Lokal Kütle Konumunun Ses İletim Performansına Etkisinin İncelenmesi

Öz

Bu çalışma, hafif polimer esaslı yapılarda lokal (yerel) kütle dağılımının vibro-akustik performans üzerindeki belirleyici rolünü, 3 mm kalınlığındaki daire biçimli bir PLA plaka üzerinden sistematik olarak incelemektedir. Geleneksel hoparlörlere seçenek olarak gelişen ses uyarıcılarının (exciter) verimliliğini artırmayı hedefleyen araştırmada, asimetrik modların uyarılması amacıyla eksantrik (merkez dışı) bir bağlantı yapısı tercih edilmiştir. 0–5000 Hz frekans bandında gerçekleştirilen ardışık modal, harmonik yapısal ve harmonik akustik analizler, plaka üzerindeki 200 gramlık lokal kütlenin 8 farklı konumdaki etkisini ortaya koymaktadır. Elde edilen veriler, kütle yerleşiminin sadece titreşim genliğini değil, aynı zamanda akustik ses iletim verimini de doğrudan yönettiğini kanıtlamaktadır. Analiz sonuçlarına göre, lokal kütlenin stratejik konumlandırılmasıyla ses basınç seviyesinde (SPL– Sound Pressure Level) belirli frekans bantlarında hedeflenen artışların veya mod baskılanması yoluyla azalışların sağlanabildiği görülmüştür. Örneğin, kütle konumu değişiminin SPL bazında ise yaklaşık 8 dB’lik bir varyasyona neden olduğu tespit edilmiştir. Bu araştırma, lokal kütle yerleşiminin rastgele bir yapısal yükten ziyade, vibro-akustik performansı optimize eden stratejik bir tasarım değişkeni olarak kullanılabileceğini literatüre sunmaktadır. 

Anahtar Kelimeler

• Ses basınç seviyesi
• Lokal kütle etkisi
• akustik performans
• titreşim ve akustik

Experimental Investigation of Sound Transmission Performance of Plates Made from Different Materials

Öz

This study systematically investigates the decisive role of local mass distribution on the vibro-acoustic performance of lightweight polymer-based structures, using a 3 mm thick circular PLA plate. Aiming to enhance the efficiency of sound exciters emerging as an alternative to traditional loudspeakers, an eccentric (off-center) attachment configuration was preferred to stimulate asymmetric modes. Sequential modal, harmonic structural, and harmonic acoustic analyses conducted within the 0–5000 Hz frequency range reveal the impact of a 200-gram local mass at eight different positions on the plate. The obtained data proves that mass placement directly governs not only the vibration amplitude but also the acoustic sound transmission efficiency. According to the analysis results, it was observed that targeted increases in sound pressure level (SPL) in specific frequency bands, or reductions through mode suppression, can be achieved by strategically positioning the local mass. For instance, it was determined that the change in mass position caused a variation of approximately 8 dB in terms  of SPL. This research presents to the literature that local mass placement can be utilized as a strategic design variable that optimizes vibro-acoustic performance, rather than being a random structural load.
 

Anahtar Kelimeler

• Sound pressure level (SPL)
• Local mass effect
• Acoustic performance
• Vibration and acoustics
• Vibro-acoustic analysis

Kaynakça

1. Tian, R., Xu, Y., Duan, F., & Wang, J. J. (2023). The deformation and dynamics of a flexible plate with attached mass blocks mounted behind a circular cylinder. Journal of Fluids and Structures, 122, 103979. https://doi.org/10.1016/j.jfluidstructs.2023.103979
2. Chen, W., Hao, Y. X., Zhang, W., Yang, S. W., & Cao, Y. T. (2024). Vibration isolation performance of a novel metamaterials sandwich cylindrical panel by locally resonant band gap. Journal of Vibration Engineering & Technologies, 12(4), 6121–6136. https://doi.org/ 10.1007/s42417-023-01242-7
3. Liu, X., Zhou, Y., & Wang, J. (2023). Highly accurate wavelet solution for bending and free vibration of circular plates over extra-wide ranges of deflections. Journal of Applied Mechanics, 90(3), Article 031009. https://doi.org/10.1115/1.4056397
4. Parida, S. P., Jena, P. C., Das, S. R., Basem, A., Khatua, A. K., & Elsheikh, A. H. (2024). Transverse vibration of laminated-composite-plates with fillers under moving mass rested on elastic foundation using higher order shear deformation theory. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 238(20), 9878–9888. https://doi.org/ 10.1177/09544062241256589
5. Ramachandran, B., Raveendran, R., & Mondal, A. (2025). Horn sound digital validation for ECE-R28 regulation compliance (SAE Technical Paper No. 2025-01-0008). SAE International. https://doi.org/10.4271/2025-01-0008
6. Schneider, A. J. (1974). Relating acoustical measurements to SAE procedures (SAE Technical Paper No. 740212). SAE International. https://doi.org/10.4271/740212
7. Kopmaz, O., & Telli, S. (2002). Free vibrations of a rectangular plate carrying a distributed mass. Journal of Sound and Vibration, 251(1), 39–57. https://doi.org/ 10.1006/jsvi.2001.3977
8. Yildiz, A., & Kopmaz, O. (2017). Experimental and computational validation of an analytical model of free vibration of a rectangular plate carrying a distributed mass. International Journal of Advances in Engineering and Technology, 10(2), 233–244.

9. Gurukiran, K., & Samal, P. K. (2021, October). Experimental determination of mode shapes of a plate using speaker as excitation device. In IOP Conference Series: Materials Science and Engineering (Vol. 1189, No. 1, p. 012029). IOP Publishing. https://doi.org/10.1088/1757-899X/1189/1/012029
10. Olive, S. E. (2004). A multiple regression model for predicting loudspeaker preference using objective measurements: Part II—Development of the model. Audio Engineering Society Convention 117, Northridge, CA, USA.
11. McMillan, J., & Keane, A. J. (1996). Shifting resonances from a frequency band by applying concentrated masses to a thin rectangular plate. Journal of Sound and Vibration, 192(2), 549–562. https://doi.org/10.1006/jsvi.1996.0202
12. Zenker, B., Rawoof, S. S. A., Merchel, S., & Altinsoy, M. E. (2019). Low deviation and high sensitivity—Optimized exciter positioning for flat panel loudspeakers by considering averaged sound pressure equalization. Audio Engineering Society Convention 147, Dresden, Germany.
13. Zenker, B., Heinl, M., Merchel, S., & Altinsoy, M. E. (2020). Low frequency performance of a woofer-driven flat panel loudspeaker (Part 2: Numerical system optimization and large signal analysis). Audio Engineering Society Convention 149, Dresden, Germany.
14. Jung, J., Kook, J., Goo, S., & Wang, S. (2017). Sound transmission analysis of plate structures using the finite element method and elementary radiator approach with radiator error index. Advances in Engineering Software, 112, 1–15. https://doi.org/10.1016/j.advengsoft.2017.06.012
15. Du, J., & Olhoff, N. (2007). Topological design of freely vibrating continuum structures for maximum values of simple and multiple eigenfrequencies and frequency gaps. Structural and Multidisciplinary Optimization, 34(2), 91–110. https://doi.org/ 10.1007/s00158-007-0101-y
16. Ma, X., Zhang, J., & Yan, S. (2012). Experimental modal analysis and modal reproduce experiment research of a Chladni plate. Applied Mechanics and Materials, 152-154, 1401–1405. https://doi.org/10.4028/www.scientific.net/AMM.152-154.1401
17. Ikpe, A. E., Ndon, A. E., & Etuk, E. M. (2019). Response variation of Chladni patterns on vibrating elastic plate under electro-mechanical oscillation. Nigerian Journal of Technology, 38(3), 540–548. http://dx.doi.org/10.4314/njt.v38i3.2
18. Tuan, P. H., Wen, C. P., Chiang, P. Y., & Yu, Y. T. (2015). Exploring the resonant vibration of thin plates: Reconstruction of Chladni patterns and determination of resonant wave numbers. The Journal of the Acoustical Society of America, 137(4), 2113–2123. https://doi.org/ 10.1121/1.4916704
19. Escaler, X., & De La Torre, O. (2018). Axisymmetric vibrations of a circular Chladni plate in air and fully submerged in water. Journal of Fluids and Structures, 82, 432-445. https://doi.org/ 10.1016/j.jfluidstructs.2018.07.017
20. Pandit, M. K., Haldar, S., & Mukhopadhyay, M. (2007). Free vibration analysis of laminated composite rectangular plate using finite element method. Journal of Reinforced Plastics and Composites, 26(1), 69–80. https://doi.org/ 10.1177/0731684407069955
21. Wang, T., Guo, H., Chen, M., & Dong, W. (2022). Theoretical modeling and analysis of vibroacoustic characteristics of an acoustic metamaterial plate. Acta Mechanica Solida Sinica, 35(5), 775–786. https://doi.org/ 10.1007/s10338-022-00320-9
22. Hao, W. F., & Kam, T. Y. (2009). Modal characteristics of symmetrically laminated composite plates flexibly restrained at different locations. International Journal of Mechanical Sciences, 51(6), 443–452. https://doi.org/10.1016/j.ijmecsci.2009.04.002
23. Zhang, X., & Li, W. L. (2010). A unified approach for predicting sound radiation from baffled rectangular plates with arbitrary boundary conditions. Journal of Sound and Vibration, 329(25), 5307–5320. https://doi.org/ 10.1016/j.jsv.2010.07.014
24. Xu, Z., Huang, Q., & Zhao, Z. (2011). Topology optimization of composite material plate with respect to sound radiation. Engineering Analysis with Boundary Elements, 35(1), 61–67. https://doi.org/10.1016/j.enganabound.2010.05.011
25. Jiang, C., Kam, T., & Chang, Y. (2017). Sound radiation of panel-form loudspeaker using flat voice coil for excitation. Applied Acoustics, 116, 375–389. https://doi.org/ 10.1016/j.apacoust.2016.10.009
26. Bablu, M. A., Akinmolayan, O. P., & Manimala, J. M. (2022). Sound transmission loss of meta-acoustic barriers with anomalous effective-mass. Journal of Theoretical and Computational Acoustics, 22(1), 2250014. https://doi.org/ 10.1142/S2591728522500141
27. Currey, M. N., & Cunefare, K. A. (1995). The radiation modes of baffled finite plates. The Journal of the Acoustical Society of America, 98(3), 1570–1580. https://doi.org/ 10.1121/1.413423
28. Snyder, S. D., & Tanaka, N. (1995). Calculating total acoustic power output using modal radiation efficiencies. The Journal of the Acoustical Society of America, 97(3), 1702–1709. https://doi.org/10.1121/1.412048
29. Hu, H. X., Tang, B., & Zhao, Y. (2016). Active control of structures and sound radiation modes and its application in vehicles. Journal of Low Frequency Noise, Vibration and Active Control, 35(4), 291–302. https://doi.org/10.1177/0263092316676400
30. Yamaguchi, Z., Bolton, J. S., & Sakagami, K. (2011). Reduction of sound radiation by using force radiation modes. Applied Acoustics, 72(7), 420–427. https://doi.org/ 10.1016/j.apacoust.2011.01.006
31. Pasqual, M., Arruda, J. R., & Herzog, P. (2010). Application of acoustic radiation modes in the directivity control by a spherical loudspeaker array. Acta Acustica united with Acustica, 96(1), 32–42. https://doi.org/10.3813/AAA.918253
32. Boay, C. G. (1993). Free vibration of rectangular isotropic plates with and without a concentrated mass. Computers & structures, 48(3), 529-533. https://doi.org/ 10.1016/0045-7949(93)90331-7
33. Jiang, C. H., & Kam, T. Y. (2013). Vibration analysis of elastically restrained laminated composite sound radiation plates via a finite element approach. Procedia Engineering, 67, 545–558. https://doi.org/10.1016/j.proeng.2013.12.054
34. Li, H., Tang, Z., Zuo, G., & Ma, F. (2024). Laminated acoustic metamaterials for low-frequency broadband ultra-strong sound insulation. Thin-Walled Structures, 202, 112151. https://doi.org/10.1016/j.tws.2024.112151
35. Duval, A., Crignon, G., Goret, M., & Ponsinet, D. (Yıl Belirtilmemiş). Immersive smart trims design using linear inertial transducers for a better audio sound quality and easier vehicle integration.].
36. Sun, Y., Dong, J., Lee, H. P., & Zheng, H. (2024). Sound transmission characteristics of X-shape inertial amplification acoustic metamaterial. Applied Acoustics, 218, 109908. https://doi.org/10.1016/j.apacoust.2024.109908
37. United Nations Economic Commission for Europe. "UN Regulation No. 28: Uniform provisions concerning the approval of audible warning devices and of motor vehicles with regard to their audible signals," Rev.2, Amend.5, United Nations, 2018.