Effect of Number of Draw Frame Passages on Rotor-Spun Yarn Quality

Öz

This study investigates the effects of the number of passages for draw frame machines on the quality of rotor-spun yarn. In the presented study, the goal is to produce more cost-effective yarn with similar physical properties to those obtained with two drawing passages by reducing the number of drawing passages. Additionally, the study aims to achieve a lower carbon footprint and reduce the environmental impacts of production processes through lower energy consumption. Yarn samples of Ne 20/1 and Ne 10/1 with the same cotton fibre were produced by means of both single-passage and double-passage drawing machines. The unevenness and tensile properties of the produced yarns were measured using Uster Tester and Uster Tensorapid testing devices, while abrage control was evaluated in an abrage cabinet under ultraviolet light. Furthermore, the energy consumption of the eliminated drawing machine was measured using an energy analyzer. The yarn samples produced with the single passage drawing machine demonstrated better IPI (imperfections) values than those produced with the two-passage system, and the tensile strength values remained at comparable levels. Under UV light, no abrage differences were observed between the yarns from the two different production processes. Energy and raw material waste savings were achieved by eliminating one of the drawing machines. Additionally, considering a waste ratio of 0.6% for a single passage drafting machine, it is estimated that approximately 100 tons of cotton waste per year can be prevented in a rotor-spun facility producing 50 tons of yarn daily. The study revealed that the reduction in raw material and energy consumption enables the production process to be carried out with a lower carbon footprint, thereby making a significant contribution to sustainability. Furthermore, this approach results in a notable reduction in yarn production costs.

Anahtar Kelimeler

• Draw frame
• Open-end yarn
• Yarn quality
• Abrage

Etik Beyan

Sunulan “Effect of Number of Draw Frame Passages on Rotor-Spun Yarn Quality” başlıklı çalışmada etik kurul izni gerekmemektedir

Kaynakça

1. Başoğul, Y., Göksu, T. T., and Baran, M. F. (2021). Bir tekstil fabrikasının karbon ayak izinin değerlendirilmesi. Avrupa Bilim ve Teknoloji Dergisi, Ejosat 2021 Ek Sayı 1, 146-150.
2. Bevilacqua, M., Ciarapica, F. E., Giacchetta, G., and Marchetti, B. (2011). A carbon footprint analysis in the textile supply chain. International Journal of Sustainable Engineering, 4(1), 24-36.
3. Can, M. (1995). Endüstriyel atık akışkanların değerlendirilmesi ve ülke ekonomisine katkısı. Ekoloji Dergisi, Ekim, Kasım, Aralık, Sayı: 17.
4. Chaudhari, V., and Raichurkar, P. P. (2016). Effect of draw frame bottom roller gauge setting on yarn quality. International Journal on Textile Engineering and Processes, 2(2), 29-30.
5. Doğan, H., and Yılankırkan, N. (2015). Türkiye’ nin enerji verimliliği potansiyeli ve projeksiyonu. Gazi Üniversitesi Fen Bilimleri Dergisi. Part: C, 375-383.
6. Elhawary, I. A. (2015). Fibre to yarn: Staple-yarn spinning. In R. Sinclair (Ed.), Textiles and Fashion (pp. 191-212). Woodhead Publishing.
7. Evrim, İ. E., and Seyhun, Ö. K. (2022). Sınırda karbon düzenleme mekanizmasi ve Türkiye’ nin ihracatına olası etkileri. Ege Stratejik Araştırmalar Dergisi, 13(1), 1-13.
8. Hoffman, A. J. (2011). The culture and discourse of climate skepticism. Strategic Organization, 9(1), 77-84.

9. Ishtiaque, S. M., Mukhopadhyay, A., and Kumar, A. (2009). Impact of high-speed draw frame and its preparatory on packing and related characteristics of ring spun yarn. The Journal of the Textile Institute, 100(8), 657-667.
10. Kmansuri, A., and Pathak, R. (2022). Yield and quality improvement of Asian spinning mill. International Journal of Mechanical Engineering, 7(4), 1-8. ISSN: 0974-5823.
11. Maraşlioğlu, B. (2018). Open-end İplik Tesislerinde Enerji Kalitesinin İncelenmesi. (Master's Thesis) Kahramanmaraş Sütçü İmam Üniversitesi Fen Bilimleri Enstitüsü, Kahramanmaraş, Türkiye.
12. Ozcan, B., and Ozturk, I. (2019). Renewable energy consumption-economic growth nexus in emerging countries: A bootstrap panel causality test. Renewable and Sustainable Energy Reviews, 104, 30-37.
13. Ramasamy, K. M., Duraisamy, R., and Mammo, H. (2019). Improving yarn quality by modification on drafting zone settings of draw frame. International Journal of Engineering Trends and Technology, 67(11), 226-231.
14. Sert, M. Ö., Eyidoğan, M., Kiliç, F. Ç., and Kaya, D. (2017). Bir Entegre Tekstil Üretim İşletmesinde Enerji Verimliği Çalışması, 1st International Conference on Energy Systems Engineering (pp. 246-250).
15. Şekkeli, M. and Keçecioğlu, Ö. F. (2012). Scada Based an Energy Saving Approach to Operation of Stenter Machine in a Textile Plant Using Waste Heat Recovery System. Journal of Textile & Apparel/Tekstil ve Konfeksiyon, 22(3), 248-257.
16. Uçak, F. (2010). Tekstil terbiye işletmelerinde ramöz makinasında enerji tasarrufu. (Master's Thesis) Çukurova Üniversitesi Fen Bilimleri Enstitüsü, Adana, Türkiye.
17. Yılmaz, S. (2010). Tekstil kurutma makinelerinin enerji verimliliğinin artırılması. (Master's Thesis) Uludağ Üniversitesi Fen Bilimleri Enstitüsü, Bursa, Türkiye.