TOPOLOGY OPTIMIZATION OF MOBILE TRANSPORTATION ROBOT

Öz

The main aim of this study was to decrease the weight of mobile transportation robots and to check the optimized shape using topology optimization and structural analysis. The analyses were applied using CAE Software with the methods of topology optimization and structural analysis. In the topology optimization process, the preserved areas were defined for connection and fixing areas. The aim was to decrease the weight of the robot structure and lower the energy consumption of the robotic system. After topology optimization, the structural strength analysis was applied to the new optimized structure to check the strength. The weight of the structure was decreased with a ratio of 20%. In addition to this, the structural strength of the robot was observed similar to the original body with the factor of safety value as three.

Anahtar Kelimeler

• Mobile Robot
• Robotic Arm
• Structural Analysis
• Topology Optimization
• Weight Reduction

Kaynakça

1. 1. ASTM. “Standard terminology for additive manufacturing-general principles. Part 1: Terminology” ISO/ASTM Stand. 52792, ASTM. 2015.
2. 2. Bandyopadhyay, A., Bose, S. “Additive Manufacturing, Second Edition” CRC Press Taylor & Francis Group, 2020.
3. 3. Gibson, I., Rosen, D., Stucker, B., Khorasani, M. “Additive Manufacturing Technologies Third Edition” Springer, 2021.
4. 4. Aktimur, B., Gökpınar, E. “Katmanlı Üretimin Havacılıktaki Uygulamaları”, Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji, Vol. 3, Pages. 463-469, 2014.
5. 5. Kuka Robotics, https://www.kuka.com/, April 10, 2020.
6. 6. Amazon Robotics, https://www.amazonrobotics.com/, April 10, 2020.
7. 7. Jang, K., Kim, S., Park, J. “Reactive Self-Collision Avoidance for a Differentially Driven Mobile Manipulator”, Sensors, Vol. 21, Issue 3, Pages 890-911, 2021.
8. 8. Sohlbach, L., Erchen, S., Schmidt, K. “Development of a 5 DOF manipulator for a mobile robot” 2020 21st International Conference on Research and Education in Mechatronics (REM). Cracow, Poland, 2020.

9. 9. Widhiada, W., Snthiarsa, I. G. N., Partha, C. G. I. “Design of Motion Control for Mobile Robot Manipulator”, International Journal of Mechanical Engineering and Robotics Research, Vol. 9, Issue 11, Pages 1509-1514, 2020.
10. 10. Paakkonen, R. “Cloud-based Remote Control of Autonomous Mobile Robots in Industrial Environments”, Master Thesis, Aalto University School of Electrical Engineering, Helsinki, Finland, 2020.
11. 11. Oltean, S. E. “Mobile Robot Platform with Arduino Uno and Raspberry Pi for Autonomous Navigation”, Procedia Manufacturing, Vol. 32, Pages 572-577, 2019.
12. 12. Sichkar, D. P., Bezumnov, N., Voronov, V. I., Voronova, L. I., Dankovtsev, V. I. “Moving Elements of Mobile Robots Stabilization Modelling”, Systems of Signals Generating and Processing in the Field of on-Board Communications, Moscow, Russia, 2019.
13. 13. Lee, H. Y., Murray, C. C. “Robotics in order picking: evaluating warehouse layouts for pick, place, and transport vehicle routing systems”, International Journal of Production Research, Vol. 27, Issue 18, Pages 5821-5841, 2018.
14. 14. Jagtap, M., Dhoke, A. “Topology optimization of exhaust mounting bracket.” In Tech Mahindra, Altair Technology Conference, India, 2017.
15. 15. Topaç, M. M., Karaca, M., Aksoy, B., Deryal, U., Bilal, L. “Lightweight design of a rear axle connection bracket for a heavy commercial vehicle by using topology optimisation: A case study.”, Mechanics, Vol. 26, Issue 1, Pages 64 72, 2020.
16. 16. Karaoglan, M. U., Turnalı, O. Y., Kuralay, S. N. “Hafif hizmet aracı şasi analizi ve optimizasyonu.”, Dokuz Eylul Universitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi, Vol. 18, Issue 54, Pages 502-512, 2016.
17. 17. Liu S, Li Q, Junhuan Liu, Chen W, Zhang Y. A “Realization Method for Transforming a Topology Optimization Design into Additive Manufacturing Structures”, Engineering, Vol. 4, Pages 277 285, 2018. 18. Eren, O., Sezer, H. K. “Üretken Tasarım ve Topoloji Optimizasyonu Yaklaşımlarıyla Ürün Tasarımı” Uluslararası Bilim, Teknoloji ve Sosyal Bilimlerde Güncel Gelişmeler Sempozyumu, Ankara, 2019.
18. 19. Christensen P, Anders K., “An Introduction to Structural Optimization” Springer, 2009.
19. 20. Thummar, D R. “Truss Topology Optimization Using Modified Genetic Algorithm, Master of Technology in Machine Design” Master Thesis, Department of Mechanical Engineering School of Engineering, RK University, Rajkot, Gujarat, 2014.
20. 21. Issa, M. V. “On the Accuracy and Efficiency of Cross-Entropy Method for Structural Optimization”, Master Thesis, State University of Rio de Janeiro Centro de Science and Technology Center, Rio de Janeiro, Brazil, 2019.
21. 22. Nadir W, Kim Y, Weck O. L. “Structural Shape Optimization Considering Both Performance and Manufacturing Cost” 10th AIAA/ISSMO Multidisciplinary Analysis and Optimization Conference, Albany, Newyork, 2004.
22. 23. Saleem W, Yuqing F, Yunqiao W. “Application of Topology Optimization and Manufacturing Simulations - A new trend in design of Aircraft components” Proceedings of the International Multiconference of Engineers and Computer Scientists 2008 Vol II IMECS, Hong Kong, 2008.
23. 24. Top, N., Şahin, I., Gökçe, H. “3B Yazıcı Teknolojisi için Topoloji Optimizasyonu: Otomotivde Salıncak Kolu Üzerine bir Çalışma” Third International Symposium on Industrial Design & Engineering (ISIDE), Antalya, 2018.
24. 25. Sahin, I. “Mühimmat Sistemlerinde Kullanılan Askı Kancalarında Geometri Tabanlı Topoloji Optimizasyonu” Third International Symposium on Industrial Design & Engineering (ISIDE), Antalya, 2018. 26. Cavallo, C. “All About 6061 Aluminum (Properties, Strength and Uses)”, https://www.thomasnet.com/articles/metals-metal-products/6061-aluminum/, May 04, 2021.
25. 27. Duchi, J. “Sequential Convex Programming”, https://stanford.edu/class/ee364b/lectures/seq_notes.pdf, May 04, 2021.