Analysis of Kinematic and Kinetic Parameters during Manual Load Lifting Using Markerless Motion Capture and Inverse Dynamics Method

Öz

Manual material handling activities continue to be a primary cause of musculoskeletal disorders in industrial environments. This study aimed to perform a biomechanical moment analysis of symmetric load lifting using kinematic data obtained via markerless motion capture technology without the use of physical sensors. Ten healthy male volunteers performed squat lifting tasks in the sagittal plane under external loads of 2.5 kg, 5.0 kg and 7.5 kg. Joint angle, velocity, and acceleration data were acquired using the MediaPipe Holistic algorithm. These data were combined with anthropometric constants to calculate joint moments using the inverse dynamics method via Newton-Euler equations. The results revealed that increased external load significantly elevated peak moment values in the hip, shoulder, and elbow joints. Specifically, as the load increased from 2.5 to 7.5 kg, normalized peak hip moments rose from 1.94 to 2.33 Nm/kg, shoulder moments from 0.30 to 0.58 Nm/kg, and elbow moments from 0.11 to 0.26 Nm/kg. In contrast, ankle and knee joint moments showed relatively small changes. Additionally, participants anthropometric differences influenced their lifting strategies, resulting in notable variations in shoulder and elbow kinematics during the load-centering and stabilization phases. In conclusion, this methodology demonstrates that ergonomic risks and mechanical joint stresses during manual material handling tasks can be practically analyzed in a non-invasive manner, independent of laboratory constraints.

Anahtar Kelimeler

• Biomechanics
• Inverse dynamics
• Markerless motion capture
• Manual load lifting
• Joint moment

Etik Beyan

The authors confirm that the ethical policies of the journal, as noted on the journal's author guidelines page, have been adhered to. Ethics committee approval for the acquisition of the data used in this study was obtained from the Faculty of Science and Engineering Ethics Committee Presidency (Approval date: September 29, 2022, protocol code: 22/9).

Teşekkür

This study is partially based on the doctoral thesis authored by the first author at Atatürk University.

Kaynakça

1. Amprimo, G., Masi, G., Pettiti, G., Olmo, G., Priano, L., & Ferraris, C. (2024). Hand tracking for clinical applications: Validation of the Google MediaPipe Hand (GMH) and the depth-enhanced GMH-D frameworks. Biomedical Signal Processing and Control, 96, 106508.
2. Ayoub, M., & Woldstad, J. C. (1999). Models in manual materials handling. Biomechanics in ergonomics, 267-305.
3. Bazarevsky, V., Grishchenko, I., Raveendran, K., Zhu, T., Zhang, F., & Grundmann, M. (2020). Blazepose: On-device real-time body pose tracking. arXiv preprint arXiv:2006.10204.
4. Bhamidipati, V. S. P., Saxena, I., Saisanthiya, D., & Retnadhas, M. (2023). Robust intelligent posture estimation for an AI gym trainer using MediaPipe and OpenCV. 2023 International Conference on Networking and Communications (ICNWC) (pp. 1-7). IEEE
5. Ceseracciu, E., Sawacha, Z., & Cobelli, C. (2014). Comparison of markerless and marker-based motion capture technologies through simultaneous data collection during gait: proof of concept. PloS one, 9(3), e87640.
6. Contini, R., Drillis, R. J., & Bluestein, M. (1963). Determination of body segment parameters. Human Factors, 5(5), 493-504.
7. Çil, M. (2026). Vücut segment ataletlerinin ters dinamik yöntemiyle tespiti (Publication No. 1011746) [Doctoral dissertation, Atatürk Üniversitesi]. Ulusal Tez Merkezi.
8. Çil, M., Usanmaz, B., & Gündoğdu, Ö. (2026). An Investigation of Variable Segmental Inertial Parameters in Manual Load Lifting: A Genetic Algorithm-Based Inverse Dynamics Approach. Mathematics, 14(6), 1065.

9. Dempster, W. T. (1955). Space requirements of the seated operator, geometrical, kinematic, and mechanical aspects of the body with special reference to the limbs (WADC-TR-55-159).
10. Dempster, W. T., Gabel, W. C., & Felts, W. J. (1959). The anthropometry of the manual work space for the seated subject. American journal of physical anthropology, 17(4), 289-317.
11. Drillis, R., & Contini, R. (1966). Body segment parameters. New York University, School of Engineering and Science, Research Division.
12. Faber, G., Kingma, I., Chang, C., Dennerlein, J., & Van Dieen, J. (2020). Validation of a wearable system for 3D ambulatory L5/S1 moment assessment during manual lifting using instrumented shoes and an inertial sensor suit. Journal of biomechanics, 102, 109671.
13. Faber, G. S., Chang, C., Kingma, I., Dennerlein, J., & Van Dieën, J. (2016). Estimating 3D L5/S1 moments and ground reaction forces during trunk bending using a full-body ambulatory inertial motion capture system. Journal of biomechanics, 49(6), 904-912.
14. Google AI. (2025). MediaPipe Solutions guide. Google. Retrieved December 25 from https://ai.google.dev/edge/mediapipe/solutions/guide
15. Govaerts, R., Tassignon, B., Ghillebert, J., Serrien, B., De Bock, S., Ampe, T., El Makrini, I., Vanderborght, B., Meeusen, R., & De Pauw, K. (2021). Prevalence and incidence of work-related musculoskeletal disorders in secondary industries of 21st century Europe: a systematic review and meta-analysis. BMC musculoskeletal disorders, 22(1), 751.
16. Hwang, S., Kim, Y., & Kim, Y. (2009). Lower extremity joint kinetics and lumbar curvature during squat and stoop lifting. BMC musculoskeletal disorders, 10(1), 15.
17. Jiang, J., Skalli, W., Siadat, A., & Gajny, L. (2024). Societe de Biomecanique young investigator award 2023: Estimation of intersegmental load at L5-S1 during lifting/lowering tasks using force plate free markerless motion capture. J Biomech, 177, 112422. https://doi.org/10.1016/j.jbiomech.2024.112422
18. Kusunose, M., Inui, A., Mifune, Y., Yamaura, K., Shinohara, I., Tanaka, S., Ehara, Y., Takigami, S., Osawa, S., & Nakabayashi, D. (2025). Estimation of Forearm Pronation–Supination Angles Using MediaPipe and IMU Sensors: Performance Comparison and Interpretability Analysis of Machine Learning Models. Applied Sciences, 15(19), 10527.
19. Kwon, Y., & Kim, D. (2022). Real-time workout posture correction using OpenCV and MediaPipe. The Journal of Korean Institute of Information Technology, 20(1), 199-208.
20. Marras, W., Granata, K., Davis, K., Allread, W., & Jorgensen, M. (1999). Effects of box features on spine loading during warehouse order selecting. Ergonomics, 42(7), 980-996.
21. Robert-Lachaine, X., Mecheri, H., Larue, C., & Plamondon, A. (2017). Validation of inertial measurement units with an optoelectronic system for whole-body motion analysis. Medical & biological engineering & computing, 55(4), 609-619.
22. Robertson, D. G. E., Caldwell, G. E., Hamill, J., Kamen, G., & Whittlesey, S. (2013). Research methods in biomechanics. Human kinetics.
23. Shaharum, S. M., Samsudin, W. S. W., Faudzi, A. A. M., Ghani, N. A., Ching, C. S., & Palaniappan, R. (2024). Enhancing urban wellness: real-time workout posture monitoring with human pose estimation and joint angle analysis using MediaPipe and OpenCV. 8th IET Smart Cities Symposium (SCS 2024) (Vol. 2024, pp. 429-435). IET
24. Taylor, G. A., Easter, K., & Hegney, R. (2004). Enhancing occupational safety and health. Elsevier.
25. The jamovi project. (2025). jamovi. (Version 2.7) [Computer software]. https://www.jamovi.org.
26. Wagh, V., Scott, M. W., & Kraeutner, S. N. (2024). Quantifying Similarities Between MediaPipe and a Known Standard to Address Issues in Tracking 2D Upper Limb Trajectories: Proof of Concept Study. JMIR Formative Research, 8(1), e56682.
27. Wesseling, M., de Groote, F., & Jonkers, I. (2014). The effect of perturbing body segment parameters on calculated joint moments and muscle forces during gait. J Biomech, 47(2), 596-601. https://doi.org/10.1016/j.jbiomech.2013.11.002
28. Winter, D. A. (2009). Biomechanics and motor control of human movement. John wiley & sons.
29. Yanıkören, M., Yılmaz, S., Usanmaz, B., Tezgel, S., Yazar, M., & Gündoğdu, Ö. (2020). Giyilebilir Hareket Sensörü Kullanılarak Dinamik Model ile Üst Uzuv Eklemleri Üzerine Etkiyen Kuvvetlerin ve Torkların Belirlenmesi. Journal of the Institute of Science and Technology, 10(4), 2850-2859.
30. Yanikören, M., Yilmaz, S., Usanmaz, B., & Gündoğdu, Ö. (2026). Analysis of differences in manual material lifting behavior between healthy weight and underweight females. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 09544062261421992.