Abstract

MECHANICAL PROPERTIES OF AA5754 SHEETS WELDED BY COLD METAL TRANSFER METHOD

Öz

Cold Metal Transfer (CMT) is a modified gas metal arc welding method. This method is different from conventional gas metal arc welding methods. In this process the heat input and the formation of spatter are reduced with the control of the wire movement and arc. So, CMT welding became indispensable in the welding of thin sheets. The importance of lightweight structures in vehicles is increasing day by day, so the use of thin sheet aluminum alloys such as AA5754 is becoming increasingly widespread. In present study, 2mm thick AA5754 sheets were joined with cold metal transfer welding using ER5356 (AlMg5) filler wire. The effect of heat input on the weld quality was investigated. Microstructural examinations were executed by optical microscope and SEM. Mechanical properties of joints were determined by tensile and bending tests. It was found that increasing heat input did not have a significant effect on tensile strength of AA5754-AA5754 joints, while it corrupted the bending strength.   

Anahtar Kelimeler

• AA5754,ER5356,Cold Metal Transfer Welding,SEM,Welding

Kaynakça

1. 1. Kodama, S., Ishida, Y., Furusako, S., Saito, M., Miyazaki, Y., and Nose, T., (2013). Arc Welding Technology for Automotive Steel Sheets, Nippon Steel Technical Report. Volume 103, pp:83-90.
2. 2. Larsson, J.K., Lundgren, J., Asbjörnsson, E., and Andersson, H., (2009). Extensive introduction of ultra high strength steels sets new standards for welding in the body shop, Welding in the World, Volume 53, Issue 5, pp:4–14.
3. 3. Sakiyama, T., Murayama, G., Naito, Y., Saita, K., Miyazaki, Y., Oikawa, H., and Nose, T., (2013). Dissimilar Metal Joining Technologies for Steel Sheet and Aluminum Alloy Sheet in Auto Body, Nippon Steel Technical Report, Volume 103, pp:91-98.
4. 4. Davis, J.R., (1999). Corrosion of Aluminum and Aluminum Alloys. ASM International.
5. 5. Casalino, G., Campanelli, S., and Ludovico, A.D., (2012). Hybrid Welding Of AA5754-H111 Alloy Using A Fiber Laser, Advanced Materials Research, Volume 628, pp:193-198.
6. 6. Messler, R.W., Bell, J., and Craigue, O., (2003). Laser Beam Weld Bonding of AA5754 for Automobile Structures, Welding Journal, pp:151-159.
7. 7. Leo, P., Renna, G., Casalino, G., and Olabi, A.G., (2015). Effect of power distribution on the weld quality during hybrid laser welding of an Al–Mg alloy, Optics & Laser Technology, Volume 73, pp:118–126.
8. 8. Punkari, A., Weckman, D.C., and Kerr, H.W., (2003). Effects of magnesium content on dual beam Nd:YAG laser welding of Al–Mg alloys, Science and Technology of Welding and Joining, Volume 8, Issue 4, pp:269-281.

9. 9. Davies, G., (2003). Materials for Automobile Bodies. Butterworth-Heinemann, Oxford.
10. 10. Frostevarg, J., Kaplan, A.F.H., and Lamas, J., (2014). Comparison of CMT with other arc modes for laser-arc hybrid welding of steel, Welding in the World, Volume 58, Issue 5, pp:649–660.
11. 11. Dutra, J.C., Silva, R.H.G., Savi, B.M., Marques, C., and Alarcon, O.E., (2015). Metallurgical characterization of the 5083H116 aluminum alloy welded with the cold metal transfer process and two different wire-electrodes (5183 and 5087), Welding in the World, Volume 59, Issue 6, pp:797–807.
12. 12. Yu, Y., Wang, C., Hu, X., Wang J., and Yu, S., (2010). Porosity in fiber laser formation of 5A06 aluminum alloy, Journal of Mechanical Science and Technology, Volume 24, Issue 5, pp:1077-1082.
13. 13. Casalino, G., Mortello, M., Leo, P., Benyounis, K.Y., and Olabi, A. G., (2014). Study on arc and laser powers in the hybrid welding of AA5754 Al-alloy, Materials & Design, Volume 61, 2014, pp:191–198.
14. 14. Halim, H., Wilkinson, D.S., and Niewczas, M., (2007). The Portevin–Le Chatelier (PLC) effect and shear band formation in an AA5754 alloy, Acta Materialia, Volume 55, pp:4151–4160.
15. 15. Mindivan, F., Kaya, H., Özer, M., Uçar, M., and Samur, R., (2015). Investigation of Corrosion Behavior of the AA5754 Aluminum Alloy Joined Using Friction Stir Welding Method, Celal Bayar University Journal of Science, Volume 11, Issue 3, pp:413-422.
16. 16. Leo, P., D'Ostuni, S., and Casalino, G., (2016). Hybrid Welding of AA5754 Annealed Alloy: Role of Post Weld Heat Treatment on Microstructure and Mechanical Properties, Materials & Design, Volume 90, pp:777-786.
17. 17. Lloyd, D.J., Evans, D., Pelow, C., Nolan, P., and Jain, M., (2002). Bending in aluminium alloys AA 6111 and AA 5754 using the cantilever bend test, Materials science and technology, Volume 18, Issue 6, pp:621-628.
18. 18. Sarkar, J., Kutty, T.R.G., Conlon, K.T., Wilkinson, D.S., Embury, J.D., and Lloyd, D.J., (2001). Tensile and bending properties of AA5754 aluminum alloys, Materials Science and Engineering: A, Volume 316, Issue 1–2, pp:52–59.