Araştırma Makalesi

Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM

Cilt: 5 Sayı: 3 25 Ekim 2026
PDF İndir
EN TR

Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM

Öz

In this study, the mechanical performances of carbon fiber (CF) reinforced polylactic acid (PLA) composites produced using the multi-material FDM (Fused Deposition Modeling) method were investigated. Single-, two-, and three-layer configurations were fabricated using pure PLA, 5% carbon fiber-reinforced PLA (5CF), and 10% carbon fiber-reinforced PLA (10CF) filaments. Dimensional accuracy analyses showed that high geometric precision within ±0.1 mm was achieved for all specimens. The mechanical performance of the two-layer structures was higher compared to single-layer structures. The two-layer structure with a bottom layer of pure PLA and a top layer of 5% CF-PLA showed a 19% improvement in tensile strength, a 74% improvement in elastic modulus, and a 24% improvement in flexural strength (2T-5CF). The three-layer (PLA/5% CF/10% CF) hybrid structure provided a 65% increase in elastic modulus and a 4.2% increase in flexural strength compared to pure PLA (3T). However, the flexural strength of the 3T configuration (69.17 MPa) remained below that of the single-layer 5CF (78.08 MPa) and 10CF (70.71 MPa) specimens, indicating that the three-layer arrangement offers no flexural strength advantage over single-layer CF-reinforced structures despite its gradient character. The fracture surfaces were examined using scanning electron microscopy (SEM) to evaluate interlayer transition regions and possible separations. The results reveal that the interaction of layer alignment and fiber ratio plays a decisive role in shaping the mechanical performance in functionally graded (FGM) carbon fiber reinforced PLA composites produced by the multi-material FDM method.

Anahtar Kelimeler

Destekleyen Kurum

This study was supported by Karabük University Scientific Research Projects Coordination Unit (Project No: KBÜBAP-25-DS-054).

Proje Numarası

KBÜBAP-25-DS-054

Etik Beyan

The authors declare that there is no conflict of interest with any individual or institution regarding this study.

Teşekkür

The authors would like to thank Karabük University for providing laboratory facilities and technical support.

Kaynakça

  1. M. A. Caminero, J. M. Chacón, I. García-Moreno, and J. M. Reverte, “Interlaminar bonding performance of 3D printed continuous fibre reinforced thermoplastic composites using fused deposition modelling,” Polym. Test., vol. 68, pp. 415–423, Jul. 2018.
  2. A. Temiz, A. F. Yılmaz, F. H. Öztürk, F. Pehlivan, and M. M. Karaca, “Design and evaluation of hierarchical strut-based lattices with triply periodic minimal surface-inspired shells for bioinspired applications,” J. Mater. Eng. Perform., vol. 35, no. 13, pp. 12667–12681, Apr. 2026.
  3. S. Prajapati, J. K. Sharma, S. Kumar, S. Pandey, and M. K. Pandey, “A review on comparison of physical and mechanical properties of PLA, ABS, TPU, and PETG manufactured engineering components by using fused deposition modelling,” Mater. Today Proc., May 2024.
  4. B. Blake, R. Mendenhall, and B. Eslami, “Balancing strength and flexibility: Mechanical characterization of carbon fiber-reinforced PLA composites in FDM 3D printing,” J. Manuf. Mater. Process., vol. 9, no. 9, Art. no. 288, Sep. 2025.
  5. M. M. Karaca, İ. Ekinci, and D. Ali, “Effect of geometric modifications on the compressive strength and mechanical performance of gyroid-based bone scaffolds,” Int. J. 3D Print. Technol. Digit. Ind., vol. 9, no. 1, pp. 63–72, Apr. 2025.
  6. N. Maqsood and M. Rimašauskas, “Characterization of carbon fiber reinforced PLA composites manufactured by fused deposition modeling,” Compos. C Open Access, vol. 4, Art. no. 100112, Mar. 2021.
  7. A. Thirugnanasamabandam, M. Subramaniyan, B. Prabhu, and K. Ramachandran, “Development and comprehensive investigation on PLA/carbon fiber reinforced PLA based structurally alternate layered polymer composites,” J. Ind. Eng. Chem., vol. 136, pp. 248–257, Aug. 2024.
  8. Ö. Öz, F. H. Öztürk, and C. Güleç, “Effect of fiber content and plasticizer on mechanical and joint properties of carbon fiber powder reinforced PLA manufactured by 3D printing process,” J. Adhes. Sci. Technol., vol. 37, no. 15, pp. 2208–2231, Aug. 2023.

Ayrıntılar

Birincil Dil

İngilizce

Konular

Malzeme Tasarım ve Davranışları, Kompozit ve Hibrit Malzemeler

Bölüm

Araştırma Makalesi

Yayımlanma Tarihi

25 Ekim 2026

Gönderilme Tarihi

6 Nisan 2026

Kabul Tarihi

30 Haziran 2026

Yayımlandığı Sayı

Yıl 2026 Cilt: 5 Sayı: 3

Kaynak Göster

APA
Karaca, M. M., & Yildiz, T. (2026). Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM. Firat University Journal of Experimental and Computational Engineering, 5(3), 671-685. https://doi.org/10.62520/fujece.1924232
AMA
1.Karaca MM, Yildiz T. Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM. Firat University Journal of Experimental and Computational Engineering. 2026;5(3):671-685. doi:10.62520/fujece.1924232
Chicago
Karaca, Muhammet Mevlüt, ve Tuğçe Yildiz. 2026. “Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM”. Firat University Journal of Experimental and Computational Engineering 5 (3): 671-85. https://doi.org/10.62520/fujece.1924232.
EndNote
Karaca MM, Yildiz T (25 Ekim 2026) Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM. Firat University Journal of Experimental and Computational Engineering 5 3 671–685.
IEEE
[1]M. M. Karaca ve T. Yildiz, “Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM”, Firat University Journal of Experimental and Computational Engineering, c. 5, sy 3, ss. 671–685, Eki. 2026, doi: 10.62520/fujece.1924232.
ISNAD
Karaca, Muhammet Mevlüt - Yildiz, Tuğçe. “Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM”. Firat University Journal of Experimental and Computational Engineering 5/3 (25 Ekim 2026): 671-685. https://doi.org/10.62520/fujece.1924232.
JAMA
1.Karaca MM, Yildiz T. Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM. Firat University Journal of Experimental and Computational Engineering. 2026;5:671–685.
MLA
Karaca, Muhammet Mevlüt, ve Tuğçe Yildiz. “Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM”. Firat University Journal of Experimental and Computational Engineering, c. 5, sy 3, Ekim 2026, ss. 671-85, doi:10.62520/fujece.1924232.
Vancouver
1.Muhammet Mevlüt Karaca, Tuğçe Yildiz. Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM. Firat University Journal of Experimental and Computational Engineering. 25 Ekim 2026;5(3):671-85. doi:10.62520/fujece.1924232