Araştırma Makalesi

The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates

Cilt: 3 Sayı: 2 21 Aralık 2022
Abdullah Şişman *
PDF İndir
Journal of Science, Technology and Engineering Research Kapak Journal of Science, Technology and Engineering Research
TR EN

The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates

Abstract

In this study, in the repair of angled channel aluminum plates; The effects of channel angle and patch sizes on tensile stress behavior were investigated experimentally. For this purpose, aluminum 2024 T3 sheets with angled channels with varying channel angles were prepared. These plates were subjected to tensile loads and their failure loads were investigated experimentally. Then, using DP460 adhesive material, angled channel aluminum 2024 T3 sheets were repaired using double-sided lap joints with aluminum 2024 T3 patches of varying sizes, and the repaired samples were subjected to tensile load, the effect of channel angle and patch size change on failure loads and stress behaviors in repair was also experimentally examined and the success of the repair was evaluated.

Keywords

Alumınum Plates , Stress Distributions , Failure Loads , Adhesive Joints , Double-Sided Lap Joints.

Kaynakça

  1. Ayaz Y., Temiz Ş., "Analysis of Embedded Adhesive Joints with Double Reinforced Patches", Erzincan University Journal of Science and Technology , vol.5, pp.165-172, 2012.
  2. Ergün, Raşit Koray, “Experimental and Numerical Investigation of the Effect of Repairing Elliptical Perforated Aluminum Sheets with Composite Patch on Tensile Behavior”, Kahramanmaraş Sütçü İmam University Institute of Science and Technology, Unpublished Master Thesis, Kahramanmaraş 2014.
  3. Li HCH ., Wangb J., Baker A., “Rapid composite bonded Repair for helicopter Tail Drive Shafts ”, Composites : Part B , 43 : (2012), pp. 1579-1585.
  4. Rachid M. , Serier B., Bachir BB, Belhouari M., “ Numerical Analysis of the patch shape Effects on the Performances of Bonded composite Repair in Aircraft Structures ”, Composites : Part B , 43: (2012), pp . 391-397.
  5. Ramji M. , Srilakshmi R., Bhanu PM, “ Towards Optimization of Patch shape on the Performance of Bonded composite Repair Using FEM”, Composites : Part B, 45: (2013), pp. 710-720.
  6. Soy, Ugur, Adhesive Repair of Al 2024-T3 Alloy Plate with Composite Patch with the Help of Computer Aided Modeling , (Sakarya University Institute of Science and Technology, Published Master's Thesis), Sakarya 2005.
  7. Single, Gökhan, “Single and Double-Action Adhesive Connections”, Gazi University Institute of Science, Published Master Thesis, Ankara 2011 .

Ayrıntılar

Birincil Dil

İngilizce

Konular

Makine Mühendisliği

Bölüm

Araştırma Makalesi

Yazarlar

Yayımlanma Tarihi

21 Aralık 2022

Gönderilme Tarihi

6 Kasım 2022

Kabul Tarihi

14 Kasım 2022

Yayımlandığı Sayı

Yıl 2022 Cilt: 3 Sayı: 2

DOI

https://doi.org/10.53525/jster.1200039

IZ

https://izlik.org/JA87FR42KE

Kaynak Göster

RIS / Bibtex
APA
Şişman, A. (2022). The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates. Journal of Science, Technology and Engineering Research, 3(2), 60-67. https://doi.org/10.53525/jster.1200039
AMA
1.Şişman A. The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates. Journal of Science, Technology and Engineering Research. 2022;3(2):60-67. doi:10.53525/jster.1200039
Chicago
Şişman, Abdullah. 2022. “The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates”. Journal of Science, Technology and Engineering Research 3 (2): 60-67. https://doi.org/10.53525/jster.1200039.
EndNote
Şişman A (01 Aralık 2022) The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates. Journal of Science, Technology and Engineering Research 3 2 60–67.
IEEE
[1]A. Şişman, “The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates”, Journal of Science, Technology and Engineering Research, c. 3, sy 2, ss. 60–67, Ara. 2022, doi: 10.53525/jster.1200039.
ISNAD
Şişman, Abdullah. “The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates”. Journal of Science, Technology and Engineering Research 3/2 (01 Aralık 2022): 60-67. https://doi.org/10.53525/jster.1200039.
JAMA
1.Şişman A. The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates. Journal of Science, Technology and Engineering Research. 2022;3:60–67.
MLA
Şişman, Abdullah. “The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates”. Journal of Science, Technology and Engineering Research, c. 3, sy 2, Aralık 2022, ss. 60-67, doi:10.53525/jster.1200039.
Vancouver
1.Abdullah Şişman. The Effect of Damage Line and Patch Dimensions on Tensile Stress Behavior in Repair of Aluminum Plates. Journal of Science, Technology and Engineering Research. 01 Aralık 2022;3(2):60-7. doi:10.53525/jster.1200039
Dergide yayınlanan çalışmalar
Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 (CC BY-NC-ND 4.0) Uluslararası Lisansı ile lisanslanmıştır.
by-nc-nd.png

Free counters!