Bu çalışmada, fotovoltaik panellerin performans parametrelerine (kısa-devre akımı, açık-devre gerilimi ve maksimum çıkış gücü) ait sıcaklık katsayılarını elde etmek için yeni bir yöntem ortaya konmuştur. Eğri uydurma tekniğine dayanan bu yeni yöntem, ölçülen ve hesaplanan performans parametreleri arasındaki en küçük hata değerlerini sağlayan sıcaklık katsayılarını elde etmektedir. Yeni yöntem silikon tabanlı bir fotovoltaik panel için test edilmiştir. Bu panelin; yeni yöntemden elde edilen sıcaklık katsayıları ve kataloğunda sunulan sıcaklık katsayıları dış ölçülen performans parametreleri kullanılarak ortalama karekök hata yaklaşımı ile karşılaştırılmıştır. Sonuç olarak, yeni yöntemden elde edilen sıcaklık katsayılarının, katalog sıcaklık katsayılarından daha iyi bir doğrulukla performans parametrelerinin sıcaklık bağımlılığını ifade ettiği ortaya konmuştur. Mevcut yöntemlerden farklı olarak, yeni yöntem sıcaklık katsayılarını elde etmek için sabit parametrelere, belirli kısıtlamalara veya ilave bir deneysel düzeneğe ihtiyaç duymamaktadır.
Muğla Sıtkı Koçman Üniversitesi Bilimsel Araştırma Projeleri Koordinasyon Birimi
Proje Numarası
08/10 ve 13/181
Kaynakça
1. Dupré, O., 2015. Physics of the thermal behavior of photovoltaic devices To cite this version : HAL Id : tel-01368592 Physics of the thermal behavior of photovoltaic devices.
2. Dupré, O., Vaillon, R., Green, M.A., 2015. Physics of the temperature coefficients of solar cells. Sol. Energy Mater. Sol. Cells 140, 92–100. doi:10.1016/j.solmat.2015.03.025
3. Eke, R., Demircan, H., 2013. Performance analysis of a multi crystalline Si photovoltaic module under Mugla climatic conditions in Turkey. Energy Convers. Manag. 65, 580–586. doi:10.1016/j.enconman.2012.09.007
4. Fanney, A.H., Davis, M.W., Dougherty, B.P., King, D.L., Boyson, W.E., Kratochvil, J. a., 2006. Comparison of Photovoltaic Module Performance Measurements. J. Sol. Energy Eng. 128, 152. doi:10.1115/1.2192559
5. Green, M.A., 2003. General temperature dependence of solar cell performance and implications for device modelling. Prog. Photovoltaics Res. Appl. 11, 333–340. doi:10.1002/pip.496
6. Han, H., Dong, X., Li, B., Yan, H., Verlinden, P.J., Liu, J., Huang, J., Liang, Z., Shen, H., 2018. Degradation analysis of crystalline silicon photovoltaic modules exposed over 30 years in hot-humid climate in China. Sol. Energy 170, 510–519. doi:10.1016/j.solener.2018.05.027
7. Makrides, G., Zinsser, B., Georghiou, G.E., Schubert, M., Werner, J.H., 2009. Temperature behaviour of different photovoltaic systems installed in Cyprus and Germany. Sol. Energy Mater. Sol. Cells 93, 1095–1099. doi:10.1016/j.solmat.2008.12.024
8. Marion, B., Kroposki, B., Emery, K., Cueto, J., Myers, D., Osterwald, C., 1999. Validation of a Photovoltaic Module Energy Ratings Procedure at NREL.
9. Osterwald, C.R., 1986. Translation of device performance measurements to reference conditions. Sol. Cells,18,3-4,Pages 269-279 80401, 269–279.
10. Osterwald, C.R., Glatfelter, T., Burdick, J., 1987. Comparison of the Temperature Coefficients of the Basic I-V parameters for Various Types of Solar Cells. Devices, Energy Convers. 188–193.
11. Paulescu, M., Badescu, V., Dughir, C., 2014. New procedure and field-tests to assess photovoltaic module performance. Energy 70, 49–57. doi:10.1016/j.energy.2014.03.085
12. Perraki, V., 2013. Temperature Dependence on the Photovoltaic Properties of Selected Thin-Film Modules. Int. J. Renew. Sustain. Energy 2, 140. doi:10.11648/j.ijrse.20130204.12
13. Şentürk, A., 2018a. New method for computing single diode model parameters of photovoltaic modules. Renew. Energy 128, 30–36. doi:10.1016/j.renene.2018.05.065
14. Şentürk, A., 2018b. Fotovoltaik modüllerin akım-gerilim eğrilerinin simülasyonunda kullanılacak olan yöntemin seçimi. Balıkesir Üniversitesi Fen Bilim. Enstitüsü Derg. 20, 1–14. doi:10.25092/baunfbed.411779
15. Şentürk, A., 2016. Yeni Bir Yöntem İle Kristal Silisyum Tabanlı Fotovoltaik Modüllerin Elektriksel Performansının Hesaplanması Ve Sıcaklık Katsayılarının (İç Ve Dış) Performansa Olan Etkisinin İncelenmesi. Muğla Sıtkı Kocman University.
16. Senturk, A., Eke, R., 2017. A new method to simulate photovoltaic performance of crystalline silicon photovoltaic modules based on datasheet values. Renew. Energy 103, 58–69. doi:10.1016/j.renene.2016.11.025
17. Şentürk, A., Eke, R., 2018. New method to compare indoor and outdoor temperature coefficients of photovoltaıc modules. Uludağ Univ. J. Fac. Eng. 23, 127–138. doi:10.17482/uumfd.298338
18. Skoplaki, E., Palyvos, J. a., 2009. On the temperature dependence of photovoltaic module electrical performance: A review of efficiency/power correlations. Sol. Energy 83, 614–624. doi:10.1016/j.solener.2008.10.008
19. Tsankov, P., 2015. Study Of The Temperature Coefficients Of Amorphous And Polycrystalline Silicon Photovoltaic Modules Under Real Operating Conditions. Renew. energy sources 2, 123–129. doi:10.7251/COMEN1502123T
20. van Dyk, E.E., Scott, B.J., Meyer, E.L., Leitch, A.W.R., 2000. Temperature Dependence Of Crystallıne Sılıcon Photovoltaıc Module. South African J. Sci. 96, April 2000 96, 198–200.
A NEW METHOD BASED ON CURVE FITTING TECHNIQUE TO ASSESS THE TEMPERATURE COEFFICIENTS OF PHOTOVOLTAIC MODULES
In this study, a new method is introduced to obtain the temperature coefficients of performance
parameters (short-circuit current, open-circuit voltage and the output peak power) of photovoltaic modules.
This new method based on the curve fitting technique obtains the temperature coefficients that guaranty the
smallest error values between measured and calculated performance parameters. The new method has been
tested for a silicon-based photovoltaic module. The temperature coefficients obtained from the new method
and the datasheet-supplied temperature coefficients of this module are compared with each other by using
performance parameters measured in the field through root mean square error tool. As a result, it has been
concluded that temperature coefficients obtained from the proposed new method express the temperature
dependency of the performance parameters more accurately than the data-sheet supplied temperature
coefficients. Unlike existing methods, the new method does not require fixed parameters, specific
constraints, or an additional experimental setup to obtain temperature coefficients.
1. Dupré, O., 2015. Physics of the thermal behavior of photovoltaic devices To cite this version : HAL Id : tel-01368592 Physics of the thermal behavior of photovoltaic devices.
2. Dupré, O., Vaillon, R., Green, M.A., 2015. Physics of the temperature coefficients of solar cells. Sol. Energy Mater. Sol. Cells 140, 92–100. doi:10.1016/j.solmat.2015.03.025
3. Eke, R., Demircan, H., 2013. Performance analysis of a multi crystalline Si photovoltaic module under Mugla climatic conditions in Turkey. Energy Convers. Manag. 65, 580–586. doi:10.1016/j.enconman.2012.09.007
4. Fanney, A.H., Davis, M.W., Dougherty, B.P., King, D.L., Boyson, W.E., Kratochvil, J. a., 2006. Comparison of Photovoltaic Module Performance Measurements. J. Sol. Energy Eng. 128, 152. doi:10.1115/1.2192559
5. Green, M.A., 2003. General temperature dependence of solar cell performance and implications for device modelling. Prog. Photovoltaics Res. Appl. 11, 333–340. doi:10.1002/pip.496
6. Han, H., Dong, X., Li, B., Yan, H., Verlinden, P.J., Liu, J., Huang, J., Liang, Z., Shen, H., 2018. Degradation analysis of crystalline silicon photovoltaic modules exposed over 30 years in hot-humid climate in China. Sol. Energy 170, 510–519. doi:10.1016/j.solener.2018.05.027
7. Makrides, G., Zinsser, B., Georghiou, G.E., Schubert, M., Werner, J.H., 2009. Temperature behaviour of different photovoltaic systems installed in Cyprus and Germany. Sol. Energy Mater. Sol. Cells 93, 1095–1099. doi:10.1016/j.solmat.2008.12.024
8. Marion, B., Kroposki, B., Emery, K., Cueto, J., Myers, D., Osterwald, C., 1999. Validation of a Photovoltaic Module Energy Ratings Procedure at NREL.
9. Osterwald, C.R., 1986. Translation of device performance measurements to reference conditions. Sol. Cells,18,3-4,Pages 269-279 80401, 269–279.
10. Osterwald, C.R., Glatfelter, T., Burdick, J., 1987. Comparison of the Temperature Coefficients of the Basic I-V parameters for Various Types of Solar Cells. Devices, Energy Convers. 188–193.
11. Paulescu, M., Badescu, V., Dughir, C., 2014. New procedure and field-tests to assess photovoltaic module performance. Energy 70, 49–57. doi:10.1016/j.energy.2014.03.085
12. Perraki, V., 2013. Temperature Dependence on the Photovoltaic Properties of Selected Thin-Film Modules. Int. J. Renew. Sustain. Energy 2, 140. doi:10.11648/j.ijrse.20130204.12
13. Şentürk, A., 2018a. New method for computing single diode model parameters of photovoltaic modules. Renew. Energy 128, 30–36. doi:10.1016/j.renene.2018.05.065
14. Şentürk, A., 2018b. Fotovoltaik modüllerin akım-gerilim eğrilerinin simülasyonunda kullanılacak olan yöntemin seçimi. Balıkesir Üniversitesi Fen Bilim. Enstitüsü Derg. 20, 1–14. doi:10.25092/baunfbed.411779
15. Şentürk, A., 2016. Yeni Bir Yöntem İle Kristal Silisyum Tabanlı Fotovoltaik Modüllerin Elektriksel Performansının Hesaplanması Ve Sıcaklık Katsayılarının (İç Ve Dış) Performansa Olan Etkisinin İncelenmesi. Muğla Sıtkı Kocman University.
16. Senturk, A., Eke, R., 2017. A new method to simulate photovoltaic performance of crystalline silicon photovoltaic modules based on datasheet values. Renew. Energy 103, 58–69. doi:10.1016/j.renene.2016.11.025
17. Şentürk, A., Eke, R., 2018. New method to compare indoor and outdoor temperature coefficients of photovoltaıc modules. Uludağ Univ. J. Fac. Eng. 23, 127–138. doi:10.17482/uumfd.298338
18. Skoplaki, E., Palyvos, J. a., 2009. On the temperature dependence of photovoltaic module electrical performance: A review of efficiency/power correlations. Sol. Energy 83, 614–624. doi:10.1016/j.solener.2008.10.008
19. Tsankov, P., 2015. Study Of The Temperature Coefficients Of Amorphous And Polycrystalline Silicon Photovoltaic Modules Under Real Operating Conditions. Renew. energy sources 2, 123–129. doi:10.7251/COMEN1502123T
20. van Dyk, E.E., Scott, B.J., Meyer, E.L., Leitch, A.W.R., 2000. Temperature Dependence Of Crystallıne Sılıcon Photovoltaıc Module. South African J. Sci. 96, April 2000 96, 198–200.
Şentürk, A. (2020). EĞRİ UYDURMA TEKNİĞİNE DAYALI YENİ BİR YÖNTEMLE FOTOVOLTAİK PANELLERİN SICAKLIK KATSAYILARININ ELDE EDİLMESİ. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi, 25(1), 419-434. https://doi.org/10.17482/uumfd.633858
AMA
Şentürk A. EĞRİ UYDURMA TEKNİĞİNE DAYALI YENİ BİR YÖNTEMLE FOTOVOLTAİK PANELLERİN SICAKLIK KATSAYILARININ ELDE EDİLMESİ. UUJFE. Nisan 2020;25(1):419-434. doi:10.17482/uumfd.633858
Chicago
Şentürk, Ali. “EĞRİ UYDURMA TEKNİĞİNE DAYALI YENİ BİR YÖNTEMLE FOTOVOLTAİK PANELLERİN SICAKLIK KATSAYILARININ ELDE EDİLMESİ”. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi 25, sy. 1 (Nisan 2020): 419-34. https://doi.org/10.17482/uumfd.633858.
EndNote
Şentürk A (01 Nisan 2020) EĞRİ UYDURMA TEKNİĞİNE DAYALI YENİ BİR YÖNTEMLE FOTOVOLTAİK PANELLERİN SICAKLIK KATSAYILARININ ELDE EDİLMESİ. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi 25 1 419–434.
IEEE
A. Şentürk, “EĞRİ UYDURMA TEKNİĞİNE DAYALI YENİ BİR YÖNTEMLE FOTOVOLTAİK PANELLERİN SICAKLIK KATSAYILARININ ELDE EDİLMESİ”, UUJFE, c. 25, sy. 1, ss. 419–434, 2020, doi: 10.17482/uumfd.633858.
ISNAD
Şentürk, Ali. “EĞRİ UYDURMA TEKNİĞİNE DAYALI YENİ BİR YÖNTEMLE FOTOVOLTAİK PANELLERİN SICAKLIK KATSAYILARININ ELDE EDİLMESİ”. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi 25/1 (Nisan 2020), 419-434. https://doi.org/10.17482/uumfd.633858.
JAMA
Şentürk A. EĞRİ UYDURMA TEKNİĞİNE DAYALI YENİ BİR YÖNTEMLE FOTOVOLTAİK PANELLERİN SICAKLIK KATSAYILARININ ELDE EDİLMESİ. UUJFE. 2020;25:419–434.
MLA
Şentürk, Ali. “EĞRİ UYDURMA TEKNİĞİNE DAYALI YENİ BİR YÖNTEMLE FOTOVOLTAİK PANELLERİN SICAKLIK KATSAYILARININ ELDE EDİLMESİ”. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi, c. 25, sy. 1, 2020, ss. 419-34, doi:10.17482/uumfd.633858.
Vancouver
Şentürk A. EĞRİ UYDURMA TEKNİĞİNE DAYALI YENİ BİR YÖNTEMLE FOTOVOLTAİK PANELLERİN SICAKLIK KATSAYILARININ ELDE EDİLMESİ. UUJFE. 2020;25(1):419-34.
30.03.2021- Nisan 2021 (26/1) sayımızdan itibaren TR-Dizin yeni kuralları gereği, dergimizde basılacak makalelerde, ilk gönderim aşamasında Telif Hakkı Formu yanısıra, Çıkar Çatışması Bildirim Formu ve Yazar Katkısı Bildirim Formu da tüm yazarlarca imzalanarak gönderilmelidir. Yayınlanacak makalelerde de makale metni içinde "Çıkar Çatışması" ve "Yazar Katkısı" bölümleri yer alacaktır. İlk gönderim aşamasında doldurulması gereken yeni formlara "Yazım Kuralları" ve "Makale Gönderim Süreci" sayfalarımızdan ulaşılabilir. (Değerlendirme süreci bu tarihten önce tamamlanıp basımı bekleyen makalelerin yanısıra değerlendirme süreci devam eden makaleler için, yazarlar tarafından ilgili formlar doldurularak sisteme yüklenmelidir). Makale şablonları da, bu değişiklik doğrultusunda güncellenmiştir. Tüm yazarlarımıza önemle duyurulur.
Bursa Uludağ Üniversitesi, Mühendislik Fakültesi Dekanlığı, Görükle Kampüsü, Nilüfer, 16059 Bursa. Tel: (224) 294 1907, Faks: (224) 294 1903, e-posta: mmfd@uludag.edu.tr