MODELING OF TENSILE AND BENDING STRENGTH FOR PLA PARTS PRODUCED BY FDM

Öz

Fused deposition modeling (FDM) is one of the commonly used additive manufacturing methods to produce quality products with low cost complex geometries with efficient manufacturing and delivery logistics. Mechanical properties can be improved by examining numerous FDM parameters and/or using new materials through this method. In this study, mathematical models have been developed for estimation of some mechanical properties of parts produced by using PLA+ plastic material by FDM method. For this purpose, standard tensile and bending test samples were produced with 3D printer at three different printing speeds and filling ratio with two different raster angles. The effects of process parameters on tensile and bending strength were analyzed experimentally and statistically. According to the experimental results, the importance order of the parameters for mechanical properties of PLA+ based samples were determined as filling ratio, raster angle and printing speed. Tensile and bending strengths were higher in samples produced at 0/90° raster angle. On the other hand, it was determined that the increase in the printing speed decreased the tensile and bending strength proportionally. Between the results obtained from the mathematical models developed with multiple regression analysis and experimental results, an average deviation of 3% for tensile strength and 2% for bending strength were found.

Anahtar Kelimeler

• FDM,Tensile strength,Bending strength,PLA,Modelling

Kaynakça

1. 1. Dizon, J.R.C., Espera, A.H., Chen, Q., Advincula, R.C., “Mechanical characterization of 3d-printed polymers”, Additive Manufacturing, Vol 20, Pages 44–67, 2018.
2. 2. Lee, J.Y., An, J., Chua, C.K., “Fundamentals and applications of 3D printing for novel materials”, Applied Materials Today, Vol 7, Pages 120–133, 2017.
3. 3. Mohamed, O.A., Masood, S.H., Jahar L.B., "Optimization of fused deposition modeling process parameters: a review of current research and future prospects", Advances in Manufacturing, Vol 3, Pages 42-53, 2015.
4. 4. Turner, B.N., Strong, R., Gold, S.A., “A Review of melt extrusion additive manufacturing processes: I. process design and modeling”, Rapid Prototyping Journal, Vol 20, Issue 3, Pages 192-204, 2014.
5. 5. Casavola, C., Cazzato, A., Moramarco, V., Pappalettere, C. “Orthotropic mechanical properties of fused deposition modelling parts described by classical laminate theory”, Material and Design, Vol 90, Pages 453–458, 2016.
6. 6. Rankouhi, B., Javadpour, S., Delfanian, F., Letcher, T., “Failure analysis and mechanical characterization of 3d printed abs respect to later thickness and orientation”, J. Fail. Anal. Prev., Vol 16, Pages 467–481, 2016.
7. 7. Domingo, M., Puigriol, J.M., Garcia, A.A., Lluma, J., Borros, S., Reyes, G., “Mechanical property characterization and simulation of fused deposition modeling polycarbonate parts”, Material and Design, Vol 83, Pages 670–677, 2015.
8. 8. Sood, A.K., Ohdar, R.K., Mahapatra, S.S., “Parametric appraisal of mechanical property of fused deposition modelling processed parts”, Material and Design, Vol 31, Pages 287–295, 2010.9. Arivazhagan, A., Masood, S.H., “Dynamic mechanical properties of ABS material processed by fused deposition modelling. Int J Eng Res Appl., Vol 2(3), Pages 2009–2014, 2012.

9. 10. Evlen, H., Erel, G., Yılmaz, E., “Açık ve kapalı sistemlerde doluluk oranının parça mukavemetine etkisinin incelenmesi”, Politeknik Dergisi, Cilt 21, Sayı 3, Sayfa 651-662, 2018.
10. 11. Popescu, D., Zapciu, A., Amza, C., Baciu, F., Marinescu, R., “FDM process parameters influence over the mechanical properties of polymer specimens: a review”, Polymer Testing, Vol 69, Pages 157– 166, 2018.
11. 12. Vaezi, M., Chua, C.K., “Effects of layer thickness and binder saturation level parameters on 3D printing process”, Int. J. Adv. Manuf. Technol., Vol 53, Pages 275–284, 2011.
12. 13. ESUN, http://www.esun3d.net/products/142.html (2018.02.02), 2018.
13. 14. Günay, M., Gündüz, S., Yılmaz, H., Yaşar, N., Kaçar, R., “Optimization of 3D printing operation parameters for tensile strength in PLA based sample”, Journal of Polytechnic, 2019.
14. 15. Ahn, S. H., Montero, M., Odell, D., Roundy, S., Wright, P. K., “Anisotropic material properties of fused deposition modeling ABS”, Rapid Prototyping Journal, Vol 8, Issue 4, Pages 248–257, 2002.
15. 16. Chacon, J. M., Caminero, M. A., Garcia-Plaza, E., Nunez, P. J., “Additive manufacturing of PLA structures using fused deposition modelling: effect of process parameters on mechanical properties and their optimal selection”, Material and Design, Vol 124, Pages 143–157, 2017.
16. 17. Aydın, M., Yıldırım, F., Çantı, E., “Farklı yazdırma parametrelerinde PLA filamentin işlem performansının incelenmesi”, International Journal Of 3D Printing Technologies And Digital Industry, Cilt 3, Sayı 2, Sayfa 102-115, 2019.
17. 18. Wu, W., Geng, P., Li, G., Zhao, D., Zhang, H., Zhao, J., “Influence of layer thickness and raster angle on the mechanical properties of 3D-Printed PEEK and a comparative mechanical study between PEEK and ABS”, Materials, Vol 8, Pages 5834–5846, 2015.