THE INVESTIGATION OF ABRASIVE WEAR OF Cu -C -Al2SiO5 COMPOSITE PRODUCED BY P/M PROCESS

Öz

In this study, the effect of C and aluminium silicate (Al2SiO5 ) on

abrasive wear of Cu-C -Al2SiO5 composite produced by powder metallurgy route,

containing 5, 10, 15 vol. % C and Al2SiO5 in Cu matrix was investigated. In the

experiments, wear resistance of samples were determined using different loads by

pin on disc wear apparatus. Microstructures of samples were examined by optical

and scanning electron microscopies,EDS and x-Ray diffraction methods. Finally, it

has been found that with the increasing C ve Al2SiO5 reinforcing particles and

loads, wear rate increased.

Anahtar Kelimeler

• Abrasive Wear,Copper Based Composite

T/M YÖNTEMİ İLE ÜRETİLEN Cu-C-Al2SiO5 KOMPOZİTİNİN ABRASİV AŞINMA DAYANIMI

Öz

Bu çalışmada, Cu tozuna hacimce %5, %10, %15 oranında C ve Al2SiO5 katılarak

toz metalurjisi yöntemi ile üretilen Cu-C-Al2SiO5 kompozitinin abrasiv aşınma

davranışı üzerinde karbon ve alüminyum silikat takviye partiküllerinin etkisi

araştırılmıştır. Aşınma deneyleri farklı yükler kullanılarak pim-disk aşınma

aparatında yapılmıştır. Numunelerin Mikroyapıları SEM, optik mikroskop, EDS ve

X-Ray ile incelenmiştir. Sonuç olarak bakır matrise katılan C ve Al2SiO5 takviye

partiküllerinin hacim oranının ve uygulama yükünün artmasıyla aşınma oranının

arttığı tespit edilmiştir.

Anahtar Kelimeler

• Abrasiv Aşınma,Bakır Esaslı Kompozit

Kaynakça

1. [1] S.C. Tjong and K.C.Lau, Tribological behaviour of SİC particle-reinforced copper matrix composites, Materials Letters 43, (1999), 274-280.
2. [2] M. Singh, M. Mondal, D.P. Modi, O.P. Jha, Two-body Abrasive Wear Behaviour of Aluminium Alloy-sillimanite Particle Reinforced Composite, Wear 253 (2002), 357-368.
3. [3] Metals Handbook, Ninth Edition, American Society for Metals, 1984, p. 7
4. [4] J. Kazior, C. Janczur, T.Pieczonka, J. Ploszczak, Thermochemical treatment of Fe-C-Mo alloys, Surface and Coatings Technology, 151-152(2002)333-337
5. [5] S.F. Moustafa, Z. Abdel- Hamid, A.M. Abd-elhay, Copper matrix SiC and Al2O3 Particulate composites by powder metallurgy technique, Materials Letters 53, (2002) 244-249.
6. [6] S.R. Dong, J.P. Tu, X.B. Zhang, An investigation of the sliding wear behavior of Cu-matrix composite reinforced by carbon nanotubes. Materials Science and Engineering A313 (2001) 83-87
7. [7] M. İzciler, M. Muratoglu, Wear behaviuor SiC reinforced 2124 Al alloy composite in RWAT system, Journal of Materials Processing Technology 132 (2002) 67-72.
8. [8] S.C. Tjong and K.C. Lau, Abrasive wear behavior of TBi2 particle –reinforced copper matrix composite Materials Science and Engineering A282 (2000)183-186.

9. [9] J.P. Tu, L. Meng, M.S. Liu, Friction and behavior of Cu- Fe3Al powder metallurgical composites in dry sliding, Wear 220(1998) 72-79,
10. [10] S.F. Moustafa, Z. Abdel-Hamid, A.M. Abd-Elhay, Friction and wear of copper-graphite composites made wiht Cu-coated and uncoated graphite powders, Wear 253(2001) 699-710
11. [11] A. Berner, K.C. Mundim, D.E. Ellis, Microstructure of Cu-C interface in Cu based metal matrix composite, Sensors and Actuators A: Physical, Volume 74, Issues 1-3 1999, 86-90.
12. [12] M.A. More, A review of two-body abrasive wear, Wear 27 (1974) 1-17.