Effect of Wear on the Microstructure of Recycled Al –Si Pistons

Yıl 2020, Cilt: 3 Sayı: 2, 45 - 51, 15.12.2020

Blessıng Ngozı Goodluck Alıemeke , M. Oladeinde

Öz

Wear has a tendency of initiating adverse conditions in an automobile engine system. The piston is an important engine component which withstands severe thermal stresses in an engine. Scrap pistons which constitute environmental nuisance will be recycled. A reduced value of wear rate of the pistons determined to be 1.15µg/m was noticed to have an improved microstructure which retains toughness and hardness required for optimal working condition. While wear rate high value of 6.04µg/m yielded micrograph of pistons which produced less pronounced needle shaped eutectic silicon paricles. The micrographs of the aluminium alloy cast piston produced from scraps generator pistons. The result shows primary α-aluminium particles at the background of the structural matrix of the piston alloy. Also, needle shaped near eutectic silicon particles are noticed to be dispersed in the microstructure of the imported piston alloys.

Anahtar Kelimeler

Wear rate, , Microstructure, Micrograph

Proje Numarası

1

Kaynakça

• [1] G. Agarwal, A. Parnaik and R. K. Sharma,” Parametric Optimization and Three-BodyAbrasive Wear Behavoir of Sic Filled Chopped Glass Fiber Reinforced Epoxy Composites”, International Journal of Composite Materials, Vol. 3, No.2, 2013, pp.32-38..
• [2] H. A. Ameen, K. S. Hassan and E. M. Mubarak, Effect of loads, Sliding Speeds and Times on the Wear rate for Different Materials. American Journal of Scientific and Industrial Research Vol.2, No.1, 2011, pp. 99-106.
• [3] Z. Hassan, R. K. Pandey, and D. K. Sehgal, “Wear characteristics in Al-SiC Particulate Composites and the Al-Si Piston Alloy”, Journal of Minerals and Materials Characterization and Engineering, Vol.10, No.14, 2011, pp.1329-1335, 2011.
• [4] K. A. Dell, Metallurgy Theory and Practical Textbook. American Technical Society, Chicago, 2009.
• [5] J. Heuer, “Development and Testing of Carbon Pistons”, Structured Materials Research Institute, Stuggart, Germany, 2015.
• [6] L. J. Yang, “The Effect of Casting Temperature on the Properties of Squeeze Cast Aluminium and Zinc Alloys”, Journal of Materials Processing Technology, Vol. 2, No. 14, 2003, pp. 391-396.
• [7] W. S. Ebhota, E. Ademola, J. Abdulrahman, S. C. Aduloju and O. B. Owolabi, “Designing for domestication of Yamaha CY80 Engine Piston Manufacturing Technology and Evaluation of Aluminium Alloy for Functionality”, International Journal of Advanced Scientific and Technical Research, Vol. 1, No. 5, 2015, pp. 21-34.
• [8] P. Tsushima-Naka, “An Investigation into Solidification and Mechanical Properties Behaviour of Al-Si Casting Alloy”, International Journal of Mechanical and Mechatronics Engineering, Vol. 10, No.4. 2010, pp. 21-30.
• [9] J. R. Davis,. Aluminium and Aluminium Alloys. ASM International Handbook, pp. 3-8, 1993
• [10] V. K. Manchanda, and G. B. S Narang, Materials and Metallurgy. (6th Edition), Khanna Publishers, 2005.
• [11] J. A. Ajayi, “Carbon Steels in Structure and Properties of Engineering Alloys”, Materials Science and Engineering , vol. 391, 2013, pp. 296–304.
• [12] V. J. Patel, “Tribological Investigation of LM 13 by Horizontal Centrifugal Casting Process”, Doctoral Dissertation, Ganpat University, North Gujarat, 2014. [13] T. P. Kayser and B. Svendsen “Experimental and theoretical investigation on the microstructure of aluminum alloys during extrusion”. PAMM, Vol. 8, pp. 10431–10432, 2008.
• [14] R. Kumar and C. Grewal,. Improvement in Hardness of LM-6 Aluminium Green sand Castings by Taguchi Method. Asian Journal of Engineering and Applied Technology,Vol.2, No.2, 2013, pp.11-18.
• [15] T. P. Kayser, F. Klusemann and B. Svendsen, “Experimental and theoretical investigation of the microstructural evolution in aluminium alloys during extrusion”, Computational Methods and Experiments in Materials Characterization, Vol. 4, pp. 209–216, New Forest, UK, 2009.
• [16] F. U. Ozioko, “Synthesis and Study on Effect of Parameters on Dry Sliding Wear Characteristics of Al-Si Alloys”, Leonardo Electronic Journal of Practices and Technologies, Vol. 20, 2012, pp.39-48. [17] T. O. Mbuya, B. O. Odera, S. P. Ng’ang’a and F. M. Oduori ,” Effective Recycling of Cast Aluminium Alloys for Small Foundries”, Recycling for foundries, Vol. 12, No. 2, 2010 pp. 162 – 182.