Spiral Kaynaklı Çelik Boruların Korozyona Karşı FBE Kaplamaların Test Ve Karakterizasyonu

Yıl 2020, Cilt: 7 Sayı: 2, 679 - 689, 31.05.2020

Ekrem Altuncu , Gökhan Çil , Mahmut Gel

https://doi.org/10.31202/ecjse.690144

Öz

Doğalgaz boru hatlarında koruyucu kaplamalara olan gereksinim ve daha uzun ömür talebi sürekli artmaktadır. Kaplama-altlık arayüzey arası kirlikler, uygun olmayan yüzey hazırlama koşulları ve bunun yanında optimize edilmemiş kaplama proses parametreleri zorlu çalışma şartlarında kaplamanın kullanım ömrünü sınırlamaktadır. Bu makale çalışmasında farklı ortam koşullarında, toprak üstünde çalışan spiral kaynaklı çelik (X70M PSL2) doğalgaz borularının katodik korozyona karşı korunması amacıyla elektrostatik sprey tabancası ile uygulanan ergiterek bağlanan epoksi esaslı (FBE, fusion bonded epoxy) kaplamaların test sonuçları ve karakterizasyonu sunulmaktadır. Tek katmanlı FBE kaplamaların performansına etki eden birçok faktör arasında kaplama öncesi çelik ön yüzey hazırlıkları; kaplamanın performansını önemli ölçüde etkilemektedir. Yapılan deneysel çalışmalar, ilgili uluslararası test standartları ve şartnameler (CSA-Z245.20 seri 14) kapsamında kontrol edilmiş, kimyasal karakterizasyon yöntemleri (FTIR, SEM) ile analiz edilmiştir. Değerlendirme sonucunda FBE kaplamaların başarılı bir şekilde üretilebildiği ve farklı sıcaklık koşullarında katodik soyulma, yapışma testlerinden başarı ile geçtiği gözlemlenmiştir.

Anahtar Kelimeler

Çelik boru, Korozyon, Kaplama, Katodik Soyulma

Testing and Characterization of FBE Coatings Against Corrosion of Spiral Welded Steel Pipes

Öz

The need for protective coatings in natural gas pipelines and the demand for longer life is constantly increasing. Impurities between the coating and the substrate interface, unsuitable surface preparation conditions as well as unoptimized coating process parameters limit the service life of the coating under severe operating conditions. This article presents the test results and characterization of fused bonded epoxy based (FBE, fusion bonded epoxy) coatings applied with electrostatic spray gun to protect spiral welded steel (X70M PSL2) natural gas pipes working against soil under cathodic corrosion under different environmental conditions. Many factors affecting the performance of single-layer FBE coatings include pre-coating steel surface preparation; significantly affect the performance of the coating. Experimental studies were controlled in accordance with relevant international test standards and specifications (CSA-Z245.20 series 14) and analyzed by chemical characterization methods (FTIR, SEM). As a result of the evaluation, it has been observed that FBE coatings can be produced successfully and successfully passed cathodic peeling and adhesion tests under different temperature conditions.

Anahtar Kelimeler

Steel Pipe; corrosion; FBE coating; cathodic disbondment.

Kaynakça

• Kaynaklar
• [1] Saliba, P.A., Mansur, A.A., Santos, D.B., Mansur, S., “Fusion‑Bonded Epoxy Composite Coatings on Chemically Functionalized API Steel Surfaces for Potential Deep‑Water Petroleum Exploration”, Saliba et al. Appl Adhes Sci, 2015, pp 3-22.
• [2] Latino, M., Varela, F., Tan, Y., Forsyth, M., “The Effect of Ageing on Cathodic Protection Shielding by Fusion Bonded Epoxy Coatings”, Progress in Organic Coatings, 2019, Volume 134, pp.58-65.
• [3] Mobin, M., Malik, A.U., Andijani, I.N., Al-Muaili, F., Al-Hajri, M., Ozair, G., Mohammad N.M.K., “Performance Evaluation of Some Fusion-Bonded Epoxy Coatings under Water Transmission Line Conditions”, Progress in Organic Coatings, 2008, Volume 62, pp. 369-375.
• [4] Ramezanzadeh, B., Rostami, M., The Effect of Cerium-Based Conversion Treatment on the Cathodic Delamination and Corrosion Protection Performance of Carbon Steel-Fusion-Bonded Epoxy Coating Systems”, Applied Surface Science, 2017, Volume 392, pp. 1004-1016.
• [5] Jadoon, A.N.K., Thompson, I., “Fusion bonded epoxy mainline and field joint coatings performance from the X100 field trial e A case study” International Journal of Pressure Vessels and Piping, 2012, Volume 92, pp. 48-55.
• [6] CSA Z245.20 Series-14, “Plant-Applied External Fusion Bond Epoxy Coating for Steel Pipe”, 2014 Edition.
• [7] Aşkar, İ., “Petrol Ve Doğalgaz Borularının Tek Kat FBE Kaplanmasında Yüzey Profili Derinliklerinin Katodik Soyulma Performansına Etkileri”, Yüksek Lisans Tezi, İTÜ, 2009.
• [8] ISO 8501-1, “Preparation Of Steel Substrates Before Application Of Paints And Related Products - Visual Assessment Of Surface Cleanliness - Part 1: Rust Grades And Preparation Grades Of Uncoated Steel Substrates And Of Steel Substrates After Overall Removal Of Previous Coatings”, 2007 Edition.
• [9] ISO 8502-3, “Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method)”, 2017 Edition.
• [10] TES-CO-FBE-GL, “External Fusion Bond Epoxy for Steel Pipe Specification”, TransCanada Engineering, 2017 Edition.
• [11] Qian, S., Cheng, Y.F., “Degradation of fusion bonded epoxy pipeline coatings in the presence of direct current interference”, Progress in Organic Coatings, 2018, Volume 120, pp. 79-87.
• [12] Mahdavi, F., Tan, M.Y.J., Forsyth, M., “Electrochemical impedance spectroscopy as a tool to measure cathodic disbondment on coated steel surfaces: capabilities and limitations”, Progress in Organic Coatings, 2015, Volume 88, pp. 23-31.