Static Analysis of the Slotted Upper Plate of Low Pressure Casting Machine

Yıl 2021, Cilt: 17 Sayı: 1, 35 - 41, 30.12.2020

Yasemin Nur Aydın Onur Ozaydin Ahmet Alper Akış

https://doi.org/10.18466/cbayarfbe.779687

Öz

In this study, the process improvement / Kaizen case study of a casting mold set-up process taking an average of 20 minutes, is examined. The aim of this work is reducing the set-up time and improving ergonomic conditions. Since existing operating conditions cause a waste of time and result in non-ergonomic conditions, an air impact wrench had to be used in the mold assembly process. To be able to use the air impact wrench a new geometry had to implemented on casting mold and this design change was analyzed in ANSYS software to avoid a failure in working conditions. It was concluded that the maximum stress on the mold is not at a level where it will cause failure. After the initial geometry improvement process, a further ANSYS-Topology optimization process is conducted to reduce weight of the mold. As a result of this the set-up time decreased to an average of 9 minutes. Consequently, big benefits in terms of cycle time, occupational health and safety, improvement in the process and cost have been achieved.

Anahtar Kelimeler

ANSYS Static Structural, ANSYS Topology Optimization, Case Study, Kaizen, Process Improvement

Kaynakça

• 1. Kabadayı, E. T. 2002. İşletmelerdeki Üretim Performans Ölçütlerinin Gelişimi, Özellikleri ve Sürekli İyileştirme ile İlişkisi. Doğuş Üniversitesi Dergisi; 61-75.
• 2. Joseph C. Chen, Y. L. 2010. From Value Stream Mapping Toward a Lean/sigma Continuous. International Journal of Production Research; 48: 1069–1086.
• 3. C-C Wang, K.-S. C.-H.-H. 2010. Application of 6-sigma Design System to Developing an Improvement Model for Multi-process Multi Characteristic. Vol. 225 Part B: J. Engineering Manufacture; 1205-1216.
• 4. Berger, A. 1997. Continuous improvement and kaizen: standardization and organizational designs. Integrated Manufacturing Systems; 110–117.
• 5. B. Modarress, A. A. 2005. Kaizen Costing for Lean Manufacturing: a Case Study. International Journal of Production Research; 43: 1751–1760.
• 6. K. Venkataramana, B. R. 2014. Application of Value Stream Mapping for Reduction of Cycle Time in a Machining Process. Procedia Materials Science; 6: 1187 – 1196.
• 7. Amit Kumar, A. a. 2013. Impacts of Kaizen in a Small-scale Industry of India: a Case Study. International Journal of Lean Six Sigma; 22-45.
• 8. Sunil Kumar, A. K. 2018. Process Improvement Through Lean-Kaizen Using Value Stream Map: A Case Study in India. The International Journal of Advanced Manufacturing Technology; 96: 2687–2698.
• 9. Aşkın Özdağoğlu, S. R. 2016. Applications of Kaizen and Cycle Time Reduction as Lean Production Techniques in a Semi-flexible PVC. Int. Journal of Management Economics and Business;12: 25-37.
• 10. ANSYS Topology Optimization. 2017. White paper, ANSYS Inc.,Canonsburg, PA U.S.A.; 1-4.
• 11. Dr.-Ing. Markus Stephan, D.-I. D.-P.-M. 2009. CFD Topology Optimization of Automotive Components. 4th European Automotive Simulation Conference EASC.
• 12. Chahande, R. Y. 1995. Automotive Applications of Topology Optimization. Structural Optimization; 9: 245-249.
• 13. Marco Cavazzuti, A. B. 2011. High performance automotive chassis design:. Struct Multidisc Optim; 44: 45–56.
• 14. Chao Li, I. Y. 2015. Conceptual and Detailed Design of an Automotive Engine Cradle by Using Topology, Shape, and Size Optimization. Structural and Multidisciplinary Optimization; 51: 547–564.
• 15. Hüseyin Güçlü YAVUZCAN, M. Ö. 2015. Yatık Ağız Açma Ve Kalibre Etme Makinasının Yapısal Analizi Ve Ağırlık Optimizasyonu. Gazi Üniversitesi Fen Bilimleri Dergisi; 3(3): 555-564.
• 16. R. Tavakoli, P. D. 2009. Optimal Riser Design in Sand Casting Process with Evolutionary Topology oOptimization. Struct Multidisc Optim; 205–214.
• 17. Vivien J. Challis, A. P.-C. 2010. Prototypes for Bone Implant Scaffolds Designed via Topology Optimization and Manufactured by Solid Freeform Fabrication. ADVANCED ENGINEERING MATERIALS; 12: 1105-1110.
• 18. Xiaojian Wang, S. X. 2016. Topological Design and Additive Manufacturing of Porous Metals for Bone Scaffolds and Orthopaedic Implants: A Review. Biomaterials; 83: 127-141.
• 19. Würth Industrie. Dimensioning metric screw assemblies. Wuerth Industrie:https://www.wuerth-industrie.com/web/media/en/pictures/wuerthindustrie/technikportal/dinokapitel/Kapitel_06_DINO_techn_Teil.pdf.
• 20. M. P. Bendsùe, O. S. 1999. Material Interpolation Schemes in Topology Optimization. Archive of Applied Mechanic; 69: 635-654.
• 21. Nişanci, M.C., Yurddaş, A. 2020. Compare Between the Results of the Casting Simulation and the Results of Experimental Production with Calculating the Interface Heat Transfer Coefficient of the Casting-Mold. Celal Bayar University Journal of Science; Volume 16, Issue 2, 2020, p 169-181 Doi: 10.18466/cbayarfbe.720791.