Optimization of Polyethylene Inserts Design Geometry of Total Knee Prosthesis

Yıl 2018, Cilt: 2 Sayı: 2, 31 - 39, 31.12.2018

Burak Öztürk Levent Uğur Fehmi Erzincanlı Özkan Küçük

Öz

Knee prostheses are produced from biomaterials which are compatible with human body as a result of damage of cartilage tissue due to various health problems. These prostheses consist of polyethylene parts between the Tibial Component and the femoral component of the femur. Polyethylene insert is used to reduce wear mechanisms between both materials. In this study, design library design parameters required for obtaining a polyethylene insert design were determined. These design parameters were modeled in the Solid Works Computer Aided Design (CAD) Program according to the L27 experiment design for each design parameter S / N ratios for three different levels using the Taguchi Method. For the safety coefficient analysis of each design, maximum forces in the literature were determined and implemented in Ansys Computer Aided Engineering (CAE) Program. According to the results of this analysis, maximum stress, weight and safety coefficient changes of each design geometry were determined. S / N ratios and% effects of each design parameter were determined by applying Taguchi and Variance Analysis. According to these results, the design is optimized by selecting the levels of each design parameter for the minimum weight and maximum safety factor. On the other hand, stress change graphs were obtained in different sections of the design. In the literature, for the first time, the design geometry of the polyethylene part was modeled by parametric design and optimum design was obtained.

Anahtar Kelimeler

Arthroplasty, Optimization in Design, Polyethylene Insert, Computer Aided Design (CAD), Computer Aided Engineering (CAE)

Optimization of Polyethylene Inserts Design Geometry of Total Knee Prosthesis

Öz

Knee prostheses are produced from biomaterials which
are compatible with human body as a result of damage of cartilage tissue due to
various health problems. These prostheses consist of polyethylene parts between
the Tibial Component and the femoral component of the femur. Polyethylene
insert is used to reduce wear mechanisms between both materials. In this study,
design library design parameters required for obtaining a polyethylene insert
design were determined. These design parameters were modeled in the Solid Works
Computer Aided Design (CAD) Program according to the L27 experiment design for
each design parameter S / N ratios for three different levels using the Taguchi
Method. For the safety coefficient analysis of each design, maximum forces in
the literature were determined and implemented in Ansys Computer Aided
Engineering (CAE) Program. According to the results of this analysis, maximum
stress, weight and safety coefficient changes of each design geometry were
determined. S / N ratios and% effects of each design parameter were determined
by applying Taguchi and Variance Analysis. According to these results, the
design is optimized by selecting the levels of each design parameter for the
minimum weight and maximum safety factor. On the other hand, stress change
graphs were obtained in different sections of the design. In the literature,
for the first time, the design geometry of the polyethylene part was modeled by
parametric design and optimum design was obtained.

Anahtar Kelimeler

Arthroplasty, Optimization in Design, Polyethylene Insert, Computer Aided Design (CAD), Computer Aided Engineering (CAE)

Kaynakça

• [1] S. Boran C. Hurson K. Synnott P. Keogh, ‘’Biomechanical analysis of tibial tray fractures post total knee Arthroplasty’’, Eur J Orthop Surg Traumatol, 15, 295–299, 2005
• [2] C. Luring L. Perlick T. Schubert M. Tingart, ‘’A rare cause for knee pain: fracture of the femoral component after TKR. A case report’’, Knee Surg Sports Traumatol Arthrosc, 15, 756–757, 2007
• [3] M. Wada , S. Imura, A. Bo, H. Baba, T. Miyazaki, ‘’Stress fracture of the femoral component in total knee replacement’’, International Orthopaedics (SICOT ), 21, 54–55, 1997
• [4] Cameron H., Welsh R. ‘’Fracture of the femoral component in unicompartmental total knee arthroplasty’’, J Arthroplasty , 5, 31–317, 1990
• [5] Moreland JR, ‘’Fracture of a unicompartmental knee replacement femoral component’’, Clin Orthop 206, 166–168, 1986
• [6] Sandborn P., Cook S., Kester M., Haddad R., ‘’Fatigue failure of the femoral component of a unicompartmental knee’’, Clin Orthop,, 222, 249–254, 1987
• [7] Konstantinos P., Claire M., Petra K., Peter G., ‘’Fracture of the femoral component of a Brigham unicompartmental knee: a case report’’, Knee Surg Sports Traumatol Arthrosc, 12, 307–310, 2004
• [8] Küçük Ö., Öztürk B., Development Of Design Geometry Of Aluminum Fittings For Healthy And Safety Sanıtary Installatıons, Journal of Environmental Protectionand Ecology, 18-2, 776–787, 2017
• [9] Küçük Ö., Öztürk B., Varhan S, “Investigation of the design parameters affecting the safety factor in fittings by using Taguchi method”, The Turkish Journal of Occupational / Environmental Medicine and Safety, Volume: The 2nd international Water and Health Congress -Issue: The 2nd international Water and Health Congress, , 0-10, 2017
• [10] Mark L. Morrison, Shilesh J. and Amit P., ‘’Design of an Advanced Bearing System for Total Knee Arthroplasty, Lubricants’’, 3, 475-492, 2015
• [11] B.R. Rawala, Amit Y., Vinod P., ‘’Life estimation of knee joint prosthesis by combined effect of fatigue and wear’’, Procedia Technology, 23, 60 – 67, 2016
• [12] Tomaso V., Francesco M., Dario G., Maurizio C., Riccardo P., ‘’Contact stresses and fatigue life in a knee prosthesis: comparison between in vitro measurements and computational simulations’’, Journal of Biomechanics, 37, 45–53, (2004)