksek iletkenlik, iyi ısıl yayılımı ve daha kararlı deşarjları sayesinde pirinç tel elektrota göre % 40,52 daha performanslı olduğu tespit edilmiştir.

Anahtar Kelimeler

• WEDM
• NiCrMo
• Bakır
• Pirinç
• Yüzey Pürüzlüğü

Kaynakça

1. Bauer, J., Costa, J. F., Carvalho, C. N., Grande, R. H. M., Loguercio, A. D., & Reis, A. (2012). Characterization of two Ni–Cr dental alloys and the influence of casting mode on mechanical properties. Journal of Prosthodontic Research, 56(4), 264-271.
2. Ceritbinmez, F. (2021). An investigation on cutting of the cold work steel X153CrMoV12 by WEDM. Aircraft Engineering and Aerospace Technology, 93(10), 1674-1680.
3. Ceritbinmez, F., Gümüş, F., B., Kanca, E., & Yapıcı, A., (2025) Analysis of NiCrMo surfaces machined by Edm method. 20th International İstanbul Scientific Research Congress on Life, Engineering, Architecture, and Mathematical Sciences, (pp. 256-263). BZT Turan Publishing House.
4. Ceritbinmez, F., & Günen, A. (2024). Comparison of drilling of Inconel 625 by AWJM and WEDM. Aircraft Engineering and Aerospace Technology, 96(2), 329-336.
5. Ceritbinmez, F., & Kanca, E. (2022). The effects of using brass and copper wires on the cutting quality of Sleipner cold work steel cut by WEDM. Journal of Materials and Mechatronics: A, 3(2), 163-178.
6. Chen, Z., Zhang, Y., Zhang, G., Huang, Y., & Liu, C. (2017). Theoretical and experimental study of magnetic-assisted finish cutting ferromagnetic material in WEDM. International Journal of Machine Tools and Manufacture, 123, 36-47.
7. Das, S., & Joshi, S. N. (2020). Estimation of wire strength based on residual stresses induced during wire electric discharge machining. Journal of Manufacturing Processes, 53, 406-419.
8. Deshmukh, S. S., Zubair, A. S., Jadhav, V. S., & Shrivastava, R. (2019). Optimization of process parameters of wire electric discharge machining on AISI 4140 using taguchi method and grey relational analysis. Materials Today: Proceedings, 18, 4261-4270.

9. Ezugwu, E. O., Wang, Z. M., & Machado, A. R. (1999). The machinability of nickel-based alloys: a review. Journal of Materials Processing Technology, 86(1-3), 1-16.
10. Fan, W., Ji, W., Wang, L., Zheng, L., & Wang, Y. (2020). A review on cutting tool technology in machining of Ni-based superalloys. The International Journal of Advanced Manufacturing Technology, 110(11), 2863-2879.
11. Galo, R., Ribeiro, R. F., Rodrigues, R. C. S., Rocha, L. A., & Mattos, M. D. G. C. D. (2012). Effects of chemical composition on the corrosion of dental alloys. Brazilian dental journal, 23, 141-148.
12. Gokcekaya, O., Günen, A., Ceritbinmez, F., Bahador, A., Nakano, T., & Çetin, M. (2024). Wire-EDM performance and surface integrity of Inconel 718 with unique microstructural features fabricated by laser powder bed fusion. The International Journal of Advanced Manufacturing Technology, 130(9), 4513-4528.
13. Günen, A., Ceritbinmez, F., Patel, K., Akhtar, M. A., Mukherjee, S., Kanca, E., & Karakas, M. S. (2022). WEDM machining of MoNbTaTiZr refractory high entropy alloy. CIRP Journal of Manufacturing Science and Technology, 38, 547-559.
14. Haider, A., Jaffery, S. H. I., Khan, A. N., Qadir, N., & Jing, X. (2023). Effect of cerium on mechanical, metallurgical and biomedical properties of NiCrMoB dental alloy. Journal of Materials Research and Technology, 24, 5082-5093.
15. Haider, A., Jaffery, S. H. I., Khan, A. N., Butt, S. I., & Jing, X. (2024). Processing and characterization of beryllium free Ni–Cr–Mo biomaterial doped with cerium, boron and titanium for dental applications. Journal of Materials Research and Technology, 30, 7495-7509.
16. Huang, H. H. (2003). Surface characterization of passive film on NiCr-based dental casting alloys. Biomaterials, 24(9), 1575-1582.
17. Jahare, M. H., Idris, M. H., & Hassim, M. H. (2022). Effect of WEDM parameters on material removal rate and kerf’s width of cobalt chromium molybdenum using full factorials design. Advances in Materials and Processing Technologies, 8(1), 550-563.
18. Ji, R., Liu, Y., Diao, R., Xu, C., Li, X., Cai, B., & Zhang, Y. (2014). Influence of electrical resistivity and machining parameters on electrical discharge machining performance of engineering ceramics. PloS one, 9(11), e110775.
19. Ji, W., Liu, X. L., Li, H. Y., You, H. Y., & Fan, M. C. (2013). Research of PCBN tool wear mechanism in turning Ni-based superalloy. Advanced Materials Research, 820, 185-189.
20. Kulkarni, V. N., Gaitonde, V. N., Mallaiah, M., Karnik, R. S., & Davim, J. P. (2022). Tool wear rate and surface integrity studies in wire electric discharge machining of NiTiNOL shape memory alloy using diffusion annealed coated electrode materials. Machines, 10(2), 138.
21. Lu, C., Zheng, Y., & Zhong, Q. (2017). Corrosion of dental alloys in artificial saliva with Streptococcus mutans. PLoS One, 12(3), e0174440.
22. Mouralová, K., Benes, L., Prokes, T., Bednar, J., Zahradnicek, R., & Fries, J. (2020). Machining of pure molybdenum using WEDM. Measurement, 163, 108010.
23. Mouralova, K., Benes, L., Zahradnicek, R., Bednar, J., Zadera, A., Fries, J., & Kana, V. (2020). WEDM Used for machining high entropy alloys. Materials, 13(21), 4823.
24. Murugan, V. K., & Mathews, D. P. (2012). Surface hardness behaviour of heat treated Ni-Cr-Mo alloys. International Journal of Engineering Science and Technology, 4(12), 4739-4744.
25. Muller, A. W. J., Maessen, F. J. M. J., & Davidson, C. L. (1990). Determination of the corrosion rates of six dental NiCrMo alloys in an artificial saliva by chemical analysis of the medium using ICP-AES. Dental Materials, 6(1), 63-68.
26. Nishanth, B. S., Kulkarni, V. N., & Gaitonde, V. N. (2019, December). A review on conventional and non-conventional machining of titanium and nickel based alloys. In AIP conference proceedings (Vol. 2200, No. 1, p. 020091). AIP Publishing LLC.
27. Rohilla, V. K., Goyal, R., Kumar, A., Singla, Y. K., & Sharma, N. (2021). Surface integrity analysis of surfaces of nickel-based alloys machined with distilled water and aluminium powder-mixed dielectric fluid after WEDM. The International Journal of Advanced Manufacturing Technology, 116(7), 2467-2472.
28. Saravanan, R., Hamidon, R., Murad, N. M., & Zailani, Z. A. (2021). Machining of cobalt chromium molybdenum (CoCrMo) alloys: A review. Intelligent Manufacturing and Mechatronics: Proceedings of SympoSIMM 2020, 413-424.
29. Sharma, N., Gupta, K., & Davim, J. P. (2019). On wire spark erosion machining induced surface integrity of Ni55. 8Ti shape memory alloys. Archives of Civil and Mechanical Engineering, 19(3), 680-693.
30. Souza, M. A. D., Fiorin, B. D. O., Hashimoto, T. M., Rosifini, A. P., Nunes, C. A., Baptista, C. A. R. P., & Ramos, A. S. (2019). Influence of niobium or molybdenum addition on microstructure and tensile properties of nickel-chromium alloys. Metals, 9(5), 589.
31. Siemers, C., Zahra, B., Ksiezyk, D., Rokicki, P., Spotz, Z., Fusova, L., Rösler, J., & Saksl, K. (2011). Chip formation and machinability of nickel-base superalloys. Advanced Materials Research, 278, 460-465.
32. Singh, N., & Bharti, P. S. (2022). Multi-Objective parametric optimization during micro-EDM drilling of Ti-6Al-4 V using teaching learning Based optimization algorithm. Materials Today: Proceedings, 62, 262-269.