COMPARISON OF OPTIMIZATION METHODS FOR ADDITIVE MANUFACTURING AND MACHINING METHODS

Öz

Thanks to the developing technology and softwares, analysis and optimization of the engineering parts can be done through computer programs nowadays. Softwares play an active role not only in analysis but also in reducing the material cost as a result of lightening the part with changes in design. Manufacturing methods and comparisons of these methods with each other have always been the subject of research. Choosing the methods of manufacturing of material has a great importance for enterprise. The loads and strength of the designed part under operating conditions are very important for the manufacturer. The pros and cons of both production methods which are additive manufacturing and machining have been investigated and these methods have been compared for the use of Pet-G material. An FDM (Fused Deposition Modeling) type 3D (three-dimensional) printer has been used in the additive manufacturing method and CNC Router (Computer Numerical Control Router) has been used for the machining method. A part design created in accordance with the mentioned manufacturing methods and its mechanical properties after its twice optimization have been examined and compared. After the optimizations, the targeted reduction on the mass of production has been achieved. After the optimization process, the sample has reduced by about 63% in volume and mass according to the design program. The mass of the sample, which is approximately 300 grams, has been reduced to 100 grams. As a result of the tests, it has been observed that the strength values of the samples manufactured by machining are higher.

Anahtar Kelimeler

• Design Optimization
• Topology Optimization
• Additive Manufacturing
• Machining
• 3D printer

Kaynakça

1. 1. Erçetin, A., Aslantaş, K. and Perçin, M., "Micro milling of tungsten-copper composite materials produced through powder metallurgy method: Effect of composition and sintering temperature”, Journal of the Faculty of Engineering and Architecture of Gazi University, Vol 33, No. 4, Pages 1369-1381, 2018.
2. 2. Erçetin, A., Aslantaş, K., Özgün, Ö., "Micro-end milling of biomedical TZ54 magnesium alloy produced through powder metallurgy", Machining Science and Technology, Vol 24, No.6, Pages 924-947, 2020.
3. 3. Tezel, T., Topal, E.S., Kovan, V., “Hybrid manufacturing: an examination of the combination of additive manufacturing and machining methods”, International Journal of 3D Printing Technologies and Digital Industry, Vol. 2, Issue 3, Pages 60 – 65, 2018.
4. 4. Koda, Y., Çelebi, A., "Endüstri 4.0 Çerçevesinde Katmanli İmalatta Sensör Uygulamalari", International Journal of 3D Printing Technologies and Digital Industry, Vol 5, Issue 2, Pages 85-97, 2021.
5. 5. Çelebi, A., “Investigation of fused deposition modeling processing parameters of 3d PLA specimens by an experimental design methodology”, Materials Testing, Vol 61, No. 5, Pages 405-410, 2019.
6. 6. Börklü, H. R., “Mühendislik Tasarımı Sistematik Yaklaşım”, Sayfa 155-432, Hatiboğlu Basım ve Yayım, Ankara, 2010.
7. 7. Yaban, E., “Bir Uçağın Basınç Duvarının Yapısal Optimizasyonu”, [Structural Optimization of an Aircraft Pressure Wall], [Thesis in Turkish], Gazi Üniversitesi, Ankara, 2012.
8. 8. Teach engineering, [ article in English], https://www.teachengineering.org/activities/view/cub_creative_activity1, September 3, 2021.

9. 9. Pahl, G., Beitz, W., Feldhusen, J., Grote, K. H., “Engineering Design”, 3rd, Edition, Springer Verlag, London, 2007.
10. 10. Mayda, M., “Yeni Bir İnovatif Kavramsal Tasarım İşlem Modeli”, [A New Innovative Conceptual Design Process Model], [Thesis in Turkish], Gazi Üniversitesi, Ankara, 2013.
11. 11. Badır, M. E., “Uydu Ekipmanlarına Yönelik Topoloji Optimizasyon Metodu İle Parça Geometrisi Tasarımı, Modellenmesi, Seçici Lazerle Ergitme Yöntemi İle Üretimi Ve Analizi”, [Part Geometry Design for Satellite Equipment with Topology Optimization Method], [Thesis in Turkish], Gazi Üniversitesi, Ankara, 2019.
12. 12. Product Development with Topology Optimization Approach., https://www.poligonmuhendislik.com/blog/urun-gelistirme/topolojioptimizasyonu-yaklasimi-ile-urun-gelistirme , 06 Ekim 2021.
13. 13. Çalışkan, B., “Bir Ticari Taşıtın Makas Gözü Bağlantı Parçasının Optimizasyonu Ve Yapısal Analizler İle Tasarımın Doğrulanması”, [Optimization and Design Verification of a Commercial Vehicle's Truss Fixing Part with Structural Analysis], [Thesis in Turkish], İstanbul Teknik Üniversitesi, İstanbul, 2018.
14. 14. Topaç, M. M., Bahar, E., Kaplan, A., Sarıkaya, E. Z., “Lower wishbone design for military vehicle independent front suspension with the aid of topology optimization”. IDEFIS 2017: 2nd International Defence Industry Symposium, Pages 333-342, Kırıkkale, 2017.
15. 15. Von Mises Stretch, http://www2.isikun.edu.tr/personel/ahmet.aran/, 10 Aralık 2020.
16. 16. Evlen, H., “Investigation of the Effects of Fill Ratio on the Mechanical Properties of TPU and TPE Samples Produced in 3D Printer”, DEUFMD, Vol. 21, Issue 63, Pages 793-80, 2019.
17. 17. Evlen, H., Erel, G., Yılmaz, E., “Investigation of the Effect of Occupancy Rate on Part Strength in Open and Closed Systems”, Politeknik Dergisi Vol.21, Issue 3, Pages 651-662, 2018.
18. 18. Özsoy, K , Şentürk, E , Aydoğan, D , Korucu, Ö ., "3B Yazıcı Teknolojisi için Topoloji Optimizasyonu: N95 Maske Üzerine Bir Çalışma". Türk Doğa ve Fen Dergisi, 9, 152-159, 2020.