Islatma-Kurutmanın Kraft Kağıt Özellikleri Üzerine Etkileri

Öz

Bu çalışmanın amacı ıslatma-kurutma işlemlerinin ağartılmış kraft kağıtlarının özellikleri üzerine etkilerini araştırmaktır. Elde edilen sonuçlara göre; üç farklı firmadan (A, B ve C tipi) temin edilen kağıt numunelerinin sürekli ıslatılmasının ve kurutulmasının hem fiziksel hem de mukavemet özellikleri üzerinde etkili olduğu anlaşılmıştır. Bununla birlikte, başlangıç aşamaları (5. ıslatma-kurutma aşamasına kadar) yüksek derecede modifikasyon ile sonuçlanan dramatik etkilere sahipken sonraki her aşamanın fiziksel özellikler üzerinde ılımlı bir eğilim olduğu gözlemlenmiştir.
Islatma-kurutma işlemi devam ederken azalan kopma uzunluğu ve patlama indeksinin aksine, yırtılma indeksi her iki yönde de değişmiştir (artar veya azalır). Bununla birlikte, numunelerin ıslatma-kurutma işlemleriyle kopma uzunluğunun %11.4 ile %67.8 aralığında azaldığı bulunmuştur. En düşük kopma uzunluğu 8. döngü aşamasında 1.79 km olan B tipi kağıtlarda gözlenmiştir. En düşük yırtılma indeksinin C tipi kağıtların 5. ıslatma-kurutma aşamasından sonra 2.64 mN.m2/gr değerinde olduğu, en yüksek yırtılma indeksinin ise B tipi kağıtların 6. ıslatma-kurutma aşamasında 5.62 mN.m2/gr değerinde olduğu tespit edilmiştir. Islatma-kurutma işlemi sırasında kağıt yapısının hasar gördüğü ve bağlanma potansiyellerinin azaldığı açıkça anlaşılmaktadır.

Anahtar Kelimeler

• Kağıt
• ıslatma
• kurutma
• fiziksel
• mukavemet

A Study on Effects of Wetting-Drying on Bleached Kraft Paper Properties

Öz

The aim of the study is to investigate effects of wetting-drying processes on bleached kraft paper properties. According to results; it has been realized that continuously wetting-drying of paper samples supplied from three different brand (A, B, and C types) effect on both physical and strength properties. However, initial stages (up to 5th cycling stages) have dramatic effects resulting in a high degree of modification, considering the fact that each following stage is moderate trend on physical properties.
Contrary to breaking length and burst index that have a reducing trend as wetting-drying in progress, the tear index changed in both directions (increases or decreases). However, breaking length of samples were found to be reduced range of 11.4% to 67.8%. Nevertheless, the lowest breaking length was observed B type of papers with 1.79 km at 8th cycling stage. The lowest tear index of 2.64 mN.m2/gr was found at 5th cycling stage for C type papers while the highest tear index of 5.62 mN.m2/gr was found at 6th cycling stage for B type papers. It is clearly realized that the paper network structure are damaged and bonding potentials reduced during the wetting-drying process. 

Anahtar Kelimeler

• Paper
• wetting
• drying
• physical
• strength

Kaynakça

1. 1. Atalla, R.H. (1992). Structural change in cellulose during papermaking and recycling, Materials Research Society Symposium, 229-236, April 27-29, San Francisco, CA.
2. 2. Çiçekler, M. (2019). Birincil ve Ikincil Lif Karişimlarinin Yazi Tabi, Oluklu Mukavva Ve Gazete Kağidi Üretiminde Kullaniminin Araştirilmasi (In Turkish), Doctoral dissertation, Kahramanmaraş Sütçü İmam University, Kahramanmaraş, Turkey.
3. 3. Clark, J.D.A. (1985). Pulp Technology and Treatment for Paper. San Francisco, California: Miller Freeman Publications, Inc. NY, 878 pages.
4. 4. Goring, D.A.I. (1978). The effect of cellulose on the structure of water, TAPPI Annual Meeting, March 6-8, Conrad Hilton Hotel, Chicago.
5. 5. Howard, R.C. (1990). The effects of recycling on paper quality, Journal of Pulp and Paper Science, 16(9): 143-149.
6. 6. Howard, R.C., Bichard, W. (1992). The basic effects of recycling on pulp properties, Journal of Pulp and Paper Science, 18(4): 151-159.
7. 7. Hubbe, M.A. 2007. Paper’s resistance to wetting-A review of internal sizing chemicals and their effects, BioResources, 2(1): 106–145.
8. 8. ISO 5636-4 (2013). Paper and board - Determination of air permeance (medium range) - Part 4: Sheffield method, International Organization for Standardization, Geneva, Switzerland.

9. 9. ISO 8791-2 (2013). Paper and board - Determination of roughness/smoothness (air leak methods) - Part 2: Bendtsen method, International Organization for Standardization, Geneva, Switzerland.
10. 10. Latifah, J., Ainun, Z.M.A., Rushdan, I., Mahmudin, S. (2009). Restoring strength to recycled fibres by blending with kenaf pulp, Malaysian Journal of Science, 28(1): 78-87.
11. 11. Li, Y., Nanri, Y., Douglas, W.J.M., Vera, J.H. (1994). Equilibrium moisture content of cellulosic materials at high temperature, Drying Tech., 12(4): 823-847.
12. 12. Lovaglio, T., Gindl-Altmutter, W., Meints, T., Moretti, Todaro, L. (2019). Wetting behavior of Alder (Alnus cordata (Loisel) Duby) wood surface: effect of thermo-treatment and Alkyl Ketene Dimer (AKD), Forests, 10:770-786.
13. 13. McKee, R. (1971). Effect of repulping on sheet properties and fiber characteristics. Paper Trade J., (May 24): 34-40.
14. 14. McKenzie, A.W. (1984). The structure and properties of paper Part XXI: The diffusion theory of adhesion applied to interfibre bonding, Appita, 37(7): 580-583.
15. 15. Nanko, H., Asano, S., Ohsawa, J. (1991). Shrinking behavior of pulp fibers during drying, International Paper Physic Conference, January, Book 2, Kailua Kona, HI, pp: 365-373.
16. 16. Nazhad, M.M. (2005). Recycled fibre quality–A review, Journal of industrial and engineering chemistry, Korean Journal, 11(3): 314.
17. 17. Pesman, E., Laloglu, S. (2018). Recycling of colored office paper. Part I: Pre-bleaching with Formamidine Sulfinic Acid at pulper, Bioresources, 13(2): 3949-3957.
18. 18. Roberts, J.C. (1996). Paper Chemistry, 2nd Ed., Blackie, Glasgow and London; USA, Chapman and Hall, New York, 267 pages.
19. 19. Sahin, H. (2013). A study on paper recycling effects on cellulose properties, (Turkish, Abstract in English) SDU Faculty of Forestry Journal, 14(1): 74-80.
20. 20. Sahin, H.T. (2009). The effects of waste paper properties on recycling, (Turkish, Abstract in English) Artvin Coruh University Journal of Forestry Faculty, 10(2), 117-123.
21. 21. Sahin, H.T., Arslan, M.B. (2008). A study on physical and chemical properties of cellulose paper immersed in various solvent mixtures, International Journal of Molecular Sciences, 9(1): 78-88.
22. 22. Scott, W.E., Abbott, J.E. (1995). Properties of Paper: An Introduction, Tappi Press, Atlanta, GA. 174 pages.
23. 23. Singh, S., Roy, D.N. (1996). The Effects of recycling on the chemical properties of thermomechanical pulp, J. Wood Chem. & Tech., 16(4): 421-437.
24. 24. Smook, G.A. (2002). Handbook for Pulp and Paper Technologists, 3rd Ed., Angus Wilde Publications, Canada, 425 pages.
25. 25. Sood, Y.V., Pande, P.C., Tyagi, S., Payra, I., Kulkarni, N., Kulkarni, A.G. (2005). Quality improvement of paper from bamboo and hardwood furnish through fiber fractionation, Journal of Scientific & Industrial Research, 64: 299-305.
26. 26. Sutjipto, E.R., Li, K., Pongpattanasuegsa, S., Nazhad, M.M. (2008). Effect of recycling on paper properties. Tappsa Journal (Technical Article), Reached at: 03.03.2020; http://www.tappsa.co.za/archive3/Journal_papers/Effect_of_recycling_on_paper_p/
27. 27. TAPPI T402 (2013). Standard conditioning and testing atmosphere for paper, board, pulp handsheets, and related products, Technical Association of Pulp and Paper Industry, Atlanta, USA.
28. 28. TAPPI T403 (2015). Bursting strength of paper, Technical Association of Pulp and Paper Industry, Atlanta, USA.
29. 29. TAPPI T411 (2015). Thickness (Caliper) of paper, paperboard, and combined board, Technical Associationof Pulp and Paper Industry, Atlanta, USA.
30. 30. TAPPI T414 (2013). Internal tearing resistance of paper (Elmendorf-type method), Technical Association of Pulp and Paper Industry, Atlanta, USA.
31. 31. TAPPI T441 (2013). Water absorptiveness of sized (non-bibulous) paper, paperboard, and corrugated fiberboard (Cobb test), Technical Association of Pulp and Paper Industry, Atlanta, USA.
32. 32. TAPPI T494 (2006). Tensile properties of paper and paperboard, Technical Association of Pulp and Paper Industry, Atlanta, USA.
33. 33. Wistara, N., Raymond, A. (1999). Properties and treatments of pulps from recycled paper, Part I. Physical and chemical properties of pulps, Cellulose, 6:291-324.
34. 34. Yeo, J., Lee, J., Hwang, S. (2017). Effects of lignin on the volume shrinkage and mechanical properties of a styrene/unsaturated polyester/lignin ternary composite system, Composites Part B: Engineering, 130(1): 167-173.