METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI

Yusuf Ayan; Nizamettin Kahraman

METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI

Öz

İsteğe özel, karmaşık şekilli ve geleneksel yöntemlerle üretimi zor olan parçaların üretimi eklemeli imalat (Eİ) yöntemleriyle mümkündür. Eİ yöntemi günümüzde birçok sektörün uygulama alanına girmiş önemli ve geliştirilmeye açık bir çalışma konusu durumuna gelmiştir. Bu yöntemle çoğunlukla polimer malzemelerin üretilmesinin yanı sıra metal ve seramiklerinde üretimi sağlanabilmektedir. Metallerin Eİ işlemlerinde farklı birçok yöntem geliştirilmiştir. Tel ark eklemeli imalat (TAEİ) işlemi bu yöntemlerden birisidir. Kaynak işlemi esasına dayanan bu yöntemle farklı kaynak prensipleriyle üretim gerçekleştirilebilmekte, yüksek miktarlarda malzeme biriktirilerek büyük metal parçalar üretilebilmektedir. Sunulan bu çalışmada TAEİ yönteminin tanıtılarak, avantajlarına değinilmiş ve bazı uygulamaları gösterilmiştir. Konuyla ilgili önceden yapılan çalışmaların bir kısmı değerlendirilerek, yöntemin uygulandığı malzemeler ve üretim yaklaşımları gibi konulara değinilmiştir.

Anahtar Kelimeler

eklemeli imalat

Kaynakça

1. Hascoët, J. Y., Parrot, J., Mognol, P. and Willmann, E., “Induction Heating in a Wire Additive Manufacturing Approach”, Welding in the World, Vol. 62, Pages 249-257, 2018.
2. Guo, J., Zhou, Y., Liu, C., Wu, Q., Chen, S. and Lu, J., “Wire Arc Additive Manufacturing of AZ31 Magnesium Alloy: Grain Refinement by Adjusting Pulse Frequency”, Materials, Vol.9, Issue 10, 823, 2016.
3. Hu, Z., Qin, X., Shao, T. and Liu, H., “Understanding and Overcoming of Abnormity at Start and End of the Weld Bead in Additive Manufacturing with GMAW”, The International Journal of Advanced Manufacturing Technology, Vol. 95, Pages 2357-2368, 2018.
4. Somashekara, M. A. and Suryakumar, S., “Studies on Dissimilar Twin-Wire Weld-Deposition for Additive Manufacturing Applications”, Trans Indian Inst. Met., Vol. 70, Issue 8, Pages 2123-2135, 2017.
5. Ding, D., Pan, Z. S., Cuiuri, D. and Li, H., “A tool-path generation strategy for wire and arc additive manufacturing” , Int J Adv Manuf Technol , Vol. 73, Pages 173-183, 2014.
6. Turhan, S. ve Özsoy, A., “Dmls Yöntemiyle İmal Edilen Ti6al4v Alaşım Özelliklerine İşlem Parametrelerinin Etkisi”, SDU International Journal of Technological Science, Cilt 8, Sayı 2, Sayfa 15-27, 2016.
7. Bermingham, M. J., Nicastro, L., Kent, D., Chen, Y. and Dargusch, M. S., “Optimising the mechanical properties of Ti-6Al-4V components produced by wire + arc additive manufacturing with post-process heat treatments”, Journal of Alloys and Compounds, Vol. 753, Pages 247-255, 2018.
8. Fuchs, J., Schneider, C. and Enzinger, N., “Wire-Based Additive Manufacturing Using An Electron Beam As Heat Source”, Welding in the World, Vol. 62, Pages 267-275, 2018.

9. Ge, J., Lin, J., Chen, Y., Lei, Y. and Fu, H., “Characterization of wire arc additive manufacturing 2Cr13 part: Process stability, microstructural evolution, and tensile properties”, Journal Alloys and Compounds, Vol. 748, Pages 911-921, 2018.
10. İnternet: “Choosing Between 3D Printing & CNC Machining”, https://www.core77.com/posts/71171/Choosing-Between-3D-Printing-n-CNC-Machining, November 16, 2018.
11. Li, F., Chen, S., Shi, J., Tian, H. and Zhao, Y., “Evaluation and Optimization of a Hybrid Manufacturing Process Combining Wire Arc Additive Manufacturing with Milling for the Fabrication of Stiffened Panels”, Applied Sciences, Vol. 7, 1233, 2017.
12. Posch, G., Chladil, K. and Chladil, H., “Material Properties of CMT—Metal Additive Manufactured Duplex Stainless Steel Blade-Like Geometries”, Weld World, Vol. 61, Pages 873-882, 2017.
13. Hoefer, K., Haelsig, A. and Mayr, P., “Arc-based additive manufacturing of steel components—comparison of wire- and powder-based variants”, Welding in the World, Vol. 62, Pages 243-247, 2018.
14. Li, F., Chen, S., Wu., Z. and Yan, Z., “Adaptive process control of wire and arc additive manufacturing for fabricating complex-shaped components”, The International Journal of Advanced Manufacturing Technology, Vol. 69, Pages 871-879, 2018.
15. Liberini, M., Astarita, A., Campatelli, G., Scippa, A., Montevecchi, F., Venturini, G., Durante, M., Boccarusso, L., Memola, F., Minutolo, C. and Squillace, A., “Selection of Optimal Process Parameters for Wire Arc Additive Manufacturing”, 10th CIRP Conference on Intelligent Computation in Manufacturing Engineering - CIRP ICME '16, Vol. 62, Pages470-474, 2017.
16. Sun, R., Li, L., Zhu, Y., Guo, W., Peng, P., Cong, B., Sun, J., Che Z., Li, B., Guo, C. and Liu, L., “Microstructure, residual stress and tensile properties control of wire-arc additive manufactured 2319 aluminum alloy with laser shock peening”, Journal of Alloys and Compounds, Vol. 747, Pages 255-265, 2018.
17. Fang, X., Zhang, L., Li, H., Li, C., Huang, K. and Lu, B., “Microstructure Evolution and Mechanical Behavior of 2219 Aluminum Alloys Additively Fabricated by the Cold Metal Transfer Process”, Materials, Vol. 11, 812, 2018.
18. Ge., J, Lin, J., Lei, Y. and Fu, H., “Location-related thermal history, microstructure, and mechanical properties of arc additively manufactured 2Cr13 steel using cold metal transfer welding”, Materials Science & Engineering A, Vol. 715, Pages 144-153, 2018.
19. Martina, F., İnternet: “Wire + Arc Additive Manufacturing: properties, cost, parts”, https://www.researchgate.net/profile/Filomeno_Martina/publication/278017889_Wire_Arc_Additive_Manufacturing_properties_cost_parts/links/557866a308aeacff200282e0/Wire-Arc-Additive-Manufacturing-properties-cost-parts, February 25, 2018.
20. Dong, B., Pan, Z., Shen, C, Ma, Y. and Li, H., “Fabrication of Copper-Rich Cu-Al Alloy Using the Wire-Arc Additive Manufacturing Process”, Metallurgical and Materials Transactions B, Vol. 48B, Pages 3143-3151, 2017.
21. Yili, D., Shengfu, Y., Yusheng, S., Tianying, H. and Lichao, Z., “Wire and arc additive manufacture of high-building multi-directional pipe joint”, The International Journal of Advanced Manufacturing Technology, Vol. 96, Pages 2389-2396, 2018.
22. Gordon, J. V., Haden C. V., Nied, H. F., Vinci, R. P. and Harlow, D. G., “Fatigue crack growth anisotropy, texture and residual stress in austenitic steel made by wire and arc additive manufacturing”, Materials Science & Engineering A, Vol. 724, Pages 431-438, 2018.
23. Williams, S. W., Martina, F., Addison, A. C., Ding, J., Pardal, G. and Colegrove, P., “Wire+arc additive manufacturing”, Materials Science and Technology, Vol. 32, Issue 7, Pages 641-647, 2016.
24. Abe, T. and Sasahara, H., “Dissimilar Metal Deposition with a Stainless Steel and Nickel-Based Alloy Using Wire and Arc-Based Additive Manufacturing”, Precision Engineering, Vol. 45, Pages 387-395, 2016.
25. Queguineur, A., Rückert, G., Cortial, F. and Hascoët, J. Y., “Evaluation of wire arc additive manufacturing for large-sized components in naval applications”, Welding in the World, Vol. 62, Pages 259-266, 2018.
26. Xie, Y., Gao, M., Wang, F., Zhang, C., Hao, K., Wang, H. and Zeng, Z., “Anisotropy of fatigue crack growth in wire arc additive manufactured Ti-6Al-4V”, Materials Science & Engineering A, Vol. 709, Pages 265-269, 2018.
27. Wang, F., Williams S. and Rush, M., “Morphology investigation on direct current pulsed gas tungsten arc welded additive layer manufactured Ti6Al4V alloy”, Int. J. Adv. Manuf. Technol., Vol. 57, Pages 597-603, 2011.
28. Zhang, C., Li, Y., Gao, M. and Zeng, X., “Wire Arc Additive Manufacturing Of Al-6Mg Alloy Using Variable Polarity Cold Metal Transfer Arc As Power Source”, Materials Science & Engineering A, Vol. 711, Pages 415-423, 2018.
29. İnternet: “An Introduction to Wire Arc Additive Manufacturing”, https://amfg.ai/2018/05/17/an-introduction-to-wire-arc-additive-manufacturing/, November 16, 2018.
30. Shi, X., Ma, S., Liu, C., Wu, Q., Lu, J., Liu, Y. and Shi, W., “Selective Laser Melting-Wire Arc Additive Manufacturing Hybrid Fabrication of Ti-6Al-4V Alloy”, Materials Science & Engineering A, Vol. 684, Pages 196-204, 2017.
31. Wang, F., Williams, S., Colegrove, P. and Antonysamy, A. A., “Microstructure and Mechanical Properties of Wire and Arc Additive Manufactured Ti-6Al-4V”, Metallurgical And Materials Transactions A, Vol. 44A, Pages 968-977, 2013.
32. Bai, J., Ding, H. L., Gu, J. L., Wang, X. S. and Qiu, H., “Porosity Evolution in Additively Manufactured Aluminium Alloy During High Temperature Exposure”, IOP Conference Series: Materials Science and Engineering, Vol. 167, 0120145, 2017.
33. Horgar, A., Fostervoll, H., Nyhus, B., Ren, X., Eriksson, M. and Akselsen, O. M., “Additive Manufacturing Using WAAM with AA5183 Wire”, Journal of Materials Processing Tech., Vol. 259, Pages 68-74, 2018.
34. Ji, L., Lu, J., Liu, C., Jing, C., Fan, H. and Ma, S., “Microstructure and mechanical properties of 304L steel fabricated by arc additive manufacturing”, MATEC Web of Conferences, Vol. 128, 03006, 2017.
35. Chen, X., Li, J., Cheng, X., He, B., Wang, H. and Huang, Z., “Microstructure and Mechanical Properties of the Austenitic Stainless Steel 316L Fabricated by Gas Metal Arc Additive Manufacturing”, Materials Science & Engineering A, Vol. 703, Pages 567-577, 2017.
36. Ding, D., Pan, Z., van Duin, S., Li, H. and Shen, C. , “Fabricating Superior NiAl Bronze Components through Wire Arc Additive Manufacturing”, Materials, Vol. 9, 652, 2016.
37. Wu, B., Ding, D., Pan, Z., Cuiuri, D., Li, H., Han, J. and Fei, Z., “Effects of heat accumulation on the arc characteristics and metal transfer behavior in Wire Arc Additive Manufacturing of Ti6Al4V”, Journal of Materials Processing Tech., Vol. 250, Pages 304-312, 2017.
38. Wu., Q., Lu, J., Liu, C., Shi, X., Ma, Q., Tang, S, Fan, H. and Ma, S, “Obtaining uniform deposition with variable wire feeding direction during wire-feed additive manufacturing”, Materials and Manufacturing Processes, Vol. 32, Issue 16, Pages 1881-1886, 2017.
39. Cong, B., Ding, J. and Williams, S., “Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3%Cu alloy”, Int. J. Adv. Manuf. Technol., Vol. 76, Pages 1593-1606, 2015.
40. Yang, J., Yang, H., Yu, H., Wang, Z. and Zeng, X., “Corrosion Behavior of Additive Manufactured Ti-6Al-4V Alloy in NaCl Solution”, Metallurgical and Materials Transactions A, Vol. 48A, Pages 3583-3593, 2017.
41. Fu, Y., Zhang, H., Wang, G. and Wang, H., “Investigation of mechanical properties for hybrid deposition and micro-rolling of bainite steel”, Journal of Materials Processing Tech., Vol. 250, Pages 220-227, 2017.
42. Qi, Z., Cong, B., Qi, B., Sun, H., Zhao, G. and Ding, J., “Microstructure and mechanical properties of double-wire +arc additively manufactured Al-Cu-Mg alloys”, Journal of Materials Processing Tech., Vol. 255, Pages 347-353, 2018.
43. Shen, C., Pan, Z., Cuiuri, D., Roberts, J. and Li, H., “Fabrication of Fe-FeAl Functionally Graded Material Using the Wire-Arc Additive Manufacturing Process”, Metallurgical and Materials Transactions B, Vol. 47B, Pages 763-772, 2016.
44. Ma, Y., Cuiuri, D., Hoye, N., Li, H. and Pan., Z., "The effect of location on the microstructure and mechanical properties of titanium aluminides produced by additive layer manufacturing using in-situ alloying and gas tungsten arc welding", Materials Science & Engineering A, Vol. 631, Pages 230-240, 2015.
45. Geng, H., Li, J., Xiong, J., Lin, X., Huang, D., and Zhang, F., “Formation and improvement of surface waviness for additive manufacturing 5A06 aluminium alloy component with GTAW system”, Rapid Prototyping Journal, Vol. 24, Issue 2, Pages 342-350, 2018.
46. Lockett, H., Ding, J., Williams, S. and Martina, F., “Design for Wire + Arc Additive Manufacture: design rules and build orientation selection”, Journal of Engineering Design, Vol. 28, Issue 7-9, Pages 568-598, 2017.

Ayrıntılar

Birincil Dil

Türkçe

Konular

Mühendislik

Bölüm

Derleme

Yazarlar

Yusuf Ayan ^*
Türkiye

Nizamettin Kahraman

Yayımlanma Tarihi

30 Aralık 2018

Gönderilme Tarihi

4 Aralık 2018

Kabul Tarihi

27 Aralık 2018

Yayımlandığı Sayı

Yıl 2018 Cilt: 2 Sayı: 3

IZ

https://izlik.org/JA45JN92CS

Kaynak Göster

RIS / Bibtex

APA

Ayan, Y., & Kahraman, N. (2018). METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI. International Journal of 3D Printing Technologies and Digital Industry, 2(3), 74-84. https://izlik.org/JA45JN92CS

AMA

1.Ayan Y, Kahraman N. METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI. IJ3DPTDI. 2018;2(3):74-84. https://izlik.org/JA45JN92CS

Chicago

Ayan, Yusuf, ve Nizamettin Kahraman. 2018. “METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI”. International Journal of 3D Printing Technologies and Digital Industry 2 (3): 74-84. https://izlik.org/JA45JN92CS.

EndNote

Ayan Y, Kahraman N (01 Aralık 2018) METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI. International Journal of 3D Printing Technologies and Digital Industry 2 3 74–84.

IEEE

[1]Y. Ayan ve N. Kahraman, “METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI”, IJ3DPTDI, c. 2, sy 3, ss. 74–84, Ara. 2018, [çevrimiçi]. Erişim adresi: https://izlik.org/JA45JN92CS

ISNAD

Ayan, Yusuf - Kahraman, Nizamettin. “METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI”. International Journal of 3D Printing Technologies and Digital Industry 2/3 (01 Aralık 2018): 74-84. https://izlik.org/JA45JN92CS.

JAMA

1.Ayan Y, Kahraman N. METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI. IJ3DPTDI. 2018;2:74–84.

MLA

Ayan, Yusuf, ve Nizamettin Kahraman. “METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI”. International Journal of 3D Printing Technologies and Digital Industry, c. 2, sy 3, Aralık 2018, ss. 74-84, https://izlik.org/JA45JN92CS.

Vancouver

1.Yusuf Ayan, Nizamettin Kahraman. METAL EKLEMELİ İMALAT: TEL ARK YÖNTEMİ VE UYGULAMALARI. IJ3DPTDI [Internet]. 01 Aralık 2018;2(3):74-8. Erişim adresi: https://izlik.org/JA45JN92CS