Plazma Püskürtme İşlemi ile Cr3C2 Kaplamanın Dizel Motorun Egzoz Borusu Üzerine Etkilerinin Araştırılması

Öz

Egzoz sisteminin ömrü, yüksek egzoz gazı sıcaklığı, egzoz gazındaki kimyasal çözücüler, su buharı, yağışlı havalarda su, çamur, yollarda dökülen tuz, kış aylarında donmayı önlemek için vb. Olumsuz faktörler altında hızla azalır. İçten Yanmalı motorların, kullanıldığı bölgelere ve koşullara bağlı olarak bir süre sonra değiştirilmeleri gerekir. Bu çalışmada, bir dizel motorun egzoz borusunun dış parçaları, plazma sprey yöntemi kullanılarak 100 mikron kalınlığında krom karbür (Cr3C2) malzemesi ile kaplandı. Dışarıdan etkileyen kimyasal ve fiziksel çözücünün ve deforme edici faktörlerin etkisi, egzoz borusunun krom karbür (Cr3C2) malzemesi ile kaplanmasıyla incelenmiştir. Deneyler sonucunda korozyon direncinin% 85 oranında arttığı belirlenmiştir. Taramalı elektron mikroskobu (SEM), mikro sertlik, EDAX ve X-RD analizlerine göre, kaplamanın ana materyali üzerinde düzgün bir yapı oluşturduğu gözlendi. Böylece, egzoz sisteminin ömrünü azaltan faktörlerin kaplama malzemesi ile karşılandığı, yüzey yapısının gelişmiş ve malzeme ömrünün standart egzoz borusuna kıyasla arttığı sonucuna varılabilir.

Anahtar Kelimeler

• Plazma Sprey Kaplama,Krom Karbür,Dizel Motorlar

Investigation of the Effect of Cr3C2 Coating by Plasma Spray Process on Exhaust Pipe of a Diesel Engine

Öz

Lifetime of exhaust system decreases rapidly under negative factors such as high exhaust gas temperature, chemical solvents in exhaust gas, water vapor, water in rainy weather, mud, salt poured on the roads to prevent frosting in winter months, etc. Exhaust system of internal combustion engines need to be replaced after a while based on regions and conditions in which they are used. In this study, outer parts of exhaust pipe of a diesel engine were coated with 100-micron-thick chromium carbide (Cr3C2) material by using plasma spray method. The effect of chemical and physical solvent and deforming factors that affect externally was examined by coating exhaust pipe with chromium carbide (Cr3C2) material. As a result of experiments, it was determined that corrosion resistance increased by 85%. According to scanning electron microscope (SEM), micro hardness, EDAX, and X-RD analyses, the coating was observed to generate a uniform structure on substrate material. Thus, it could be concluded that factors decreasing the lifetime of exhaust system were met by coating material, the surface structure enhanced, and material lifetime increased compared to standard exhaust pipe.

Anahtar Kelimeler

• Plasma Spray Coating,Chromium Carbide,diesel engines

Kaynakça

1. Aw PK, Tan ALK, Tan TP, Qiu J, 2008, Corrosion resistance of tungsten carbide based cermet coatings deposited by High Velocity Oxy-Fuel spray process, Thin Solid Films, 516, 5710–5715.
2. Hong S, Wu Y, Wang Q, Ying G, Li G, Gao W, Wang B, Guo W, 2013, Microstructure and cavitation–silt erosion behavior of high-velocity oxygen–fuel (HVOF) sprayed Cr3C2–NiCr coating, Surface and Coatings Technology, 225, 85–91.
3. Janka L, Norpoth J, Eicher S, Ripoll MR, Vuoristo P, 2016, Improving the toughness of thermally sprayed Cr3C2-NiCr hardmetal coatings by laser post-treatment, Materials & Design, 98, 135–142.
4. Kamal S, Jayaganthan R, Prakash S, 2009, High temperature oxidation studies of detonation-gun-sprayed Cr3C2–NiCr coating on Fe- and Ni-based superalloys in air under cyclic condition at 900 °C, Journal of Alloys and Compounds, 472, 378–389.
5. Matthews S, James B, Hyland M, 2013, High temperature erosion–oxidation of Cr3C2–NiCr thermal spray coatings under simulated turbine conditions, Corrosion Science, 70, 203–211.
6. Mudgal D, Singh S, Prakash S, J, 2015, Hot Corrosion Behavior of Bare, Cr3C2-(NiCr) and Cr3C2-(NiCr) + 0.2wt.%Zr Coated SuperNi 718 at 900 °C, Journal of Materials Engineering and Performance, 24, 1–15.
7. Murthy JKN, Prasad KS, Gopinath K, Venkataraman B, 2010, Characterisation of HVOF sprayed Cr3C2-50(Ni20Cr) coating and the influence of binder properties on solid particle erosion behavior, Surface and Coatings Technology, 204, 3975–3985.
8. Nicolaus M, Möhwald K, Maier HJ, 2017, A Combined Brazing and Aluminizing Process for Repairing Turbine Blades by Thermal Spraying Using the Coating System NiCrSi/NiCoCrAlY/Al, Journal of Thermal Spray Technology, 26, 1659–1668.

9. Sharafat S, Kobayashi A, Chan Y, Ghoniem NM, 2002, Plasma spraying of micro-composite thermal barrier coatings, Vacuum 65, 415-425.
10. Singh B, Singh G, Sidhu BS, 2018, Analysis of Corrosion Behavior and Surface Properties of Plasma-Sprayed HA/Ta Coating on CoCr Alloy, Journal of Thermal Spray Technology, 27, 1428–1435.
11. Suarez M, Bellayer S, Traisnel M, Gonzalez W, Chicot D, Lesage J, Puchi-Cabrera ES, Staia MH, 2008, Corrosion behavior of Cr3C2–NiCr vacuum plasma sprayed coatings, Surface and Coatings Technology, 202, 4566–4571.
12. Zhou W, Zhou K, Deng C, Zeng K, Li Y, 2017, Hot corrosion behaviour of HVOF-sprayed Cr3C2-NiCrMoNbAl coating, Surface and Coatings Technology, 309, 849–859.