Araştırma Makalesi
BibTex RIS Kaynak Göster

TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING

Yıl 2021, Cilt: 5 Sayı: 2, 281 - 292, 31.08.2021
https://doi.org/10.46519/ij3dptdi.955405

Öz

The importance of 3D printing as a builder of the digital future is growing all the time. When it comes to the digital future, one clear goal is that, for example, spare parts are no longer necessarily shipped from factories around the world, but are 3D printed using a digital model of the spare part purchased from the manufacturer. Using 3D printers for replacement printing or home use is relatively simple. However, with 3D printers, you come across a wide variety of situations that require fault detection, troubleshooting, and general adjustment.

This article highlights the most common problems with 3D printers. The technologies chosen for this study are Vat Photopolymerization and FDM (Fused Deposition Modeling) printing technologies because they are very common techniques for spare parts printing and home use. This study was conducted in concrete way, experimenting and producing problems intentionally, then solving them with solutions and techniques, which are common and gained through experience.

As a result, this article is written as a guide to the most common problems with these chosen technologies. Solutions to the problems are showcased in simple and effective steps. After all, this study showed well the diversity of problem situations in 3D printing as well as the need for concrete expertise in troubleshooting solutions. The problems faced and tackled in this study were the most common ones but there can exist other problems too.

Destekleyen Kurum

Erasmus+

Teşekkür

Thank you EU Erasmus+ for the funding for the 3DPRINT-DnB project. Thank you also to the coordinators from the University of Wolverhampton and all the project partners for the good collaboration!

Kaynakça

  • Lukka, K., “Konstruktiivinen tutkimusote”, [Constructive research approach] [article in Finnish], https://metodix.fi/2014/05/19/lukka-konstruktiivinen-tutkimusote/, April 1, 2021.
  • Lehtiranta, L., Junnonen, J.-M., Kärnä, S., Pekuri L., “The Constructive Research Approach: Problem Solving for Complex Projects”, In Pasian B. editor, Designs, Methods and Practices for Research of Project Management, Pages 95-106, Gower Publishing Limited, Aldershot, 2015.
  • Olkkonen, T., “Johdatus teollisuustalouden tutkimustyöhön”, Report, [Introduction to industrial economics research] [report in Finnish], Helsinki University of Technology, Helsinki, 1993.
  • Aaltio-Marjosola, I., “Casetutkimus metodisena lähestymistapana”, [Case study as a methodological approach] [article in Finnish], https://metodix.fi/2014/05/19/aaltio-marjosola-casetutkimus/, April 2, 2021.
  • Yin, R., “Case Study Research: Design and Methods”, 3rd ed., Sage Publications, London, 2003.
  • Bell, C., “Maintaining and Troubleshooting Your 3D Printer”, 1st ed., Pages 3-6, Apress L. P., New York, 2014.
  • Horvath, J., Cameron, R., “A Guide to Modeling, Printing, and Prototyping”, 2nd ed., Pages 3-18, Apress L. P., New York, 2020.
  • Griffey, J., “The Types of 3-D Printing”, Library Technology Reports, Vol. 50, Issue 1, Pages 8-12, 2014.
Yıl 2021, Cilt: 5 Sayı: 2, 281 - 292, 31.08.2021
https://doi.org/10.46519/ij3dptdi.955405

Öz

Kaynakça

  • Lukka, K., “Konstruktiivinen tutkimusote”, [Constructive research approach] [article in Finnish], https://metodix.fi/2014/05/19/lukka-konstruktiivinen-tutkimusote/, April 1, 2021.
  • Lehtiranta, L., Junnonen, J.-M., Kärnä, S., Pekuri L., “The Constructive Research Approach: Problem Solving for Complex Projects”, In Pasian B. editor, Designs, Methods and Practices for Research of Project Management, Pages 95-106, Gower Publishing Limited, Aldershot, 2015.
  • Olkkonen, T., “Johdatus teollisuustalouden tutkimustyöhön”, Report, [Introduction to industrial economics research] [report in Finnish], Helsinki University of Technology, Helsinki, 1993.
  • Aaltio-Marjosola, I., “Casetutkimus metodisena lähestymistapana”, [Case study as a methodological approach] [article in Finnish], https://metodix.fi/2014/05/19/aaltio-marjosola-casetutkimus/, April 2, 2021.
  • Yin, R., “Case Study Research: Design and Methods”, 3rd ed., Sage Publications, London, 2003.
  • Bell, C., “Maintaining and Troubleshooting Your 3D Printer”, 1st ed., Pages 3-6, Apress L. P., New York, 2014.
  • Horvath, J., Cameron, R., “A Guide to Modeling, Printing, and Prototyping”, 2nd ed., Pages 3-18, Apress L. P., New York, 2020.
  • Griffey, J., “The Types of 3-D Printing”, Library Technology Reports, Vol. 50, Issue 1, Pages 8-12, 2014.
Toplam 8 adet kaynakça vardır.

Ayrıntılar

Birincil Dil İngilizce
Konular Mühendislik
Bölüm Araştırma Makalesi
Yazarlar

Joonas Kortelainen Bu kişi benim 0000-0001-5393-2627

Mirka Leino 0000-0002-0465-4197

Tommi Lehtinen Bu kişi benim 0000-0002-1011-6563

Yayımlanma Tarihi 31 Ağustos 2021
Gönderilme Tarihi 21 Haziran 2021
Yayımlandığı Sayı Yıl 2021 Cilt: 5 Sayı: 2

Kaynak Göster

APA Kortelainen, J., Leino, M., & Lehtinen, T. (2021). TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING. International Journal of 3D Printing Technologies and Digital Industry, 5(2), 281-292. https://doi.org/10.46519/ij3dptdi.955405
AMA Kortelainen J, Leino M, Lehtinen T. TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING. IJ3DPTDI. Ağustos 2021;5(2):281-292. doi:10.46519/ij3dptdi.955405
Chicago Kortelainen, Joonas, Mirka Leino, ve Tommi Lehtinen. “TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING”. International Journal of 3D Printing Technologies and Digital Industry 5, sy. 2 (Ağustos 2021): 281-92. https://doi.org/10.46519/ij3dptdi.955405.
EndNote Kortelainen J, Leino M, Lehtinen T (01 Ağustos 2021) TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING. International Journal of 3D Printing Technologies and Digital Industry 5 2 281–292.
IEEE J. Kortelainen, M. Leino, ve T. Lehtinen, “TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING”, IJ3DPTDI, c. 5, sy. 2, ss. 281–292, 2021, doi: 10.46519/ij3dptdi.955405.
ISNAD Kortelainen, Joonas vd. “TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING”. International Journal of 3D Printing Technologies and Digital Industry 5/2 (Ağustos 2021), 281-292. https://doi.org/10.46519/ij3dptdi.955405.
JAMA Kortelainen J, Leino M, Lehtinen T. TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING. IJ3DPTDI. 2021;5:281–292.
MLA Kortelainen, Joonas vd. “TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING”. International Journal of 3D Printing Technologies and Digital Industry, c. 5, sy. 2, 2021, ss. 281-92, doi:10.46519/ij3dptdi.955405.
Vancouver Kortelainen J, Leino M, Lehtinen T. TROUBLESHOOTING AND TACKLING THE COMMON PROBLEMS IN VAT PHOTOPOLYMERIZATION AND FDM 3D PRINTING. IJ3DPTDI. 2021;5(2):281-92.

 download

Uluslararası 3B Yazıcı Teknolojileri ve Dijital Endüstri Dergisi Creative Commons Atıf-GayriTicari 4.0 Uluslararası Lisansı ile lisanslanmıştır.