Öz
Drawbeads are used as control mechanism regulated the flow rate at certain locations of the sheet to minimize or prevent defects such as tearing, wrinkling and springback that occur on sheet during a sheet metal forming process. In this study, drawbead restraining force was measured for the sheet metal through blankholder and lower die with a round drawbead with various penetration. This experimental data were used and the mathematical model calculated drawbead restraining force as a function of bead penetration was developed. Comparison of the results of mathematical model with the corresponding experimental results and PAM-STAMP model was showed in excellent agreement.
Anahtar Kelimeler
Kaynakça
- (REFERENCES) Tiryaki, A.E., Kozan, R., Çift Fazlı Çelik Sacda Kare Süzdürme Çubuğunun Oluşturduğu Frenleme Kuvvetinin Kestirimi, Mühendis ve Makina, Cilt 51, Sayı 609, 2010.
- Hsu, C.W., Ulsoy, A.G., Demeri M.Y., Development of Process Control in Sheet Metal Forming, Journal of Materials Processing Technology, 127, pp. 361-368, 2002.
- Çiçek, O., Effect of Drawbeads in Sheet Metal Forming, MSc Thesis, Istanbul Technical University, Department of Mechanical Engineering, August, 2005.
- Tiryaki, A.E, Sac Metallerin Şekillendirilmesinde Kullanılan Süzdürme Çubuğunun Modellenmesi ve Kontrolü, Doktora Tezi, Sakarya Üniversitesi, Makina Mühendisliği Bölümü, 2010. http://www.hellotrade.com/interlakentechnology-corporation-usa/product3.html Demeri, M.Y., Drawbeads in Sheet Metal Forming, Journal of Materials Engineering and Performance, 2/6, pp. 863-866, 1993. http://www.globalspec.com/reference/70325/2 03279/ chapter-16-stamping
- PAM-STAMP user manual
Öz
Drawbeads are used as control mechanism regulated the flow rate at certain locations of the sheet to minimize or prevent defects such as tearing, wrinkling and springback that occur on sheet during a sheet metal forming process. In this study, drawbead restraining force was measured for the sheet metal through blankholder and lower die with a round drawbead with various penetration. This experimental data were used and the mathematical model calculated drawbead restraining force as a function of bead penetration was developed. Comparison of the results of mathematical model with the corresponding experimental results and PAM-STAMP model was showed in excellent agreement.
Anahtar Kelimeler
Kaynakça
- (REFERENCES) Tiryaki, A.E., Kozan, R., Çift Fazlı Çelik Sacda Kare Süzdürme Çubuğunun Oluşturduğu Frenleme Kuvvetinin Kestirimi, Mühendis ve Makina, Cilt 51, Sayı 609, 2010.
- Hsu, C.W., Ulsoy, A.G., Demeri M.Y., Development of Process Control in Sheet Metal Forming, Journal of Materials Processing Technology, 127, pp. 361-368, 2002.
- Çiçek, O., Effect of Drawbeads in Sheet Metal Forming, MSc Thesis, Istanbul Technical University, Department of Mechanical Engineering, August, 2005.
- Tiryaki, A.E, Sac Metallerin Şekillendirilmesinde Kullanılan Süzdürme Çubuğunun Modellenmesi ve Kontrolü, Doktora Tezi, Sakarya Üniversitesi, Makina Mühendisliği Bölümü, 2010. http://www.hellotrade.com/interlakentechnology-corporation-usa/product3.html Demeri, M.Y., Drawbeads in Sheet Metal Forming, Journal of Materials Engineering and Performance, 2/6, pp. 863-866, 1993. http://www.globalspec.com/reference/70325/2 03279/ chapter-16-stamping
- PAM-STAMP user manual
Ayrıntılar
| Birincil Dil | Türkçe |
|---|---|
| Konular | Mühendislik |
| Bölüm | Araştırma Makalesi |
| Yazarlar | |
| Yayımlanma Tarihi | 1 Haziran 2013 |
| Gönderilme Tarihi | 23 Ağustos 2012 |
| Kabul Tarihi | 13 Aralık 2012 |
| Yayımlandığı Sayı | Yıl 2013 Cilt: 17 Sayı: 2 |
Kaynak Göster
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.