Yüksek Hızlı Oksi- Yakıt Püskürtme Tekniği ile Üretilmiş MCrAlY Esaslı Kaplamaların Sıcak Korozyon Davranışı

Öz

Bu çalışmada küresel grafitli dökme demir (KGDD) altlıklar Yüksek Hızlı Oksi-Yakıt (HVOF) yöntemi ile Ni esaslı AMDRY 9624 ve Ni-Co esaslı AMDRY 9951 olmak üzere iki farklı malzeme ile kaplanmıştır. Kaplamaların mikroyapı ve faz analizleri enerji dağılımlı X-Ray spektrometreli taramalı elektron mikroskobu (SEM-EDX) ve X ışınları difraksiyonu (XRD) yöntemleri kullanılarak yapılmıştır. Bu kaplamaların, %50 V₂O₅ + %50 Na₂SO₄ korozif tuz karışımından oluşan ortamda ve üç farklı sıcaklıkta sıcak korozyon davranışları incelenmiştir. Karakterizasyon çalışmaları neticesinde dökme demir altlıklar üzerinde yaklaşık 80 µm kalınlığında yoğun, porozitesiz bir kaplama tabakası elde edildiği ve kaplama ile altlık malzeme arasında sürekli yapışma sağlandığı görülmüştür. AMDRY 9624 ile kaplanan dökme demirlerin γ ve β intermetalik fazlarını ihtiva ettiği, AMDRY 9951 ticari toz ile üretilen kaplamanın ise sadece γ fazını ihtiva ettiği tespit edilmiştir. Sıcak korozyon testleri sonrasında dökme demir altlığın korozyon tuzlarıyla reaksiyonu sonucu üç sıcaklıkta da FeVO₄ korozyon ürünü oluşmuştur. Kaplama uygulaması sonrası ise 500 ºC de tuzların etkisi ile herhangi bir metal vanadat bileşiği oluşmazken, 600 ve 700 ºC sıcaklıkta çeşitli metal vanadat korozyon ürünlerinin oluşumu belirlenmiştir. 

Anahtar Kelimeler

• Sıcak Korozyon
• HVOF
• Kaplama

Hot Corrosion Behaviour of MCrAlY Based Coatings Fabricated by High Velocity Oxy-Fuel

Öz

In this study, ductile cast irons (DCI) were coated with two different AMDRY 9624 Ni based and AMDRY 9951 Ni-Co based materials by HVOF method. Microstructure and phase analyzes of the coatings were performed to by using Scaning electron microscopy equipped with Energy-dispersive X-ray spectroscopy (SEM-EDX) and X-Ray difraction (XRD) methods. Hot corrosion behavior of DCI are investigated by using %50 V₂O₅ + %50 Na₂SO₄ salts. As a result of the characterization studies it was observed that a dense non-porous coating layer of about 80 μm thickness was obtained on the cast iron samples and continuous adhesion was provided between the coating and the substrate. It has been determined that the cast iron coated with AMDRY 9624 contains γ and β intermetallic phases and the coating produced with AMDRY 9951 commercial powder containsonly γ phase. After the hot corrosion tests, The characterization studies reveal that the reaction of the cast iron substrate with corrosive salts resulted in the formation of FeVO₄ corrosion product at all three temperatures. After coating application, no metal vanadate compound was formed by the reaction of salts with the coatings at 500 ºC. The formation of various metal vanadate corrosion products at 600 and 700 ºC temperature was determined.

Anahtar Kelimeler

• Hot corrosion
• HVOF
• Coating

Kaynakça

1. Cheng, X., Hu, S. B., Song, W. L., & Xiong, X. S. (2013). Improvement in corrosion resistance of a nodular cast iron surface modified by plasma beam treatment. Applied Surface Science, 286, 334-343. doi:10.1016/j.apsusc.2013.09.083
2. Davis, J. R. (2004). Handbook of Thermal Spray Technology. ASM International, 338.
3. Dudziak, T., Du, H. L., Datta, P. K., Wilson, A., Ross, I. M., Moser, M., & Braun, R. (2009). Sulphidation/oxidation behaviour of TiAlCr and Al2Au coated Ti45Al8Nb alloy at 750 degrees C. Corrosion Science, 51(5), 1189-1196. doi:10.1016/j.corsci.2009.02.015
4. El-Kashif, E., El-Banna, E., & Riad, S. (2003). Stepped austempering of GGG 40 ductile cast iron. ISIJ international, 43(7), 1056-1062.
5. Faizul Idham, M. A., Bulan & Syarif, Junaidi & Jaffar, Ahmed & Alias, Siti & Saad, Nor. (2003). Microstructure and XRD of Ductile Iron Using Annealing-Tempering Heat Treatment Process. Applied Mechanics and Materials, 393, 83-87.
6. Fauchais, P., & Vardelle, A. (2012). Thermal sprayed coatings used against corrosion and corrosive wear. In Advanced plasma spray applications: InTech.
7. Fernandes, F., Cavaleiro, A., & Loureiro, A. (2012). Oxidation behavior of Ni-based coatings deposited by PTA on gray cast iron. Surface & Coatings Technology, 207, 196-203. doi:10.1016/j.surfcoat.2012.06.070
8. Grewal, P. S., Chawla, V., & Grewal, J. S. (2011). High Velocity Oxy-fuel Sprayed Coatings- a Review. Journal of the Australian Ceramic Society, 47(2), 30-36.

9. Huang, Z. W., Wang, Z. G., Zhu, S. J., Yuan, F. H., & Wang, F. G. (2008). Effect of HVOF sprayed MCrAIY coating on thermomechanical and isothermal fatigue life of superalloy M963. Surface Engineering (Icse 2007), 373-374, 23-+. doi:DOI 10.4028/www.scientific.net/KEM.373-374.23
10. Itoh, Y., Saitoh, M., & Tamura, M. (2000). Characteristics of MCrAIY coatings sprayed by high velocity oxygen-fuel spraying system. Journal of Engineering for Gas Turbines and Power-Transactions of the Asme, 122(1), 43-49. doi:Doi 10.1115/1.483173
11. Jegadeeswaran, N., Ramesh, M., & Bhat, K. U. (2013). Combating Corrosion Degradation of Turbine Materials Using HVOF Sprayed 25%(Cr 3 C 2-25 (Ni20Cr))+ NiCrAlY Coating. International Journal of Corrosion.
12. Joshi, S. V., & Sivakumar, R. (1991). Particle Behavior during High-Velocity Oxy Fuel Spraying. Surface & Coatings Technology, 50(1), 67-74. doi:Doi 10.1016/0257-8972(91)90195-3
13. Koutsky, J. (2004). High Velocity Oxy-Fuel spraying. Journal of Materials Processing Technology, 157, 557-560. doi:10.1016/j.jmatprotec.2004.07.114
14. Lestan, Z., Milfelner, M., Balic, J., Brezocnik, M., & Karabegovic, I. (2013). Laser deposition of Metco 15E, Colmony 88 and VIM CRU 20 powders on cast iron and low carbon steel. International Journal of Advanced Manufacturing Technology, 66(9-12), 2023-2028. doi:10.1007/s00170-012-4478-4
15. Liu, J. L., Shi, G. Q., Ding, P. D., Ye, H., & Ou, Z. X. (1997). Features of laser alloying of grey cast iron. Lasers in Engineering, 6(2), 81-101.
16. Maco, A. L., & Belzunce, F. J. (1998). Laser surface hardening of gray cast irons. Revista De Metalurgia, 34(2), 126-130. doi:DOI 10.3989/revmetalm.1998.v34.i2.674
17. Montero, X., & Galetz, M. C. (2018). Sulfate–Vanadate-Induced Corrosion of Different Alloys. Oxidation of Metals, 89(3), 499-516. doi:10.1007/s11085-017-9831-4
18. O'Rourke, R. (2001). Cast iron: The engineered metal. Advanced Materials & Processes, 159(1), 65-68.
19. Ocelik, V., de Oliveira, U., de Boer, M., & de Hosson, J. T. M. (2007). Thick Co-based coating on cast iron by side laser cladding: Analysis of processing conditions and coating properties. Surface & Coatings Technology, 201(12), 5875-5883. doi:10.1016/j.surfcoat.2006.10.044
20. Saeidi, S., Voisey, K. T., & McCartney, D. G. (2009). The Effect of Heat Treatment on the Oxidation Behavior of HVOF and VPS CoNiCrAlY Coatings. Journal of Thermal Spray Technology, 18(2), 209-216.
21. Saeidi, S., Voisey, K. T., & McCartney, D. G. (2011). Mechanical Properties and Microstructure of VPS and HVOF CoNiCrAlY Coatings. Journal of Thermal Spray Technology, 20(6), 1231-1243.
22. Seiersten, M., & Kofstad, P. (1987). Sodium Vanadate-Induced Corrosion of Nickel and Mcraiy Coatings on Inconel-600. Materials Science and Technology, 3(7), 576-583. doi:Doi 10.1080/02670836.1987.11782270
23. Seo, D., & Ogawa, K. (2012). Isothermal Oxidation Behavior of Plasma Sprayed MCrAlY Coatings. In Advanced Plasma Spray Applications: InTech.
24. Shibata, M., Kuroda, S., Watanabe, M., & Sakamoto, Y. (2006). Oxidation property of CoNiCrAlY coatings prepared by various thermal spraying techniques. High-Temperature Oxidation and Corrosion 2005, 522-523, 339-344. doi:DOI 10.4028/www.scientific.net/MSF.522-523.339
25. Singh, R. (2009). Cast Iron Metallurgy. Materials Performance, 48(9), 58-61.
26. Taheri, M., Valefi, Z., & Zangeneh-Madar, K. (2012). Influence of HVOF process parameters on microstructure and bond strength of NiCrAlY coatings. Surface Engineering, 28(4), 266-272. doi:10.1179/1743294411Y.0000000024
27. Vetter, J., Barbezat, G., Crummenauer, J., & Avissar, J. (2005). Surface treatment selections for automotive applications. Surface & Coatings Technology, 200(5-6), 1962-1968. doi:DOI 10.1016/j.surfcoat.2005.08.011
28. Wright, I. G., & Pint, B. A. (2005). Bond coating issues in thermal barrier coatings for industrial gas turbines. Proceedings of the Institution of Mechanical Engineers Part a-Journal of Power and Energy, 219(A2), 101-107. doi:10.1243/095765005x6836
29. Yoganandh, J., Natarajan, S., & Babu, S. P. K. (2013). Erosion Behaviour of WC-Co-Cr Thermal Spray Coated Grey Cast Iron under Mining Environment. Transactions of the Indian Institute of Metals, 66(4), 437-443. doi:10.1007/s12666-013-0262-x