Comparison of Convective Heat Transfer Effects in Impinging Slot and Circular Jets Confined by Plates With Different Inclination Angles

Öz

In this study, the effects of heat transfer characteristics along the target impingement plate surfaces in impinging slot and circular turbulent air jets confined by plates with different inclination angles are experimentally investigated. Surface temperature measurements were conducted with a thermal imaging camera on the target impingement plate for inclination angles of confinement plate θ = 0°, 15°, 30° and 45°, rate of plate-to-plate spacing H/W(D) = 0.5, 1, 3, 6 and Reynolds numbers (Re) 20000 and 30000. The Nusselt distributions calculated from the measured temperature values are analyzed and the changes are evaluated according to the confining plate inclination angle, Reynolds number and rate of plate-to-plate spacing parameters. For both slot and circular jets, secondary top points become visible in the Nusselt number distributions on the impingement plate when the rate of plate-to-plate spacing is H/W(D)≤1 and the inclination angle of confinement plate is θ≤15°. As the interval among the plates increases, the influence of the secondary top points decreases and their positions shift towards the plate ends. As the angle of inclination of the confining plate increases, the secondary top points disappear rapidly for slot jets, but more slowly for circular jets.

Anahtar Kelimeler

• Circular jet
• Inclined confined plate
• Nusselt distributions
• Secondary top points
• Slot jet

Farklı Eğim Açılı Levhalarla Sınırlandırılmış Çarpan Slot ve Dairesel Jetlerde Taşınımla Isı Transferi Etkilerinin Karşılaştırılması

Öz

Bu çalışmada, farklı eğim açılı levhalarla sınırlandırılmış çarpan slot ve dairesel türbülanslı hava jetlerinde, hedef çarpma levhası yüzeyleri boyunca ısı transfer karakteristikleri etkileri deneysel olarak incelenmiştir. Sınırlayıcı levha eğim açısının θ = 0°, 15°, 30° ve 45°, levhalar arası açıklık oranı H/W(D) = 0.5, 1, 3, 6 ve Reynolds sayısının 20000 ile 30000 değerleri için hedef çarpma levhası boyunca termal kamera ile yüzey sıcaklık ölçümleri yapılmıştır. Ölçümlenen sıcaklık değerlerinden hesaplanan Nusselt dağılımları, sınırlayıcı levha eğim açısı, Reynolds sayısı (Re) ve levhalar arası açıklık oranı parametrelerine göre incelenip değişimler değerlendirilmiştir. Hem slot hem de dairesel jetlerde, levhalar arası açıklık oranının H/W(D)≤1 ve sınırlayıcı levha eğim açısının θ≤15° olduğu durumlarda, çarpma levhası üzerindeki Nusselt sayısı dağılımlarında ikincil pikler oluşmaktadır. Levhalar arası açıklık oranı arttıkça, ikincil piklerin etkisi azalmakta ve konumları levha uçlarına doğru kaymaktadır. Artan sınırlandırıcı levha eğim açısı ile birlikte, slot jetlerde ikincil pikler hızla kaybolurken, dairesel jetlerde bu durumun daha yavaş olduğu gözlenmiştir.

Anahtar Kelimeler

• Dairesel jet
• eğimli sınırlandırıcı levha
• ikincil artışlar
• Nusselt dağılımları
• Slot jet

Kaynakça

1. Danek, C. J. (1995). Heat transfer under impinging jets at very close jet-to-target spacings. [Doktora Tezi, Stanford Üniversitesi, Ann Arbor, ABD].
2. Gardon, R., & Akfirat, J. C. (1965). The role of turbulence in determining the heat-transfer characteristics of impinging jets. International Journal of Heat and Mass Transfer, 8(10), 1261-1272. https://doi.org/10.1016/0017-9310(65)90054-2
3. Livingood, J. N. B., Hrycak, P., & Hrycak, P. (1973), Impingement heat transfer from turbulent air jets to flat plates: a literature survey. NASA Technical Memorandum, Ohio, ABD. https://ntrs.nasa.gov/api/citations/19730016200/downloads/19730016200.pdf
4. Senter, J., & Solliec, C. (2007). Flow field analysis of a turbulent slot air jet impinging on a moving flat surface. International Journal of Heat and Fluid Flow, 28(4), 708-719. https://doi.org/10.1016/j.ijheatfluidflow.2006.08.002
5. Cavadas, A. S., Pinho, F.T., & Campos, J. B. L. M. (2012). Laminar flow field in a viscous liquid impinging jet confined by inclined plane walls. International Journal of Thermal Sciences, 59, 95-110. https://doi.org/10.1016/j.ijthermalsci.2012.04.004
6. Özmen, Y., & Kınay, H. (2023). Investigation of flow and heat transfer characteristics of impinging slot jets confined with inclined plates. Heat Mass Transfer, 59, 509–534. https://doi.org/10.1007/s00231-022-03279-y
7. Kunugi, T., & Kawamura, H. (1987, Ekim). Application of a Two-Equation Turbulence Model to Heat Transfer and Fluid Flow of an Impinging Round Jet. 2nd International Symposium on Transport Phenomena in Turbulent Flows, Tokyo, Japonya.
8. Chiriac, V. A., & Ortega, A. (2002). A numerical study of the unsteady flow and heat transfer in a transitional confined slot jet impinging on an isothermal surface. International Journal of Heat and Mass Transfer, 45(6), 1237-1248. https://doi.org/10.1016/S0017-9310(01)00224-1

9. Yousefi-Lafouraki, B., Ramiar, A., & Ranjbar, A. A. (2014). Laminar forced convection of a confined slot impinging jet in a converging channel. International Journal of Thermal Sciences, 77, 130-138. https://doi.org/10.1016/j.ijthermalsci.2013.10.014
10. Schrader, H. (1961). Trocknung feuchter Oberflächen mittels Warmluftstrahlen, VDI-Verl. Düsseldorf.
11. Goldstein, R. J., Sobolik, K. A., & Seol, W. S. (1990). Effect of entrainment on the heat transfer to a heated circular air jet ımpinging on a flat surface. ASME Journal of Heat Transfer, 112(3), 608-611. https://doi.org/10.1115/1.2910430
12. Baughn, J. W., & Shimizu, S. (1989). Heat transfer measurements from a surface with uniform heat flux and an impinging jet. Journal of Heat Transfer, 111(4), 1096-1098. https://doi.org/10.1115/1.3250776
13. Popiel, C. O., & Trass, O. (1991). Visualization of a free and impinging round jet. Experimental Thermal and Fluid Science, 4(3), 253-264. https://doi.org/10.1016/0894-1777(91)90043-Q
14. Mohanty, A. K., & Tawfek, A. A. (1993). Heat transfer due to a round jet impinging normal to a flat surface. International Journal of Heat and Mass Transfer, 36(6), 1639-1647. https://doi.org/10.1016/S0017-9310(05)80073-0
15. Huang, L., & El-Genk, M. S. (1994). Heat transfer of an impinging jet on a flat surface. International Journal of Heat and Mass Transfer, 37(13), 1915-1923. https://doi.org/10.1016/0017-9310(94)90331-X
16. Lytle, D., & Webb, B. W. (1994). Air jet impingement heat transfer at low nozzle-plate spacings. International Journal of Heat and Mass Transfer, 37(12), 1687-1697. https://doi.org/10.1016/0017-9310(94)90059-0
17. Colucci, D. W., & Viskanta, R. (1996). Effect of nozzle geometry on local convective heat transfer to a confined impinging air jet. Experimental Thermal and Fluid Science, 13(1), 71-80. https://doi.org/10.1016/0894-1777(96)00015-5
18. Baydar, E. (1999). Confined impinging air jet at low reynolds numbers. Experimental Thermal and Fluid Science, 19(1), 27-33. https://doi.org/10.1016/S0894-1777(98)10044-4
19. Baydar, E., & Özmen, Y. (2005). An experimental and numerical investigation on a confined impinging air jet at high reynolds numbers. Applied Thermal Engineering, 25(2-3), 409-421. https://doi.org/10.1016/j.applthermaleng.2004.05.016
20. Özmen, Y., & Baydar, E. (2008). Flow structure and heat transfer characteristics of an unconfined impinging air jet at high jet reynolds numbers. Heat and Mass Transfer, 44(11), 2008, 1315-1322. https://doi.org/10.1007/s00231-008-0378-4
21. Miranda, J. M., & Campos, J. B. L. M. (1999). Impinging jets confined by a conical wall: Laminar flow predictions. AIChE Journal, 45, 2273-2285. https://doi.org/10.1002/aic.690451103
22. Behnia, M., Parneix, S., Shabany, Y., & Durbin, P. A. (1999). Numerical study of turbulent heat transfer in confined and unconfined impinging jets. International Journal of Heat Fluid Flow, 20, 1-9. https://doi.org/10.1016/S0142-727X(98)10040-1
23. Herrero, R., & Buchlin, J. M. (2010, Temmuz 24-29). Effect of nozzle shape on local heat transfer distribution in impinging jets. 10th International Conference on Quantitative InfraRed Thermography, Quebec, Kanada. https://doi.org/10.21611/qirt.2010.054
24. Lee, D. H., Bae, J. R., Park, H. J., Lee, J. S. & Ligrani, P. (2011). Confined, milliscale unsteady laminar impinging slot jets and surface nusselts numbers. International Journal of Heat and Mass Transfer, 54:2408–24. https://doi.org/10.1016/j.ijheatmasstransfer.2011.02.021
25. Cavadas, A. S., Pinho, F. T. & Campos, J. B. L. M. (2012). Laminar flow field in a viscous liquid impinging jet confined by inclined plane walls. International Journal of Thermal Sciences, 59, 95-110. https://doi.org/10.1016/j.ijthermalsci.2012.04.004
26. Al Mubarak, A. A., Shaahid, S. M. & Al-Hadhrami, L. M. (2013). Heat transfer in a channel with inclined target surface cooled by single array of centered impinging jets. Thermal Science, 17, 1195-1206. https://doi.org/10.2298/TSCI110630010A
27. Yousefi-Lafouraki, B., Ramiar, A., & Ranjbar, A. A. (2014). Laminar forced convection of a confined slot impinging jet in a converging channel. International Journal of Thermal Sciences, 77, 130-138, 2014. https://doi.org/10.1016/j.ijthermalsci.2013.10.014
28. Bhagwat, A., & Sridharan, A. (2017). Numerical simulation of oblique air jet impingement on a heated flat plate. Journal of Thermal Science and Engineering Application., 1–10. https://doi.org/10.1115/1.4034913
29. Li, Y., Li, B., Qi, F., & Cheung, S. C. P. (2018). Flow and heat transfer of parallel multiple jets obliquely impinging on a flat surface. Applied Thermal Engineering, 10, 2174–2185. https://doi.org/10.1016/j.applthermaleng.2018.01.064
30. Di Venuta, I., Boghi, A., Petracci, I. & Gori, F. (2023). Heat transfer on a flat wall due to a rectangular turbulent jet. International Communications in Heat and Mass Transfer, 144, https://doi.org/10.1016/j.icheatmasstransfer.2023.106769
31. Joshi, J. & Sahu, S. K. (2023). Effect of single and multiple protrusions on thermal performance of slot jet impingement with curved surface. Applied Thermal Engineering, 230. https://doi.org/10.1016/j.applthermaleng.2023.120757
32. Talapati, R. J. & Katti, V. V. (2022). Influence of synthetic air jet temperature on local heat transfer characteristics of synthetic air jet impingement. International Communications in Heat and Mass Transfer, 130, 105796. https://doi.org/10.1016/j.icheatmasstransfer.2021.105796
33. Javidan, M. & Moghadam, A. J. (2022). Effective cooling of a photovoltatic module using jet-impingement array and nanofluid coolant. International Communications in Heat and Mass Transfer, 137. https://doi.org/10.1016/j.icheatmasstransfer.2022.106310
34. Bergman, T. L., Lavine, A. S., Incropera, F. P., & Dewitt, D. P. (2011). Introduction to Heat Transfer. Wiley, Sixth Edition. New Jersey, ABD.
35. Lloyd, J. R., & Moran, W. R. (1974). Natural convection adjacent to horizontal surface of various planforms. Journal of Heat Transfer, 96, 443-447. https://doi.org/10.1115/1.3450224
36. Churchill, S. W., & Chu, H. H. S. (1975). Correlating equations for laminar and turbulent free convection from a vertical plate. International Journal of Heat and Mass Transfer, 18, 1323-1329. https://doi.org/10.1016/0017-9310(75)90243-4
37. Kline, S., & Mcclintock, F. (1953). Describing uncertainties in single-sample experiments. Mechanical Engineering, 75, 3-8.