Investigation of Static Strain Aging Behaviour of AISI 304 Austenitic Stainless Steel
Öz
In this study, the change in the material's mechanical properties by the static strain ageing process after the pre-deformation applied to AISI 304 austenitic stainless steel was investigated and analysed. The samples were first applied to 5% pre-deformation and then annealed in the oven at 150°C, 250°C, 400°C and 550°C in separate groups for 30 and 60 minutes. The data obtained by performing hardness and tensile tests after static strain ageing were compared, and the interaction between test parameters and these parameters was investigated by performing Pareto analysis. As a result of the study, the highest tensile strength and hardness values were observed in the samples applied static strain ageing for 60 minutes at 150°C. The yield and tensile strengths of the as-received material increased by 10% with the ageing process. It was determined that these values decreased from 400°C. In addition, as a result of Pareto analysis, it was determined that the temperature value is the most critical parameter affecting the results.
Anahtar Kelimeler
AISI 304, Static strain aging, Pareto, Tensile test
Destekleyen Kurum
Giresun University
Proje Numarası
FEN-BAP-A-230218-17
Teşekkür
This work is supported by Giresun University Scientific Research Project Office.
Kaynakça
- A. H. Cottrell, and B. A. Bilby, (1949). Dislocation Theory of Yielding and Strain Ageing of Iron The Steady Non-Uniform State for a Liquid. Proc. Phys. Soc. A, 62, 49–62.
- Altan Özbek, N., Çiçek, A.,, Gülesin, M., and Özbek, O., (2017). AISI 304 ve AISI 316 Östenitik Paslanmaz Çeliklerin İşlenebilirliğinin Değerlendirilmesi. Politeknik Dergisi, 20(1), 43–49.
- Altuntaş, O., Özer, E., and Gürel, A., (2020). Sade Karbonlu Toz Metal Bir Çeliğin Çekme Dayanımına Statik Deformasyon Yaşlanma İşleminin Etkilerinin Araştırılması. Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji, 8(3), 671–680.
- ASTM E8, (2010). ASTM E8/E8M standard test methods for tension testing of metallic materials 1. Annual Book of ASTM Standards 4, (C), 1–27.
- Çetin, A., (2022). Gerinim yaşlanması
- Dieter, G.E., (1961). Mechanical Metallurgy. McGraw-Hill Book Company.
- Gupta, A.K.,, Krishnamurthy, H.N.,, Singh, Y.,, Prasad, K.M., and Singh, S.K., (2013). Development of constitutive models for dynamic strain aging regime in Austenitic stainless steel 304. Materials and Design, 45, 616–627.
- Kaçar, R.,, Emre, H.E., and Sinoplu, Ö., (2011). Dubleks Paslanmaz Çeliklerin Statik Yaşlanma Davranışları. 6. International Advanced Technologies Symposium, (May), 16–18.
- Lee, S.H.,, Choi, J.Y., and Nam, W.J., (2009). Hardening Behavior of a 304 Stainless Steel Containing Deformation-Induced Martensite during Static Strain Aging. Materials Transactions, 50(4), 926–929.
- Lee, C., and Zuidema, B.K., (1994). On High Strenght Sheet Steels For The Automotive Industry. In: Proc. Symp, Iron And Steel Society, Warrendale PA, 103.
kapsamında lisanslanmıştır.