GÜÇ SİSTEMLERİ GEÇİCİ REJİM SİMÜLASYONLARINDA ZAMAN ADIM UZUNLUĞU ETKİSİNİN İNCELENMESİ

Öz

Güç sistemlerinde yıldırım düşmesi gibi yüksek frekanslı geçici rejim olaylarının simülasyonu, ekipman güvenliği ve koruma sistemi tasarımı için hayati önem taşımaktadır. Bu çalışmada, geçici rejim analizlerinin doğruluğunu belirleyen en kritik parametrelerden biri olan zaman adım uzunluğunun (Δt) sonuçlar üzerindeki etkisi kapsamlı bir şekilde analiz edilmiştir. Çalışma kapsamında, 300 km uzunluğunda dağınık parametreli bir iletim hattı, Heidler modeli ile temsil edilen bir yıldırım darbesi ve 10 diskten oluşan merdiven ağı tipi bir güç transformatörü modeli kullanılarak karmaşık bir test sistemi oluşturulmuştur. Analiz sürecinde, analitik bir yaklaşım olan durum-uzayı yöntemi ile endüstriyel standart ATP-EMTP yazılımı üzerinden alınan sonuçlar karşılaştırılmıştır. Simülasyonlar, 5x10−8 s ile 5x10−4 s arasında değişen farklı zaman adımları için tekrarlanmıştır. Elde edilen bulgular, zaman adım uzunluğu arttıkça akım ve gerilim dalga formlarının karakteristik yapısının bozulduğunu ve tepe değerlerinde büyük sapmalar meydana geldiğini göstermiştir. Özellikle büyük zaman adımlarında, kA mertebesindeki akım değerlerinin 1 A'in altına düştüğü ve sonuçların fiziksel gerçekliğini tamamen yitirerek sayısal kararsızlığa yol açtığı tespit edilmiştir. Çalışma, yüksek frekanslı bileşenleri içeren geçici olayların doğru modellenmesi için zaman adımının sadece Nyquist-Shannon kriterini sağlamakla kalmayıp, sistemin dinamik yanıtlarını yakalayacak kadar hassas seçilmesinin mühendislik hesaplamaları açısından zorunlu olduğunu kanıtlamaktadır.

Anahtar Kelimeler

• Geçici rejim analizi
• Zaman adım uzunluğu
• Durum-uzayı yöntemi
• ATP-EMTP
• Dağınık parametreli hatlar.

AN ANALYSIS OF THE EFFECT OF TIME STEP LENGTH IN TRANSIENT SIMULATIONS OF POWER SYSTEMS

Öz

Bearing Simulation of high-frequency transient events, such as lightning strikes in power systems, is vital for equipment safety and protection system design . In this study, the impact of time step length (Δt), which is one of the most critical parameters determining the accuracy of transient analysis, has been comprehensively analyzed . Within the scope of the study, a complex test system was created using a 300 km distributed parameter transmission line, a lightning stroke represented by the Heidler model, and a ladder network type power transformer model consisting of 10 disks. In the analysis process, results obtained from the analytical state-space method and the industry-standard ATP-EMTP software were compared. Simulations were conducted for different time steps ranging from 5x10⁻⁸ s to 5x10⁻⁴ s. The findings demonstrated that as the time step length increases, the characteristic structure of current and voltage waveforms deteriorates, and significant deviations occur in peak values. Especially at large time steps, current values in the kA range dropped below 1 A, losing physical reality and leading to numerical instability. The study proves that for the accurate modeling of transient events containing high-frequency components, choosing a time step that is precise enough to capture the system's dynamic responses rather than merely satisfying the Nyquist-Shannon criterion is essential for reliable engineering calculations

Anahtar Kelimeler

• Transient analysis
• Time step length
• State-space method
• ATP-EMTP
• Distributed parameter lines.

Kaynakça

1. Abourida, S., Bélanger, J., & Jalili-Marandi, V. (2016). Real-time power system simulation: EMT vs. phasor. OPAL-RT Technologies.
2. Adamczyk, B., Pajak, P., & Florkowski, M. (2024). Comparison of initial voltage distributions in layer and disc type power transformer windings. IEEE Transactions on Dielectrics and Electrical Insulation, 32(1), 73–82. https://doi.org/10.1109/TDEI.2024.3473893 Bergeron, L. (1961). Water hammer in hydraulics and wave surges in electricity.
3. Bilal, G., Gomez, P., Salcedo, R., & Villanueva-Ramirez, J. M. (2019). Electromagnetic transient studies of large distribution systems using frequency domain modeling methods and network reduction techniques. International Journal of Electrical Power and Energy Systems, 110, 11–20. https://doi.org/10.1016/j.ijepes.2019.02.043
4. Branin, F. H. (1967). Transient analysis of lossless transmission lines. Proceedings of the IEEE, 55(11), 2012–2013. https://doi.org/10.1109/PROC.1967.6033
5. Chaban, A., Popenda, A., & Szafraniec, A. (2023). Including shield wires in the analysis of transient processes. Energies, 16, 1–20. https://doi.org/10.3390/en16237870
6. Colqui, J. S. L., De Araújo, A. R. J., & Kurokawa, S. (2019). Improving the performance of a lumped transmission line model used in electromagnetic transient analysis. IET Generation, Transmission and Distribution, 13(21), 4942–4951. https://doi.org/10.1049/iet-gtd.2018.6301
7. Dommel, H. (1969). Digital computer solution of electromagnetic transients in single-and multiphase networks. IEEE Transactions on Power Apparatus and Systems, PAS-88(4), 388–399. https://doi.org/10.1109/TPAS.1969.292459
8. Dommel, H. (1992). EMTP theory book (2nd ed.). Microtran Power System Analysis Corporation.

9. Ghiasi, S. M. S., Abedi, M., & Hosseinian, S. H. (2022). A new approach for the estimation of transient voltage profile along transmission line. Canadian Journal of Electrical and Computer Engineering, 40(4), 295–302. https://doi.org/10.1109/cjece.2017.2763988
10. Ghorbal, M. B., Mirzaei, H. R., & Rahimpour, E. (2024). Precise modeling of chopped lightning impulse test of power transformers. Electric Power Systems Research, 230. https://doi.org/10.1016/j.epsr.2024.110207
11. Heidler, F., & Cvetić, J. (2002). A class of analytical functions to study the lightning effects associated with the current front. European Transactions on Electrical Power, 12(2), 141–150. https://doi.org/10.1002/etep.4450120209
12. Heidler, F., Cvetić, J. M., & Stanić, B. V. (1999). Calculation of lightning current parameters. IEEE Transactions on Power Delivery, 14(2), 399–404. https://doi.org/10.1109/61.754080
13. Jaimis Colqui, S. L., Anderson De Araujo, R. J., & Kurokawa, S. (2018). A new methodology for calculating electromagnetic transients in transmission lines. In INDUSCON 2018- Proceedings. 13th IEEE International Conference on Industry Applications (pp. 949–954). https://doi.org/10.1109/INDUSCON.2018.8627286
14. Jurišić, B., Jurković, Z., Župan, T., & Marković, M. (2024). Hybrid analytical-FEM approach for power transformer transient analysis. Journal of Energy - Energija, 73(1), 8–13. https://doi.org/10.37798/2024731512
15. Kurokawa, S., Yamanaka, F. N. R., Prado, A. J., & Pissolato, J. (2009). Inclusion of the frequency effect in the lumped parameters transmission line model: State space formulation. Electric Power Systems Research, 79(7), 1155–1163. https://doi.org/10.1016/j.epsr.2009.02.007
16. Ma, X., Zhang, N., Zhou, X., He, Z., Wang, Y., & Wang, S. (2024). Calculation of lightning impulse voltage distribution of voltage transformer. In Proceedings of 2024 IEEE 7th International Electrical and Energy Conference, CIEEC 2024 (pp. 1256–1261). https://doi.org/10.1109/CIEEC60922.2024.10583604
17. Mamiş, M. S., Kaygusuz, A., & Köksal, M. (2010). State variable distributed-parameter representation of transmission line for transient simulations. Turkish Journal of Electrical Engineering and Computer Sciences, 18(1), 31–42. https://doi.org/10.3906/elk-0905-2
18. Samal, M., & Mondal, M. (2022). Estimation of a disk transformer winding’s ladder network parameters using analytical, FEM, and terminal measurements. In 2022 IEEE North Karnataka Subsection Flagship International Conference, NKCon 2022 (pp. 1–6). https://doi.org/10.1109/NKCon56289.2022.10126684
19. Samal, M., & Mondal, M. (2023). Power transformer FRA studies using ladder, multi-conductor transmission lines (MTL), circular MTL, and hybrid winding models. In 2023 IEEE 8th International Conference for Convergence in Technology, I2CT 2023 (pp. 1–6). https://doi.org/10.1109/I2CT57861.2023.10126461
20. Vahabzadeh, T., Ebrahimi, S., & Jatskevich, J. (2025). Discretized impedance-based modeling of converter-interfaced energy resources for state-variable-based real-time EMT simulators. IEEE Open Journal of Power Electronics, 6, 212–227.