Toz Metalurjisi ile Üretilmiş Al/SiC ve Al/B4C Metal Matrisli Kompozitlerin Mikroyapı, Fiziksel ve Mekanik Özellikleri

Yıl 2021, Cilt: 2 Sayı: 2, 72 - 89, 01.12.2021

Polen Şanlı , Muammer Gavas

Öz

Bu çalışmada, farklı takviye oranlarında (%8, %16, %24) silisyum karbür (SiC) ve bor karbür (B4C) ile takviyelendirilmiş alüminyum (Al) matrisli kompozitler toz metalurjisi yöntemi ile üretilmiştir. Tozlar karıştırıldıktan sonra, elde edilen toz karışımları tek eksenli bir hidrolik pres ile preslenmiştir. Silindirik blok şeklinde preslenen ham numuneler, farklı sıcaklıklarda (540°C, 580°C, 620°C) ve sürelerde (2 ve 4 saat) sinterleme işlemine tabi tutulmuştur. Sinterleme sonrası numunelere metalografik numune hazırlama işlemleri uygulanarak, yoğunluk ve sertlik ölçümleri yapılmış, ardından mikroyapı incelemeleri optik mikroskop, taramalı elektron mikroskobu (SEM) ve enerji dağılım spektrometresi (EDX) ile gerçekleştirilmiş ve sonuçlar değerlendirilmiştir. Böylece değişen takviye oranı, sinterleme sıcaklığı ve sinterleme süresinin üretilen kompozitlerin mikroyapı, fiziksel ve mekanik özelliklerine etkisi belirlenmiş ve karşılaştırma yapılmıştır.

Anahtar Kelimeler

B4C, Metal matrisli kompozitler, Toz metalurjisi, SiC

Microstructure, Physical and Mechanical Properties of Al/SiC and Al/B4C Metal Matrix Composites Produced by Powder Metallurgy

Öz

In this study, aluminum (Al) matrix composites reinforced with silicon carbide (SiC) and boron carbide (B4C) in different weight ratios (8 wt.%, 16 wt.%, 24 wt.%) were produced by powder metallurgy method. After mixing, the resulting powder mixtures were compressed with a uniaxial hydraulic press. Compressed cylindrical block-shaped raw samples were subjected to sintering at different temperatures (540°C, 580°C, 620°C) and times (2 and 4 hours). After sintering samples, metallographic sample preparation processes were applied, the density and hardness measurements were made, then the microstructure examinations were performed by optical microscope, scanning electron microscope (SEM) and energy distribution spectrometer (EDX) and the results were evaluated. Thus, the effect of changing reinforcement rate, sintering temperature and sintering time on the microstructure and mechanical properties of the composites produced was determined and a comparison was made. As a result of the study, it was determined that the optimum values were obtained in samples sintered at 620°C for 4 hours. The highest hardness values obtained were determined as ~92 HV for 24wt.% SiC reinforced samples sintered at 620°C for 4 hours and, ~60 HV for 8wt.% B4C reinforced samples sintered at 620°C for 4 hours. Thus, compared to ~54 HV value, which is the highest hardness value obtained in unreinforced Al samples sintered at 620°C for 4 hours, 70% higher hardness was obtained in SiC samples and 11% higher in B4C samples. Although the B4C hardness value is higher than SiC, it was interpreted that the difference in the matrix/reinforcement particle size ratio was effective in obtaining these hardness results.

Anahtar Kelimeler

B4C, Metal matrix composites, Powder metallurgy, SiC

Kaynakça

• Ay H., Toz Metalurjisi Yöntemi ile Üretilen AA7075 Alüminyum Alaşımına Ti ve B4C İlavesinin Aşınma Davranışı Üzerine Etkisinin İncelenmesi. Karabük Üniversitesi Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi (Basılmış), 2014.
• Baradeswaran A., Elaya Perumal A., Influence of B4C on The Tribological and Mechanical Properties of Al 7075-B4C Composites. Composites Part B: Engineering 54, 146-152, 2013.
• Basavarajappa M. P., Parashivamurthy K. I., Synthesis and Tribological Characterization of In-situ Prepared Al-TiC Composites, American Journal of Materials Science 7(4), 108-111, 2017.
• Bhushan R. K., Effect of SiC Particle Size and Weight % on Mechanical Properties of AA7075 SiC Composite. Advanced Composites and Hybrid Materials 4, 74-85, 2021.
• Çelik, Y. H., Kilickap, E., Hardness and Wear Behaviours of Al Matrix Composites and Hybrid Composites Reinforced with B4C and SiC. Powder Metallurgy and Metal Ceramics 57(9), 613-622, 2019.
• Çolak N. Y., Turhan H., Toz Metalurjisi Yöntemi ile Üretilen Al-Si/B4C Kompozit Malzemenin Mikroyapı ve Mekanik Özelliklerinin Araştırılması. Fırat Üniversitesi Mühendislik Bilimleri Dergisi 28(2), 259-266, 2016.
• Dangarikar, S. U., Dhokey, N. B., Study of Hot-Pressed Sintering of Premixed Al7075 Based B4C Reinforced Composites on Wear Mechanism Materials Today: Proceedings, 2020.
• Gökmeşe H., Taşçı U., Bostan B., AA 2014 Al Matrisli B4C Parçacık Takviyeli Kompozitlerin Mikro Yapı ve Aşınma Davranışının İncelenmesi, Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji 1(4), 161-168, 2013.
• Hu B., Warzel III R., Ropar S., Neilan A., The Effect of Porosity on Machinability of PM Materials. International Journal of Powder Metallurgy 53(1), 27–36, 2017.
• Jeevan V., Rao C.S.P., Selvaraj N., Compaction, Sintering and Mechanical Properties of Al–SiCp Composites. International Journal of Mechanical Engineering and Technology 3(3), 565-573, 2012.
• Kalaycıoğlu, A. S., SiC Tane Katkılı Alüminyum Kompozitlerin Toz Metalurjisi ile Üretimi ve Karakterizasyonu, Dokuz Eylül Üniversitesi Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi (Basılmış), 2010.
• Kalemtaş A., Metal Matrisli Kompozitlere Genel Bir Bakış. Putech & Composites 22, 18-30, 2014.
• Karakoç H., Ovalı İ., Dündar S., Çıtak R., Wear and Mechanical Properties of Al6061/SiC/B4C Hybrid Composites Produced with Powder Metallurgy. Journal of Materials Research and Technology 8(6), 5348-5361, 2019.
• Kevenlik, O. F., Toz Metalurjisi Yöntemi ile SiC Takviyeli Al 2014 Esaslı Kompozit Üretimi ve Mekanik Özelliklerinin İncelenmesi, Kırıkkale Üniversitesi Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi (Basılmış), 2013.
• Kumdalı F., Alüminyum Matrisli B4C Takviyeli Kompozitlerin Toz Metalurjisi Yöntemi ile Üretimi. Yıldız Teknik Üniversitesi Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi (Basılmış), 2008.
• Lindroos V. K., Talvitie M. J., Recent Advances in Metal Matrix Composites. Journal of Materials Processing Technology 53(1-2), 273-284, 1995.
• Mohapatra S., Chaubey A. K., Mishra D. K., Singh S. K., Fabrication of Al-TiC Composites by Hot Consolidation Technique: Its Microstructure and Mechanical Properties. Journal of Materials Research and Technology 5(2), 117–122, 2016.
• Salman, K. D., Comparison the Physical and Mechanical Properties of Composite Materials (Al/SiC and Al/B4C) Produced by Powder Technology, Journal of Engineering 23(10), 85-96, 2017.
• Shaikh M. B. N., Arif S., Aziz T., Waseem A., Shaikh M. A. N., Ali M., Microstructural, Mechanical and Tribological Behavior of Powder Metallurgy Processed SiC and RHA Reinforced Al-Based Composites, Surfaces and Interfaces 15, 166-179, 2019.
• Surya, M. S., Effect of SiC Weight Percentage and Sintering Duration on Microstructural and Mechanical Behaviour of Al6061/SiC Composites Produced by Powder Metallurgy Technique. Silicon, 2021.
• Surya, M. S., Prasanthi, G., Manufacturing, Microstructural and Mechanical Characterization of Powder Metallurgy Processed Al7075/SiC Metal Matrix Composite. Materials Today: Proceedings 39, 1175-1179, 2021.
• Venkatesh B., Harish B., Mechanical Properties of Metal Matrix Composites (Al/SiCp) Particles Produced by Powder Metallurgy. International Journal of Engineering Research and General Science 3(1), 1277-84, 2015.
• Zaki, M. U., Hussain, S., Impact of Addition of Manganese and Boron Carbide on Aluminium Metal Matrix Composites Using Powder Metallurgy Process. Materials Today: Proceedings, 2020.