DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ

Damla Kara; Burcu Günal

doi:10.17567/ataunidfd.522573

DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ

Öz

Amaç: Bu çalışmanın amacı iki farklı sprey dezenfektan kullanımının elastomerik ölçü maddelerinin boyutsal stabilitesi üzerine etkisinin in vitro olarak incelenmesidir.

Gereç ve Yöntem: Çalışmamızda 3 farklı ölçü mad- desi (polieter, kondensasyon tip silikon ve ilave tip silikon) ve iki farklı sprey dezenfektan (Zeta 7: isop- ropanol esaslı ve Descosept: kuarterner amonyum bileşikleri esaslı) kullanıldı. Ölçülerin alınması için pas- lanmaz çelik model kullanıldı ve her bir ölçü madde- sinden 30 adet olacak şekilde, toplam 90 adet ölçü elde edildi. Her bir ölçü maddesi için 10’ar örnek içeren 3 grup oluşturuldu. Zeta 7 ve Descosept sprey uygulanan gruplar 15 dakika bekletildi ve akan su altında yıkandı. Diğer grup ise kontrol grubu olarak kullanıldı. Ölçülere sert alçı dökülerek modeller elde edildi. Hazırlanan alçı modeller üç boyutlu bir dental tarama cihazında taranarak dijital görüntüleri oluşturuldu. Elde edilen dijital model görüntüleri üzerinde cihazın kendi yazılımı kullanılarak referans noktaları arasında lineer ölçümler yapıldı.

Bulgular: Elde edilen verilerin istatistiksel analizi SPSS 22.0 programı kullanılarak yapılmıştır. Verilerin normal dağılıma uyup uymadığı Shapiro-Wilk testi ile kontrol edil- miş ve verilerin normal dağılıma uyması nedeniyle para- metrik test kullanılmıştır. İki farklı dezenfektan materya- linin, farklı ölçü materyalleri üzerindeki boyutsal stabilite- sine olan etkisinin değerlendirilmesi için independent t testi kullanılmıştır. Sonuçlar %95’lik güven aralığında değerlendirilmiştir.

Sonuç: Kondanse silikon grubunda her iki kimyasal dezenfektan ajanında boyutsal değişim açısından ista- tistiksel olarak anlamlı fark gözlemlenmiştir (p<0,05). Polieter ve ilave tip silikon gruplarında her iki kimyasal dezenfektan ajanı uygulaması sonucu boyutsal stabilite açısından istatistiksel olarak anlamlı fark gözlemlen- memiştir (p<0,05).

Anahtar Kelimeler: çapraz enfeksiyon, dezenfektan, ölçü dezenfeksiyonu

IN VITRO EVALUATION OF THE EFFECT OF DISINFECTION PROCEDURES ON DIMENSIONAL STABILITY OF ELASTOMERIC IMPRESSION MATERIALS

ABSTRACT

Aim: The aim of this study was to determine the effect of spray disinfection procedures on the dimensional stability of elastomeric impression materials.

Material and Methods: In our study, we used 3 different impression materials (polyether, condensation type silicone and additional type silicone) and two different spray disinfectants (Zeta 7: based on isopropanol and Descosept: based on quaternary ammonium compounds). A stainless steel model was used for taking measurements and at each to be 30, a total of 90 measurements was obtained. For each impression materials, 3 groups of 10 samples were formed. Zeta 7 and Descosept sprayed groups were left for 15 minutes and washed under running water. The other group was used as the control group. Molds were filled with hard gypsum plaster. Dimensional stability were evaluated using a three-dimensional dental scanning device. Linear measurements were made between the reference points on the digital model images using the device's own software.

Results: Statistical analysis was performed using the SPSS 22.0 program. The data was controlled by the Shapiro-Wilk test and parametric test was used because of the normal distribution of the data. Independent t test was used to assess the effect of disinfection procedures on dimensional stability of elastomeric impression materials. The results were evaluated in 95% confidence interval.

Conclusion: There was statistically significant difference in the mean values of dimensional stability in condensation type silicone (p<0,05). There was no statistically significant difference in the mean values of dimensional stability in polyether and additional type silicone (p<0,05).

Key Words: cross infection, disinfectant, disinfection of impression

Anahtar Kelimeler

çapraz enfeksiyon,dezenfektan

Kaynakça

1. Chau VB, Saunders TR, Pimsler M, Elfring DR. In-depth disinfection of acrylic resins. J Prosthet Dent 1995;74:309-13.
2. Powell GL, Runnels RD, Saxon BA, Whisenant BK. The presence and identification of organisms transmitted to dental laboratories. J Prosthet Dent 1990;64: 235-7.
3. Gerhardt DE, Sydiskis RJ Impression materials and virüs. J Am Dent Assoc 1991;122: 51-4.
4. Rice CD, Dykstra MA, Gier RE, Cobb CM. Microbial contamination in four brands of irreversible hydrocolloid impression materials. J Prosthet Dent 1991;65:419-23.
5. Samaranayake LP, Hunjan M, Jennings KJ. Carriage of oral flora on irreversible hydrocolloid and elastomeric impression materials. J Prosthet Dent 1991;65: 244-9.
6. Mitchell DL, Hariri NM, Duncanson MG Jr, Jacobsen NL, McCallum RE. Quantitative study of bacterial colonization of dental casts. J Prosthet Dent 1997;78:518-21.
7. McNeil MR, Coulter WA, Hussey DL. Disinfection of irreversible hydrocolloid impressions: a comprative study. Int J Prosthodont 1992;5:563-7.
8. Beyerle MP, Hensley DM, Bradley DV Jr, Schwartz RS, Hilton TJ. Immersion disinfection of irreversible hydrocolloid impressions with sodium hypochlorite. Part 1: microbiology. Int J Prosthodont 1994; 7:234-8.

9. Vayısoğlu Özcan A, Nalbant L, Nalbant D. Protetik diş tedavisinde dezenfeksiyon ve sterilizasyon. Atatürk Üniv Diş Hek Fak Derg 2016; 26: 169-79.
10. Vandewalle KS, Charlton DG, Schwartz RS, Reagan SE, Koeppen RG. Immersion disinfection of irreversible hydrocolloid impressions with sodium hypochlorite. Part II: effect on gypsum. Int J Prosthodont 1994;7:315 - 22.
11. Lepe X, Johnson GH, Berg JC. Surface characte- ristics of polyether and addition silicone impression materials after long term disinfection. J Prosth Dent 1995;74:181-6.
12. Hilton TJ, Schwartz RS, Bradley DV. Immersion disinfection of irreversible hydrocolloid impressions. Part 2: effects on gypsum casts. Int J Prosthodont 1994;7:424-33.
13. Matyas J, Dao N, Caputo AA, Lucatorto FM. Effects of disinfectants on dimensional accuracy of impression materials. J Prosth Dent 1990;64:25 - 31.
14. Council on Dental Materials, Instruments and Equipment. Disinfection of impression. J Am Dent Assoc 1991;122: 110
15. Kohn WG, Harte JA, Malvitz DM, Collins AS, Cleveland JL, Eklund KJ Guidelines for infection control in dental health care settings. J Am Dent Assoc 2004;135: 33-47
16. ADA Council on Scientific Affairs and ADA Council on Dental Practice.Infection control recommen- dations for the dental office and the dental laboratory. J Am Dent Assoc 1996;127:672-80.
17. Owen CP, Goolam G. Disinfection of impression materials to prevent viral cross contamination: a review and a protocol. International J Prosthod 1993;6:480–94.
18. Gerhardt DE, Williams HN. The affecting and stability of sodium hypochlorite solutions used to disinfect dental impressions. Quintessence Int 1991;22:587–91.
19. Sofou A, Larsen T, Fiehn N-E, Öwall B. Contamination level of alginate impression arriving at a dental laboratory. Clin Oral Invest 2002;6:161-5.
20. Hisako, Masahiro, Hideharu, Takayuki. Effect of immersion disinfection of alginate impressions in sodium hypochlorite solution on the dimensional changes of stone models Dent Material J 2012; 31: 280–286
21. Council on Dental Materials, Instruments and Equipment, the Council on Dental and Practise, Council on Dental Therapeutic Infection control recommedation fort he dental office and the dental laboratory. J Am Dent Assoc 1988;116:241-8.
22. Jagger DC, Hugget R, Harrison A. Cross-infection control in dental laboratories. Br Dent J 1995;179:93-6.
23. Kugel G, Perry RD, Ferrari M, Lalicata P. Disinfection and communication practise: asurvey of U.S dental laboratories. J Am Dent Assoc 2000;131:786-92.
24. Kern M, Rathmer R, Strub JR. Three-dimensional investigation of the accuracy of impression materials after disinfection. J Prosthet Dent 1993;70:449-56.
25. Holtan JR, Olin PS, Rudney JD. Dimensional stability of a polyvilylsiloxane impression material following ethylene oxide and steam autoclave sterilization. J Prosthet Dent 1991; 65:519-25.
26. Abdelaziz KM, Hassan AM, Hodges JS. Reproducibility of sterilized rubber impressions. Braz Dent J 2004;15:209-13.
27. Hiraguchi H, Uchida H, Nakagawa H, Tanabe N, Habu H. Effects of immersion disinfection of vinyl silicone rubber impressions on reproducibility of stone models. J Dent Mate 1999;18:18-4.
28. Ünlü A, Kaya F, Öktemer M. Investigation of the effect of disinfectant solution on silicone impression materials wettability. Turkiye Klinikleri J Dental Sci 1997; 3: 30-4.
29. Chia WK, Stevens L, Basford KE, Randell DM. Dimensionalchange of impressions on sterilization. Aust Dent J 1990;35:23-6.
30. Kotsiomiti H, Totsika A, Diakoyianni-Mordohai H, Kaloyiannides A. The influence of antiseptic solutions used against AIDS on dental waxes, shellac bases, impression compound and zinc-oxide eugenol paste. Hell Stomatol Chron 1989;33:149-57.
31. Sofou A, Larsen T, Owall B, Fiehn NE. In vitro study of transmission of bacteria from contaminated metal models to stone models via impressions. Clin Oral Investig 2002;6:166-70.
32. Boden J, Likeman P, Clark R. Some effects of disinfecting solutions on the properties of alginate impression material and dental stone. Eur J Prosthodont Restor Dent 2001;9:131-5.
33. Taylor RL, Wright PS, Maryan C. Disinfection procedures: their effect on the dimensional accuracy and surface quality of irreversible hydrocolloid impression materials and gypsum casts. Dent Mater 2002;18:103-10
34. Johnson GH, Drennon DG, Powel GL. Accuracy of elastomeric impressions disinfected by immersion. J Am Dent Assoc 1988;116: 525-30.
35. Durr DP, Novak EV. Dimensional stability of alginate impressions immersed in disinfecting solutions. ASDC J Dent Child 1987;54:45- 8.
36. al-Omari WM, Jones JC, Wood DJ. The effect of disinfecting alginate and addition cured silicone rubber impression materials on the physical properties of impressions and resultant casts. Eur J Prosthodont Restor Dent 1998;6:103-10.
37. Al-Jabrah O, Al-Shumailan Y, Al-Rashdan M. Antimicrobial effect of 4 disinfectants on alginate, polyether, and polyvinyl siloxane impression materials. Int J Prosthodont. 2007; 20: 299-307.
38. Suprono SM, Kattadiyil TW, Goodacre CJ, Winer MS. Effect of disinfection on irreversible hydrocolloid and alternative impression materials and the resultant gypsum casts. J Prosthet Dent 2012; 108:250-8.
39. Yilmaz H, Aydin C, Gul B, Yilmaz C, Semiz M. Effect of disinfection on the dimensional stability of polyether impression materials. J Prosthodont 2007; 16: 473-9.
40. Kaplan BA, Goldstein GR, Boylan R. Effectiveness of a professional formula disinfectant for irreversible hydrocolloid. J Prosthet Dent 1994;71: 603-6.
41. Drennon DG, Johnson GH, Powell GL. The accuracy and efficacy of disinfection by spray atomization on elastomeric impressions. J Prosthet Dent 1989;62:468-75.
42. Olsson S, Bergman B, Bergman M. Agar impression materials, dimensional stability and surface detail sharpness following treatment with disinfectant solutions. Swed Dent J 1987;11:169-77.
43. Tan HK, Hooper PM, Buttar IA, Wolfaardt JF. Effects of disinfecting irreversible hydrocolloid impressions on the resultant gypsum casts: Part II--Dimensional changes. J Prosthet Dent 1993; 70:532-7.
44. Kotsiomiti E, Tzialla A, Hatjivasiliou K Accuracy and stability of impression materials subjected to chemical disinfection - a literature review. J Oral Rehabil 2008;35:291-9.
45. Bock JJ, Fuhrmann RA, Setz J. The influence of different disinfectants on primary impression materials. Ouintessence Int 2008; 39: 93-8.
46. Adabo GL, Zanarotti E, Fonseca RG, Cruz CA. Effect of disinfectant agents on dimensiol stability of elastomeric impression materials. J Prosthet Dent 1999; 81:621-4
47. N. Martina, M.V. Martinb, N.M. Jedynakiewicz The dimensional stability of dental impression materials following immersion in disinfecting solutions dental materials 2007;23:760–8.
48. Bilgin T, Kutay Ö, İnce Ö . dezenfeksiyon ve sterilizasyonun silikon esaslı ölçü maddelerinin boyutsal değişimlerine etkileri. İ Ü Diş Hek Fak Derg 1993;27:181-6.
49. Walker MP, Rondeau M, Petrie C, Tasca A, Williams K. Surface quality and long-term dimensional stability of current elastomeric impression materials after disinfection. J Prosthod 2007; 16: 343-51.
50. Melilli D, Rallo A, Cassaro A, Pizzo G. The effect of immersion disinfection procedures on dimensional stability of two elastomeric impresion materials. J Oral Sci 2008;50 :441-6.
51. Thouati A, Deveaux E, Iost A, Behin P. Dimensional stability of seven elastomeric impression materials immersed in disinfectants. J Prosthet Dent 1996;76:8-14.

Ayrıntılar

Birincil Dil

Türkçe

Konular

Sağlık Kurumları Yönetimi

Bölüm

Araştırma Makalesi

Yazarlar

Damla Kara Bu kişi benim
0000-0002-7853-9634

Burcu Günal Bu kişi benim
0000-0001-5098-1765

Yayımlanma Tarihi

15 Ocak 2019

Gönderilme Tarihi

10 Şubat 2017

Kabul Tarihi

18 Ağustos 2017

Yayımlandığı Sayı

Yıl 2019 Cilt: 29 Sayı: 1

DOI

https://doi.org/10.17567/ataunidfd.522573

IZ

https://izlik.org/JA67ST53UK

Kaynak Göster

RIS / Bibtex

APA

Kara, D., & Günal, B. (2019). DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ. Atatürk Üniversitesi Diş Hekimliği Fakültesi Dergisi, 29(1), 12-19. https://doi.org/10.17567/ataunidfd.522573

AMA

1.Kara D, Günal B. DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ. Ata Diş Hek Fak Derg. 2019;29(1):12-19. doi:10.17567/ataunidfd.522573

Chicago

Kara, Damla, ve Burcu Günal. 2019. “DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ”. Atatürk Üniversitesi Diş Hekimliği Fakültesi Dergisi 29 (1): 12-19. https://doi.org/10.17567/ataunidfd.522573.

EndNote

Kara D, Günal B (01 Ocak 2019) DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ. Atatürk Üniversitesi Diş Hekimliği Fakültesi Dergisi 29 1 12–19.

IEEE

[1]D. Kara ve B. Günal, “DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ”, Ata Diş Hek Fak Derg, c. 29, sy 1, ss. 12–19, Oca. 2019, doi: 10.17567/ataunidfd.522573.

ISNAD

Kara, Damla - Günal, Burcu. “DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ”. Atatürk Üniversitesi Diş Hekimliği Fakültesi Dergisi 29/1 (01 Ocak 2019): 12-19. https://doi.org/10.17567/ataunidfd.522573.

JAMA

1.Kara D, Günal B. DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ. Ata Diş Hek Fak Derg. 2019;29:12–19.

MLA

Kara, Damla, ve Burcu Günal. “DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ”. Atatürk Üniversitesi Diş Hekimliği Fakültesi Dergisi, c. 29, sy 1, Ocak 2019, ss. 12-19, doi:10.17567/ataunidfd.522573.

Vancouver

1.Damla Kara, Burcu Günal. DEZENFEKTAN KULLANIMININ ELASTOMERİK ÖLÇÜ MATERYALLERİNİN BOYUTSAL STABİLİTESİ ÜZERİNE ETKİSİNİN İN VİTRO OLARAK İNCELENMESİ. Ata Diş Hek Fak Derg. 01 Ocak 2019;29(1):12-9. doi:10.17567/ataunidfd.522573