NİĞDE BÖLGESİ KALSİTLERİNİN KAZISINDA KOLLU GALERİ AÇMA MAKİNESİ KULLANILABİLİRLİĞİNİN ARAŞTIRILMASI

Yıl 2018, Cilt: 7 Sayı: 2, 829 - 837, 20.07.2018

Ramazan Çomaklı

https://doi.org/10.28948/ngumuh.445262

Öz

Niğde
bölgesinde yer alan kalsit işletmeleri açık ocak madenciliği yöntemi ile
işletilmekte ve bu işletmelerde kazı için delme patlatma yöntemleri
kullanılmaktadır. Delme ve patlatma yönteminin masrafları toplam işletme
masrafları içerisinde önemli bir parametredir. Bunun yanında özellikle verimsiz
delme patlatma uygulamalarından sonra oluşan büyük bloklar da bu maliyeti
artıracaktır. Mekanize kazı yöntemlerinin uygulandığı işletmelerde ise kazı
işlemleri daha hızlı olmakta ve uygun kazıcının seçilmesi ile üretim maliyeti
delme patlatma yöntemine kıyasla daha az olmaktadır. Yapılan bu çalışmada Niğde
bölgesinde bulunan kalsit işletmelerinde kollu galeri açma makinesi (KGAM)
kullanılabilirliği ve performansları araştırılmıştır. Bu kapsamda farklı kalsit
işletmelerine ait hammadde sahalarından numuneler alınmış ve laboratuvar
deneyleri ile fiziksel ve mekanik özellikleri belirlenmiştir. Farklı
araştırmacılar tarafından geliştirilen performans tahmin modelleri kullanılarak
kalsit kazısı için KGAM kazı performans tahmini yapılmıştır. Ayrıca, KGAM
kullanımında önemli bir parametre olan kesici uç tüketimi de teorik yaklaşımlar
kullanılarak hesaplanmıştır.

Anahtar Kelimeler

Kollu galeri açma makinesi, Kalsit, Performans tahmini, Kesici uç tüketimi, Anlık kazı hızı

INVESTIGATION OF THE USABILITY OF ROADHEADERS IN EXCAVATION OF CALCITE IN NİĞDE REGION

Öz

Open-pit
mining method is used in many calcite mines located in Niğde region and
drilling and blasting method is applied in these mines for excavation. The
application costs of drilling and blasting are important parameters in total
operating costs. In addition, especially large blocks obtained after
inefficient drilling blasting applications will increase this cost. The
excavations are faster in mines that using the mechanical excavators and by
selecting the proper machine, the cost of production is less than the drilling
and blasting method. In this study, the usability and performances of
roadheaders were investigated in calcite mines in Niğde region. In this
purpose, calcite samples were collected from the different calcite mines in
Niğde region and firstly, their physical and mechanical properties were
determined by laboratory tests. Then, for calcite excavation, the performance
of KGAM was estimated with using performance prediction models developed by
different researchers. In addition, cutter consumption rate, an important
parameter in the use of KGAM, has been estimated using theoretical models.

Anahtar Kelimeler

Roadheaders, Calcite, Performance prediction, Cutter consumption, Instantaneous cutting rate

Kaynakça

• [1] PAKES, G., “Selection of Methods”, World Tunneling, 4, 9, November, 1991.
• [2] ESKİKAYA, Ş., “Ereğli Kömür İşletmesi Kozlu ve Armutçuk Bölgelerinde Hazırlık Galerilerinin Galeri Açma Makinaları ile Açılması ve En Uygun Makina Tiplerinin Tespiti, TÜBİTAK Projesi, Proje No: 542, 1981.
• [3] ÖZDEMİR, L., (Çeviren : Prof. Dr. Ş. Eskikaya), "Sert Kayaç Madenciliği Mekanik Kazı Teknolojisinde Son Gelişmeler", İTÜ Maden Fakültesi Tünel ve Galeri Açma Meslek içi Semineri, 1994.
• [4] BREITRICK. M.E., “Using a Roadheader for Underground Gold Mining” Mining Engineering, 43-46, March, 1998.
• [5] BİLGİN, N., ÇOPUR, H., BALCI, C., TUNÇDEMİR, H., TUMAÇ, D., FERİDUNOĞLU, C., “Selection of a mechanical mining system for an underground chromite mine”, in: Int. Symp. Mine Plann. Equip. Selection. Banff Alberta Canada, pp. 120–144, 2005.
• [6] TUNÇDEMIR, H., COPUR, H., FERIDUNOGLU, C., BILGIN, N., “Possibility of Using Mechanical Miners in Underground Chromite Mines’ Ore Productions and Two Different Examples”, 18th Int. Mining Congress, 135–141, 2003.
• [7] TUNÇDEMIR, H., “Investigation into Application of Boom Type Machines for Mineral Excavations”, PhD Thesis. Istanbul Technical University, 2002.
• [8] COMAKLI, R., KAHRAMAN, S., BALCI, C., “Performance Prediction of Roadheaders in Metallic Ore Excavation” Tunneling and Underground Space Technology 40, 38–45, 2014.
• [9] OCAK, İ., “Comparison of Machine Utilization Time and Performance for Roadheader and Impact Hammer in Kadikoy – Kartal Metro Tunnels (Istanbul)”, 8th International Scientific Conference, Modern Management of Mine Producing, Geology and Environmental Protection. Varna–Bulgaria, 269–276, 2008.
• [10] OCAK, İ., BILGIN, N., “Comparative Studies on the Performance of a Roadheader, Impact Hammer and Drilling and Blasting Method in the Excavation of Metro Station Tunnels in Istanbul”, Tunnelling and Underground Space Technology 25, 181–187, 2010.
• [11] ROSTAMI, J., OZDEMIR, L., NEIL, D.M., “Performance Prediction: a Key Issue in Mechanical Hard Rock Mining”, Min. Eng. 1263–1267, 1994.
• [12] ULUSAY, R., HUDSON, J.A. (EDS.), “The Complete ISRM Suggested Methods for Rock Characterization, Testing and Monitoring”, ISRM Turkish National Group, Ankara, Turkey, 2007.
• [13] ALBER, M., YARALI, O., DAHL, F., BRULAND, A., KASLING, H., MICHALAKOPOULOS, T.N., CARDU, M., HAGAN, P., AYDIN, H., OZARSLAN, A., “ISRM Suggested Method for Determining the Abrasivity of Rock by the Cerchar Abrasivity Test” Rock Mechanics and Rock Engineering, 47, 261–266, 2014.
• [14] GEHRING, K.H., “A Cutting Comparison”, Tunnels Tunnell., 27–30, 1989.
• [15] THURO, K., PLINNINGER, R.J., “Roadheader Excavation Performance – Geological and Geotechnical Influences”, in: The 9th ISRM Congress, Theme 3: Rock Dynamics and Tectonophysics/Rock Cutting and Drilling. Paris, p. 1241–1244, 1999.
• [16] TUMAC, D., BILGIN, N., FERIDUNOGLU, C., ERGIN, H., “Estimation of Rock Cuttability From Shore Hardness and Compressive Strength Properties”, Rock Mech Rock Eng. 40, 477–490, 2007.
• [17] BILGIN, N., DINCER, T., COPUR, H., ERDOGAN, M., “Some Geological and Geotechnical Factors Affecting the Performance of a Roadheader in an Inclined Tunnel”, Tunnelling and Underground Space Technology, 19, 629–636, 2004.
• [18] BILGIN, N., SEYREK, T., ERDING, E., SHAHRIAR, K., “Roadheaders Glean Valuable Tips for Istanbul Metro”, Tunnels and Tunnelling International, 22, 29–32, 1990.
• [19] BALCI, C., DEMIRCIN, M.A., COPUR, H., TUNCDEMIR, H., “Estimation of Optimum Specific Energy Based on Rock Properties for Assessment of Roadheader Performance”, Journal of the South African Institute of Mining and Metallurgy 104, 633–641, 2004.
• [20] COPUR, H., OZDEMIR, L., ROSTAMI, J., “Roadheader Applications in Mining and Tunneling”, Mining Engineering, 1998.
• [21] COPUR, H., ROSTAMI, J., OZDEMIR, L., BILGIN, N., “Studies on Performance Prediction of Roadheaders”, in: Proceedings of the 4th International Symposium on Mine Mechanization and Automation. Brisbane, Queensland, Australia, p. 4A1–4A7, 1997.
• [22] JOHNSON, S.T., FOWELL, R.J., “Compressive Strength is not Enough: Assessing Pick Wear Rates for Drag Tool Equipped Machines”, in: Hartman, H.L. (Ed.), 27th US Rock Mech. Symp. Tuscazoosa, AL. AIME, New York, pp. 840–845, 1986.
• [23] OZDEMIR, L., “Mechanical Tunneling, Raise Boring and Shaft Drilling”, Short Course. Golden, Colorado, 1998.
• [24] KAHRAMAN, E., KAHRAMAN, S., “The Performance Prediction of Roadheaders from Easy Testing Methods”, Bulletin of Engineering Geology and the Environment 75, 1585–1596, 2016.