EN
An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding
Öz
In this study, the optimized injection parameters for a feedstock obtained by mixing the powder of Ti-6Al-7Nb and 31wt% binder system (comprised of high-density polyethylene, Polypropylene, PEG 20000, paraffin wax and stearic acid), were determined. In order to investigate the fabrication of a component, flow rate, injection pressure, holding pressure, injection temperature and mold temperature were studied at three levels to obtain the optimum injection parameters. It was proven that for feedstock comprised of 69wt% Ti-6Al-7Nb powder, the suitable set of injection parameters were as follows: flow rate of 20 cm3/s, injection pressure of 1300 bar, holding pressure of 60%, injection temperature of 140 °C and mold temperature of 60 °C. At the end of the experiments the tensile strength of specimens fabricated with optimum parameters, were as high as 631 MPa
Anahtar Kelimeler
Ayrıntılar
Birincil Dil
Türkçe
Konular
-
Bölüm
-
Yayımlanma Tarihi
1 Haziran 2017
Gönderilme Tarihi
1 Haziran 2017
Kabul Tarihi
-
Yayımlandığı Sayı
Yıl 2017 Cilt: 20 Sayı: 2
APA
Subaşı, M., Safarıan, A., & Karataş, Ç. (2017). An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding. Politeknik Dergisi, 20(2), 393-399. https://izlik.org/JA74RK26DE
AMA
1.Subaşı M, Safarıan A, Karataş Ç. An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding. Politeknik Dergisi. 2017;20(2):393-399. https://izlik.org/JA74RK26DE
Chicago
Subaşı, Mehmet, Asghar Safarıan, ve Çetin Karataş. 2017. “An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding”. Politeknik Dergisi 20 (2): 393-99. https://izlik.org/JA74RK26DE.
EndNote
Subaşı M, Safarıan A, Karataş Ç (01 Haziran 2017) An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding. Politeknik Dergisi 20 2 393–399.
IEEE
[1]M. Subaşı, A. Safarıan, ve Ç. Karataş, “An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding”, Politeknik Dergisi, c. 20, sy 2, ss. 393–399, Haz. 2017, [çevrimiçi]. Erişim adresi: https://izlik.org/JA74RK26DE
ISNAD
Subaşı, Mehmet - Safarıan, Asghar - Karataş, Çetin. “An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding”. Politeknik Dergisi 20/2 (01 Haziran 2017): 393-399. https://izlik.org/JA74RK26DE.
JAMA
1.Subaşı M, Safarıan A, Karataş Ç. An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding. Politeknik Dergisi. 2017;20:393–399.
MLA
Subaşı, Mehmet, vd. “An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding”. Politeknik Dergisi, c. 20, sy 2, Haziran 2017, ss. 393-9, https://izlik.org/JA74RK26DE.
Vancouver
1.Mehmet Subaşı, Asghar Safarıan, Çetin Karataş. An Investigation of Injection Parameters of Ti-6Al- 7NbFabricated by Powder Injection Molding. Politeknik Dergisi [Internet]. 01 Haziran 2017;20(2):393-9. Erişim adresi: https://izlik.org/JA74RK26DE