The Effect of Drying Control Chemicals on Coatings Morphology at SiO2 Coatings Prepared by Sol-Gel Method on Ti6Al4V Alloy

Öz

Ti6Al4V is the most widely used titanium alloy in today's biomaterial applications. It is preferred in biomedical applications due to its non-toxic/allergenic effect and good mechanical properties. This study was carried out with the aim of improving the corrosion resistanceof this alloy preffered due to its many positive properties. In this study, Ti6Al4V alloy was coated with SiO2 solution by using sol-gel method prepared by adding different drying control chemicals after surface preparation. Then, X-Ray Diffraction (XRD) and scanning electron microscopy (SEM) analyses were performed. As a result of these analyses, it was observed that the used drying control chemicals prevented the cracks that may occur in the structure, shortened the gap distance between the formed crack structures and tended to preserve the integrity of the structure.

Anahtar Kelimeler

• Biomaterial,Coating,Ti6Al4V,SiO2,Sol-Gel

Ti6Al4V Alaşımı Üzerine Sol-Jel Yöntemi ile Yapılan SiO2 Kaplamalarda Kurutma Kontrol Kimyasallarının Kaplama Morfolojisine Etkisi

Öz

Ti6Al4V, günümüzün biyomalzeme uygulamalarında en çok kullanılan titanyum alaşımıdır. İnsan vücudu içinde toksik/alerjenik etki oluşturmaması ve mekanik özelliklerinin iyi olması nedenleri ile biyomedikal uygulamalarda tercih edilmektedir. Yapılan çalışma, birçok olumlu özellikleri nedeni ile tercih edilen bu korozyon dayanımının geliştirilmesi amacı ile gerçekleştirilmiştir. Bu çalışmada Ti6Al4V alaşımı, yüzey hazırlıkları yapıldıktan sonra, farklı kurutma kontrol kimyasalları eklenerek hazırlanan SiO2 çözeltisi kullanılarak sol-jel yöntemi ile kaplanmıştır. Sonrasında X-Işını Kırınımı (XRD) ve taramalı elektron mikroskobu (SEM) analizleri gerçekleştirilmiştir. Yapılan analizler sonucunda kullanılan kurutma kontrol kimyasallarının yapıda oluşması muhtemel çatlakları önlediği, oluşan çatlak yapılarının arasındaki boşluk mesafesini kısalttığı, yapının bütünlüğünü koruma eğiliminde olduğu gözlemlenmiştir.

Anahtar Kelimeler

• Ti6Al4V,Sol-jel,Kaplama,SiO2,Biyomalzeme

Kaynakça

1. Ibrahim M.Z., Sarhan, A.A.D., Yusuf F., Hamdi M. Biomedical materials and techniques to improve the tribological, mechanical and biomedical properties of orthopedic implants-A review article, Journal of Alloys and Compounds, 714 636-667, 2017.
2. Lin H.D. Tiny surface defect inspection of electronic passive components using discrete cosine transform decomposition and cumulative sum techniques, Image and Vision Computing, 26 603-621, 2008.
3. Kokubo T., Kim H.M., Kawashita M. Novel bioactive materials with different mechanical properties, Biomaterials, 24:13 2161-2175, 2003.
4. Rafieerad A.R., Bushroa A.R., Nasiri-Tabrizi B., Vadivelu J., Baradaran S., Mesbah M., Akhtari Z.M. Mechanical properties, corrosion behavior and in-vitro bioactivity of nanostructured PD/PDO coating on Ti-6Al-7Nb implant, Materials and Design, 103 10-24, 2016.
5. Velten D., Biehl V., Aubertin F., Valeske B., Possart W., Breme, J. Preparation of TiO2 layers on cp-Ti and Ti6Al4V by thermal and anodic oxidation and by sol-gel coating techniques and their characterization Journal of Biomedical Materials Research, 59:1 18-28, 2002.
6. Kang S.H., Kim J.Y., Kim H.S., Sung Y.E. Formation and mechanistic study of self-ordered TiO2 nanotubes on Ti substrate, Journal of Industrial and Engineering Chemistry, 14:1 52-59, 2008.
7. Rafieerad A.R., Bushore A.R., Zalnezhad E., Sarraf M., Basirun W.J., Baradaran S., Nasiri-Tabrizi B. Microstructural development and corrosion behavior of self-organized TiO2 nanotubes coated on Ti-6Al-7Nb, Ceramics International, 41:9 10844-10855, 2015.
8. Liu X., Chu P.K., Ding C. Surface modification of titanium, titanium alloys, and related materials for biomedical applications, Materials Science and Engineering: R: Reports, 47:3-4 49-121, 2004.

9. Rahmati B., Zalnezhad E., Sarhan A.D.D., Kamiab Z., Nasiri Tabrizi B., Abas, W.A.B. W. Enhancing the adhesion strength of tantalum oxide ceramic thin film coating on biomedical Ti-6Al-4V alloy by thermal surface treatment, Ceramics International, 41:10 13055-13063, 2015.
10. Saenz de Viteri V., Barandaki M.G., Ruiz de Gopegui U., Bayon R., Zubizarreta C., Fernandez X., Igartua A. Agullo-Rueda F. Characterization of Ti-C-N coatings deposited on Ti6Al4V for biomedical applications, Journal of Inorganic Biochemistry, 117 359-366, 2012.
11. Cotolan N., Rak M., Bele M., Cör A., Muresan L.M. Milošev I. Sol-gel synthesis, characterization and properties of TiO2 and Ag-TiO2coatings on titanium substrate, Surface and Coatings Technology, 307 790-799, 2016.
12. Sobiyi K., Akinlabi E. Microstructural Investigation of Ti Coating on Ti6Al4V by Laser Cladding, Materials Today: Proceedings, 4:2 244-249, 2017.
13. Avci M., Yilmaz B., Tezcaner A., Evis Z. Strontium doped hydroxyapatite biomimetic coatings on Ti6Al4V plates, Ceramics International, 43:12 9431-9436, 2017.
14. Hernández-Barrios C.A., Cuao C.A., Jaimes M.A., Coy A.E., Viejo F. Effect of the catalyst concentration, the immersion time and the aging time on the morphology, composition and corrosion performance of TEOS-GPTMS sol-gel coatings deposited on the AZ31 magnesium alloy, Surface and Coatings Technology, 325 257-269, 2017.
15. Tong W., Xiong D., Zhou H. TMES-modified SiO2 matrix non-fluorinated superhydrophobic coating for long-term corrosion resistance of aluminium alloy, Ceramics International, 46:1 1211-1215, 2020.
16. Montazeri N., Jahandideh R., Biazar E. Synthesis of fluorapatite-hydroxyapatite nanoparticles and toxicity investigations, International Journal of Nanomedicine, 6 197-201, 2011.
17. Guo X., Zhang Z., Ding X., Shen Q., Wu C., Zhang L., Yang H. Synthesis and application of several sol-gel derived Materials via sol-gel process combining with other Technologies: a review, Journal of Sol-Gel Science and Technology, 79:2 328-358, 2016.
18. Lee Y.T., Jen H.H.A Raman study of the effect of formamide on the tetramethoxysilane sol-gel process, Journal of Non-Crystalline Solids, 342:1-3 39-45, 2004.
19. Cantürk Ö.D., Kaya N., Sol-Jel Yöntemiyle Üretilen Alümina Alkojelin Fizikokimyasal ve Yapısal Özellikleri Üzerine Kurutma Türünün Etkisi, Politeknik Dergisi, 2020. doi: 10.2339/politeknik.456871
20. Kesim M.T., Durucan C. Indium tin oxide thin films elaborated by sol-gel routes: The effect of oxalic acid addition on optoelectronic properties, Thin Solid Films, 545 56-63, 2013