P20 Çeliğinin CBN Kesicilerle Frezelenmesi Sırasında Asınma ve Yüzey Pürüzlülüğüne İlerleme Değerinin Etkisi
Abstract
55 HRC’ye sertlestirilmis P20 kalıp çeliği iki farklı tip CBN kesici takımla, yüksek hızlarda islenmistir. Deneylerde kullanılan CBN kesici takımların birincisi düsük CBN katkılı (CBN-DS) ve seramik bağlayıcılıdır. Diğeri ise yüksek CBN katkılı (CBN-YM) ve metal bağlayıcılıdır. Elde edilen takım asınması ve yüzey pürüzlülüğü değerleri CBN kesici takımlar için karsılastırılıp, ilerleme, CBN oranı ve bağlayıcının takım asınması ve yüzey pürüzlülüğü üzerine etkisi arastırılmıstır.
References
- [1] Bossom, P.K., (1990), “Finish Machining of Hard Ferrous Workpieces”, Ind. Diam. Rev., Vol. May 1990, pp 228-232. [2] Chou, Y.K., Evans, C.J., Barash, M.M., (2003), “Experimental Investigation on Cubic Boron Nitride Turning of Hardened AISI 52100 Steel”, J. Mater. Process. Technol., Vol. 134, pp 1-9. [3] Fallböhmer, P., Rodriguez, C.A., Özel, T., Altan, T., (2000), “Highspeed machining of cast iron and alloy steels for die and mold manufacturing”, J. Mater. Process. Technol., Vol. 98, pp 104-115. [4] Hooper, R.M., Shakib II., J., Brookes, C.A., (1988), “Microstructure and Wear of TiC-Cubic BN Tools”, Mater. Sci. Eng., Vol. 105/106, pp 429- 433. [5] Klimenko, S.A., Mukovoz, Y.A., Lyashko, V.A., Vashchenco, A.N., Ogorodnik, V.V., (1992), “On the Wear Mechanism of Cubic Boron Nitride Base Cutting Tools”, Wear, Vol. 157, pp 1-7. [6] Narutaki, N., Yamane, Y., (1979), “Tool Wear and Cutting Temperature of CBN Tools in Machining of Hardened Steels”, Ann. CIRP, Vol. 28, pp 23-28. [7] Takastu, S., Shimoda, H., Otani, K., (1983), “Effect of CBN Content on the Cutting Performance of Polycrystalline CBN Tools”, Int. J. Refr. Hard Met., Vol. 12, pp. 175-178. [8] Tlusty, G., (2000), Manufacturing Processes and Equipment, Prentice- Hall, Inc., Upper Saddle River, New Jersey.
P20 Çeliğinin CBN Kesicilerle Frezelenmesi Sırasında Asınma ve Yüzey Pürüzlülüğüne İlerleme Değerinin Etkisi
Abstract
P20 mold steel hardened to 55 HRC was machined by using two different types of cubic boron nitride cutting tools at high cutting speeds. One of the CBN tools used in the experiments is a low CBN content tool with a ceramic binder. The other one is a high CBN content tool with a metal binder. Tool wear and surface roughness results obtained with each type of tools were compared, and the effects of feed rate, CBN content and binder on tool wear and surface roughness were investigated.
References
- [1] Bossom, P.K., (1990), “Finish Machining of Hard Ferrous Workpieces”, Ind. Diam. Rev., Vol. May 1990, pp 228-232. [2] Chou, Y.K., Evans, C.J., Barash, M.M., (2003), “Experimental Investigation on Cubic Boron Nitride Turning of Hardened AISI 52100 Steel”, J. Mater. Process. Technol., Vol. 134, pp 1-9. [3] Fallböhmer, P., Rodriguez, C.A., Özel, T., Altan, T., (2000), “Highspeed machining of cast iron and alloy steels for die and mold manufacturing”, J. Mater. Process. Technol., Vol. 98, pp 104-115. [4] Hooper, R.M., Shakib II., J., Brookes, C.A., (1988), “Microstructure and Wear of TiC-Cubic BN Tools”, Mater. Sci. Eng., Vol. 105/106, pp 429- 433. [5] Klimenko, S.A., Mukovoz, Y.A., Lyashko, V.A., Vashchenco, A.N., Ogorodnik, V.V., (1992), “On the Wear Mechanism of Cubic Boron Nitride Base Cutting Tools”, Wear, Vol. 157, pp 1-7. [6] Narutaki, N., Yamane, Y., (1979), “Tool Wear and Cutting Temperature of CBN Tools in Machining of Hardened Steels”, Ann. CIRP, Vol. 28, pp 23-28. [7] Takastu, S., Shimoda, H., Otani, K., (1983), “Effect of CBN Content on the Cutting Performance of Polycrystalline CBN Tools”, Int. J. Refr. Hard Met., Vol. 12, pp. 175-178. [8] Tlusty, G., (2000), Manufacturing Processes and Equipment, Prentice- Hall, Inc., Upper Saddle River, New Jersey.
Details
| Journal Section | Articles |
|---|---|
| Authors | |
| Publication Date | June 15, 2009 |
| Submission Date | October 22, 2017 |
| Published in Issue | Year 2009 Volume: 1 Issue: 2 |
All Rights Reserved. Kırıkkale University, Faculty of Engineering and Natural Science.